# Nuclear fuel

﻿
Nuclear fuel
Nuclear Fuel Process
A graph comparing nucleon number against binding energy
Close-up of a replica of the core of the research reactor at the Institut Laue-Langevin

Nuclear fuel is a material that can be 'consumed' by fission or fusion to derive nuclear energy. Nuclear fuels are the most dense sources of energy available. Nuclear fuel in a nuclear fuel cycle can refer to the fuel itself, or to physical objects (for example bundles composed of fuel rods) composed of the fuel material, mixed with structural, neutron moderating, or neutron reflecting materials.

Most nuclear fuels contain heavy metal fissile elements that can be made to undergo a nuclear fission chain reaction in a nuclear reactor. The most common fissile nuclear fuels are Uranium 235 (235U) and Plutonium 239 (239Pu). The actions of mining, refining, purifying, using, and ultimately disposing of these elements together make up the nuclear fuel cycle.

Not all nuclear fuels are used in fission reactors. Plutonium-238 and some other elements are used to produce small amounts of nuclear power by radioactive decay in radioisotope thermoelectric generators and other atomic batteries. Light nuclides such as 3H (tritium) are used as fuel for nuclear fusion.

## Oxide fuel

For fission reactors, the fuel (typically based on Uranium) is usually based on the metal oxide; the oxides are used rather than the metals themselves because the oxide melting point is much higher than that of the metal and because it cannot burn, being already in the oxidized state. The thermal conductivity of uranium dioxide is low; it is affected by porosity and burn-up. The burn-up results in fission products being dissolved in the lattice (such as lanthanides), the precipitation of fission products such as palladium, the formation of fission gas bubbles due to fission products such as xenon and krypton and radiation damage of the lattice. The low thermal conductivity can lead to overheating of the center part of the pellets during use. The porosity results in a decrease in both the thermal conductivity of the fuel and the swelling which occurs during use.

According to the International Nuclear Safety Center [1] the thermal conductivity of uranium dioxide can be predicted under different conditions by a series of equations.

The bulk density of the fuel can be related to the thermal conductivity

Where ρ is the bulk density of the fuel and ρtd is the theoretical density of the uranium dioxide.

Then the thermal conductivity of the porous phase (Kf) is related to the conductivity of the perfect phase (Ko, no porosity) by the following equation. Note that s is a term for the shape factor of the holes.

Kf = Ko(1 − p/1 + (s − 1)p)

Rather than measuring the thermal conductivity using the traditional methods in physics such as Lees' disk, the Forbes' method or Searle's bar it is common to use a laser flash method where a small disc of fuel is placed in a furnace. After being heated to the required temperature one side of the disc is illuminated with a laser pulse, the time required for the heat wave to flow through the disc, the density of the disc, and the thickness of the disk can then be used to calculated to give the thermal conductivity.

λ = ρCpα

If t1/2 is defined as the time required for the non illuminated surface to experience half its final temperature rise then.

α = 0.1388 L2/t1/2
• L is the thickness of the disc

For details see [2]

### UOX

The thermal conductivity of zirconium metal and uranium dioxide as a function of temperature

Uranium dioxide is a black semiconductor solid. It can be made by reacting uranyl nitrate with a base (ammonia) to form a solid (ammonium uranate). It is heated (calcined) to form U3O8 that can then be converted by heating in an argon / hydrogen mixture (700 °C) to form UO2. The UO2 is then mixed with an organic binder and pressed into pellets, these pellets are then fired at a much higher temperature (in H2/Ar) to sinter the solid. The aim is to form a dense solid which has few pores.

The thermal conductivity of uranium dioxide is very low compared with that of zirconium metal, and it goes down as the temperature goes up.

It is important to note that the corrosion of uranium dioxide in an aqueous environment is controlled by similar electrochemical processes to the galvanic corrosion of a metal surface.

### MOX

Mixed oxide, or MOX fuel, is a blend of plutonium and natural or depleted uranium which behaves similarly (though not identically) to the enriched uranium feed for which most nuclear reactors were designed. MOX fuel is an alternative to low enriched uranium (LEU) fuel used in the light water reactors which predominate nuclear power generation.

Some concern has been expressed that used MOX cores will introduce new disposal challenges, though MOX is itself a means to dispose of surplus plutonium by transmutation.

Currently (March, 2005) reprocessing of commercial nuclear fuel to make MOX is done in England and France, and to a lesser extent in Russia, India and Japan. China plans to develop fast breeder reactors and reprocessing.

The Global Nuclear Energy Partnership, is a U.S. plan to form an international partnership to see spent nuclear fuel reprocessed in a way that renders the plutonium in it usable for nuclear fuel but not for nuclear weapons. Reprocessing of spent commercial-reactor nuclear fuel has not been permitted in the United States due to nonproliferation considerations. All of the other reprocessing nations have long had nuclear weapons from military-focused "research"-reactor fuels except for Japan.

## Metal fuel

Metal fuels have the advantage of a much higher heat conductivity than oxide fuels but cannot survive equally high temperatures. Metal fuels have a long history of use, stretching from the Clementine reactor in 1946 to many test and research reactors. Metal fuels have the potential for the highest fissile atom density. Metal fuels are normally alloyed, but some metal fuels have been made with pure uranium metal. Uranium alloys that have been used include uranium aluminum, uranium zirconium, uranium silicon, uranium molybdenum, and uranium zirconium hydride. Any of the aforementioned fuels can be made with plutonium and other actinides as part of a closed nuclear fuel cycle. Metal fuels have been used in water reactors and liquid metal fast breeder reactors, such as EBR-II.

### TRIGA fuel

TRIGA fuel is used in TRIGA (Training, Research, Isotopes, General Atomics) reactors. The TRIGA reactor uses uranium-zirconium-hydride (UZrH) fuel, which has a prompt negative temperature coefficient, meaning that as the temperature of the core increases, the reactivity decreases—so it is highly unlikely for a meltdown to occur. Most cores that use this fuel are "high leakage" cores where the excess leaked neutrons can be utilized for research. TRIGA fuel was originally designed to use highly enriched uranium, however in 1978 the U.S. Department of Energy launched its Reduced Enrichment for Research Test Reactors program, which promoted reactor conversion to low-enriched uranium fuel. A total of 35 TRIGA reactors have been installed at locations across the USA. A further 35 reactors have been installed in other countries.

### Actinide fuel

In a fast neutron reactor, the minor actinides produced by neutron capture of uranium and plutonium can be used as fuel. Metal actinide fuel is typically an alloy of zirconium, uranium, plutonium and the minor actinides. It can be made inherently safe as thermal expansion of the metal alloy will increase neutron leakage.

## Ceramic fuels

Ceramic fuels other than oxides have the advantage of high heat conductivities and melting points, but they are more prone to swelling than oxide fuels and are much less well understood.

### Uranium nitride

This is often the fuel of choice for reactor designs that NASA produces, one advantage is that UN has a better thermal conductivity than UO2. Uranium nitride has a very high melting point. This fuel has the disadvantage that unless 15N was used (in place of the more common 14N) that a large amount of 14C would be generated from the nitrogen by the (n,p) reaction. As the nitrogen required for such a fuel would be so expensive it is likely that the fuel would have to be reprocessed by a pyro method to enable to the 15N to be recovered. It is likely that if the fuel was processed and dissolved in nitric acid that the nitrogen enriched with 15N would be diluted with the common 14N.

### Uranium carbide

Much of what is known about uranium carbide is in the form of pin-type fuel elements for liquid metal fast breeder reactors during their intense study during the '60s and '70s. However, recently there has been a revived interest in uranium carbide in the form of plate fuel and most notably, micro fuel particles (such as TRISO particles).

The high thermal conductivity and high melting point make uranium carbide an attractive fuel. In addition, because of the absence of oxygen in this fuel (during the course of irradiation, excess gas pressure can build from the formation of O2 or other gases) as well as the ability to complement a ceramic coating (a ceramic-ceramic interface has structural and chemical advantages), uranium carbide could be the ideal fuel candidate for certain Generation IV reactors such as the gas-cooled fast reactor.

## Liquid fuels

### Molten salts

These include fuels where the fuel is dissolved in the coolant. They were used in the Molten Salt Reactor Experiment and numerous other liquid core reactor experiments, such as the liquid fluoride thorium reactor. The liquid fuel for the molten salt reactor was a mixture of lithium, beryllium, thorium and uranium fluorides: LiF-BeF2-ThF4-UF4 (72-16-12-0.4 mol%). It had a peak operating temperature of 705 °C in the experiment, but could have operated at much higher temperatures, since the boiling point of the molten salt was in excess of 1400 °C.

### Aqueous solutions of uranyl salts

The aqueous homogeneous reactors use a solution of uranyl sulfate or other uranium salt in water. This homogenous reactor type has not been used for any large power reactors. One of its disadvantages is that the fuel is in a form which is easy to disperse in the event of an accident.

## Common physical forms of nuclear fuel

Uranium dioxide (UO2) powder is compacted to cylindrical pellets and sintered at high temperatures to produce ceramic nuclear fuel pellets with a high density and well defined physical properties and chemical composition. A grinding process is used to achieve a uniform cylindrical geometry with narrow tolerances. Such fuel pellets are then stacked and filled into the metallic tubes. The metal used for the tubes depends on the design of the reactor. Stainless steel was used in the past, but most reactors now use a zirconium alloy which, in addition to being highly corrosion-resistant, has low neutron absorption. The tubes containing the fuel pellets are sealed: these tubes are called fuel rods. The finished fuel rods are grouped into fuel assemblies that are used to build up the core of a power reactor.

Cladding is the outer layer of the fuel rods, standing between the coolant and the nuclear fuel. It is made of a corrosion-resistant material with low absorption cross section for thermal neutrons, usually Zircaloy or steel in modern constructions, or magnesium with small amount of aluminium and other metals for the now-obsolete Magnox reactors. Cladding prevents radioactive fission fragments from escaping the fuel into the coolant and contaminating it.

### PWR fuel

PWR fuel assembly (also known as a fuel bundle) This fuel assembly is from a pressurized water reactor of the nuclear-powered passenger and cargo ship NS Savannah. Designed and built by the Babcock and Wilcox Company.

Pressurized water reactor (PWR) fuel consists of cylindrical rods put into bundles. A uranium oxide ceramic is formed into pellets and inserted into Zircaloy tubes that are bundled together. The Zircaloy tubes are about 1 cm in diameter, and the fuel cladding gap is filled with helium gas to improve the conduction of heat from the fuel to the cladding. There are about 179-264 fuel rods per fuel bundle and about 121 to 193 fuel bundles are loaded into a reactor core. Generally, the fuel bundles consist of fuel rods bundled 14x14 to 17x17. PWR fuel bundles are about 4 meters in length. In PWR fuel bundles, control rods are inserted through the top directly into the fuel bundle. The fuel bundles usually are enriched several percent in 235U. The uranium oxide is dried before inserting into the tubes to try to eliminate moisture in the ceramic fuel that can lead to corrosion and hydrogen embrittlement. The Zircaloy tubes are pressurized with helium to try to minimize pellet-cladding interaction which can lead to fuel rod failure over long periods.

### BWR fuel

In boiling water reactors (BWR), the fuel is similar to PWR fuel except that the bundles are "canned"; that is, there is a thin tube surrounding each bundle. This is primarily done to prevent local density variations from affecting neutronics and thermal hydraulics of the reactor core. In modern BWR fuel bundles, there are either 91, 92, or 96 fuel rods per assembly depending on the manufacturer. A range between 368 assemblies for the smallest and 800 assemblies for the largest U.S. BWR forms the reactor core. Each BWR fuel rod is back filled with helium to a pressure of about three atmospheres (300 kPa).

### CANDU fuel

CANDU fuel bundles Two CANDU ("CANada Deuterium Uranium") fuel bundles, each about 50 cm in length, 10 cm in diameter. Photo courtesy of Atomic Energy of Canada Ltd.

CANDU fuel bundles are about a half meter in length and 10 cm in diameter. They consist of sintered (UO2) pellets in zirconium alloy tubes, welded to zirconium alloy end plates. Each bundle is roughly 20 kg, and a typical core loading is on the order of 4500-6500 bundles, depending on the design. Modern types typically have 37 identical fuel pins radially arranged about the long axis of the bundle, but in the past several different configurations and numbers of pins have been used. The CANFLEX bundle has 43 fuel elements, with two element sizes. It is also about 10 cm (4 inches) in diameter, 0.5 m (20 in) long and weighs about 20 kg (44 lb) and replaces the 37-pin standard bundle. It has been designed specifically to increase fuel performance by utilizing two different pin diameters. Current CANDU designs do not need enriched uranium to achieve criticality (due to their more efficient heavy water moderator), however, some newer concepts call for low enrichment to help reduce the size of the reactors.

## Less common fuel forms

Various other nuclear fuel forms find use in specific applications, but lack the widespread use of those found in BWRs, PWRs, and CANDU power plants. Many of these fuel forms are only found in research reactors, or have military applications.

### Magnox fuel

A magnox fuel rod

Magnox reactors are pressurised, carbon dioxide cooled, graphite moderated reactors using natural uranium (i.e. unenriched) as fuel and magnox alloy as fuel cladding. Working pressure varies from 6.9 to 19.35 bar for the steel pressure vessels, and the two reinforced concrete designs operated at 24.8 and 27 bar. Magnox is also the name of an alloy—mainly of magnesium with small amounts of aluminium and other metals—used in cladding unenriched uranium metal fuel with a non-oxidising covering to contain fission products. Magnox is short for Magnesium non-oxidising. This material has the advantage of a low neutron capture cross-section, but has two major disadvantages:

• It limits the maximum temperature, and hence the thermal efficiency, of the plant.
• It reacts with water, preventing long-term storage of spent fuel under water.

Magnox fuel incorporated cooling fins to provide maximum heat transfer despite low operating temperatures, making it expensive to produce. While the use of uranium metal rather than oxide made reprocessing more straightforward and therefore cheaper, the need to reprocess fuel a short time after removal from the reactor meant that the fission product hazard was severe. Expensive remote handling facilities were required to address this danger.

### TRISO fuel

TRISO fuel particle which has been cracked, showing the multiple coating layers

Tristructural-isotropic (TRISO) fuel is a type of micro fuel particle. It consists of a fuel kernel composed of UOX (sometimes UC or UCO) in the center, coated with four layers of three isotropic materials. The four layers are a porous buffer layer made of carbon, followed by a dense inner layer of pyrolytic carbon (PyC), followed by a ceramic layer of SiC to retain fission products at elevated temperatures and to give the TRISO particle more structural integrity, followed by a dense outer layer of PyC. TRISO fuel particles are designed not to crack due to the stresses from processes (such as differential thermal expansion or fission gas pressure) at temperatures up to and beyond 1600°C, and therefore can contain the fuel in the worst of accident scenarios in a properly designed reactor. Two such reactor designs are the pebble bed reactor (PBR), in which thousands of TRISO fuel particles are dispersed into graphite pebbles, and the prismatic-block gas-cooled reactor (such as the GT-MHR), in which the TRISO fuel particles are fabricated into compacts and placed in a graphite block matrix. Both of these reactor designs are very high temperature reactors (VHTR) [formally known as the high-temperature gas-cooled reactors (HTGR)], one of the six classes of reactor designs in the Generation IV initiative.

TRISO fuel particles were originally developed in Germany for high-temperature gas-cooled reactors. The first nuclear reactor to use TRISO fuels was the AVR and the first powerplant was the THTR-300. Currently, TRISO fuel compacts are being used in the experimental reactors, the HTR-10 in China, and the HTTR in Japan.

RBMK reactor fuel rod holder 1 – distancing armature; 2 – fuel rods shell; 3 – fuel tablets.

### QUADRISO fuel

In QUADRISO particles a burnable neutron poison (europium oxide or erbium oxide or carbide) layer surrounds the fuel kernel of ordinary TRISO particles to better manage the excess of reactivity. If the core is equipped both with TRISO and QUADRISO fuels, at beginning of life neutrons do not reach the fuel of the QUADRISO particles because they are stopped by the burnable poison. After irradiation the poison depletes and neutrons streams into the fuel kernel of QUADRISO particles inducing fission reactions. This mechanism compensates fuel depletion of ordinary TRISO fuel. In the generalized QUADRISO fuel concept the poison can eventually be mixed with the fuel kernel or the outer pyrocarbon. The QUADRISO [3] concept has been conceived at Argonne National Laboratory.

'QUADRISO Particle

### RBMK fuel

RBMK reactor fuel was used in Soviet designed and built RBMK type reactors. This is a low enriched uranium oxide fuel. The fuel elements in an RBMK are 3 m long each, and two of these sit back-to-back on each fuel channel, pressure tube. Reprocessed uranium from Russian VVER reactor spent fuel is used to fabricate RBMK fuel. Following the Chernobyl accident, the enrichment of fuel was changed from 2.0% to 2.4%, to compensate for control rod modifications and the introduction of additional absorbers.

### CerMet fuel

CerMet fuel consists of ceramic fuel particles (usually uranium oxide) embedded in a metal matrix. It is hypothesized that this type of fuel is what is used in United States Navy reactors. This fuel has high heat transport characteristics and can withstand a large amount of expansion.

### Plate type fuel

ATR Core The Advanced Test Reactor at Idaho National Laboratory uses plate type fuel in a clover leaf arrangement. The blue glow around the core is known as Cherenkov radiation.

Plate type fuel has fallen out of favor over the years. Plate type fuel is commonly composed of enriched uranium sandwiched between metal cladding. Plate type fuel is used in several research reactors where a high neutron flux is desired, for uses such as material irradiation studies or isotope production, without the high temperatures seen in ceramic, cylindrical fuel. It is currently used in the Advanced Test Reactor (ATR) at Idaho National Laboratory.

### Sodium bonded fuel

Sodium bonded fuel consists of fuel that has liquid sodium in the gap between the fuel slug (or pellet) and the cladding. This fuel type is often used for sodium cooled liquid metal fast reactors. It has been used in EBR-I, EBR-II, and the FFTF. The fuel slug may be metallic or ceramic. The sodium bonding is used to reduce the temperature of the fuel.

## Spent nuclear fuel

Used nuclear fuel is a complex mixture of the fission products, uranium, plutonium and the transplutonium metals. In fuel which has been used at high temperature in power reactors it is common for the fuel to be heterogeneous; often the fuel will contain nanoparticles of platinum group metals such as palladium. Also the fuel may well have cracked, swollen and been used close to its melting point. Despite the fact that the used fuel can be cracked, it is very insoluble in water, and is able to retain the vast majority of the actinides and fission products within the uranium dioxide crystal lattice.

### Oxide fuel under accident conditions

Two main modes of release exist, the fission products can be vaporised or small particles of the fuel can be dispersed.

## Fuel behavior and post irradiation examination (PIE)

Materials in a high radiation environment (such as a reactor) can undergo unique behaviors such as swelling [4] and non-thermal creep. If there are nuclear reactions within the material (such as what happens in the fuel), the stoichiometry will also change slowly over time. These behaviors can lead to new material properties, cracking, and fission gas release:

• Fission gas release
• As the fuel is degraded or heated the more volatile fission products which are trapped within the uranium dioxide may become free. For example see J.Y. Colle, J.P. Hiernaut, D. Papaioannou, C. Ronchi, A. Sasahara, Journal of Nuclear Materials, 2006, 348, 229.
• Fuel cracking
• As the fuel expands on heating, the core of the pellet expands more than the rim which may lead to cracking. Because of the thermal stress thus formed the fuel cracks, the cracks tend to go from the center to the edge in a star-shaped pattern.

In order to better understand and control these changes in materials, these behaviors are studied. A common experiment to do this is post irradiation examination, in which fuel will be examined after it is put through reactor-like conditions [5][6] [7] [8]. Due to the intensely radioactive nature of the used fuel this is done in a hot cell. A combination of nondestructive and destructive methods of PIE are common.

The PIE is used to check that the fuel is both safe and effective. After major accidents, the core is normally subject to PIE in order to find out what happened. One site where PIE is done is the ITU which is the EU center for the study of highly radioactive materials.

In addition to the effects of radiation and the fission products on materials, scientists also need to consider the temperature of materials in a reactor, and in particular, the fuel. Too high a fuel temperature can compromise the fuel, and therefore it is important to control the temperature in order to control the fission chain reaction.

The temperature of the fuel varies as a function of the distance from the center to the rim. At distance x from the center the temperature (Tx) is described by the equation where ρ is the power density (W m−3) and Kf is the thermal conductivity.

Tx = TRim + ρ (rpellet2 - x2) (4 Kf)-1

To explain this for a series of fuel pellets being used with a rim temperature of 200 °C (typical for a BWR) with different diameters and power densities of 250 MW·m−3 have been modeled using the above equation. Note that these fuel pellets are rather large; it is normal to use oxide pellets which are about 10 mm in diameter.

 Temperature profile for a 20 mm diameter fuel pellet with a power density of 250 MW per cubic meter. Note the central temperature is very different for the different fuel solids. Temperature profile for a 26 mm diameter fuel pellet with a power density of 250 MW per cubic meter. Temperature profile for a 32 mm diameter fuel pellet with a power density of 250 MW per cubic meter. Temperature profile for a 20 mm diameter fuel pellet with a power density of 500 MW per cubic meter. Because the melting point of uranium dioxide is about 3300 K, it is clear that uranium oxide fuel is overheating at the center. Temperature profile for a 20 mm diameter fuel pellet with a power density of 1000 MW per cubic meter. The fuels other than uranium dioxide are not compromised.

Reference Radiochemistry and Nuclear Chemistry, G. Choppin, J-O Liljenzin and J. Rydberg, 3rd Ed, 2002, Butterworth-Heinemann, ISBN 0-7506-7463-6

## Radioisotope decay fuels

### Radioisotope battery

The terms atomic battery, nuclear battery and radioisotope battery are used interchangely to describe a device which uses the radioactive decay to generate electricity. These systems use radioisotopes that produce low energy beta particles or sometimes alpha particles of varying energies. Low energy beta particles are needed to prevent the production of high energy penetrating Bremsstrahlung radiation that would require heavy shielding. Radioisotopes such as tritium, nickel-63, promethium-147, and technetium-99 have been tested. Plutonium-238, curium-242, curium-244 and strontium-90 have been used.

There are two main categories of atomic batteries: thermal and non-thermal. The non-thermal atomic batteries, which have many different designs, exploit charged alpha and beta particles. These designs include the direct charging generators, betavoltaics, the optoelectric nuclear battery, and the radioisotope piezoelectric generator. The thermal atomic batteries on the other hand, convert the heat from the radioactive decay to electricity. These designs include thermionic converter, thermophotovoltaic cells, alkali-metal thermal to electric converter, and the most common design, the radioisotope thermoelectric generator.

### Radioisotope thermoelectric generators

A radioisotope thermoelectric generator (RTG) is a simple electrical generator which converts heat into electricity from a radioisotope using an array of thermocouples.

238
Pu
has become the most widely used fuel for RTGs. In the form of plutonium dioxide it has a half-life of 87.7 years, reasonable energy density and exceptionally low gamma and neutron radiation levels. Some Russian terrestrial RTGs have used 90
Sr
; this isotope has a shorter half-life and a much lower energy density, but is cheaper. Early RTGs, first built in 1958 by the U.S. Atomic Energy Commission, have used 210
Po
. This fuel provides phenomenally huge energy density, (a single gram of polonium-210 generates 140 watts thermal) but has limited use because of its very short half-life and gamma production and has been phased out of use in this application.

### Radioisotope heater units (RHU)

Photo of a disassembled RHU

Radioisotope heater units normally provide about 1 watt of heat each, derived from the decay of a few grams of plutonium-238. This heat is given off continuously for several decades.

Their function is to provide highly localised heating of sensitive equipment (such as electronics in outer space). The Cassini–Huygens orbiter to Saturn contains 82 of these units (in addition to its 3 main RTG's for power generation). The Huygens probe to Titan contains 35 devices.

## Fusion fuels

Fusion fuels include tritium (3H) and deuterium (2H) as well as helium-3 (3He). Many other elements can be fused together, but the larger electrical charge of their nuclei means that much higher temperatures are required. Only the fusion of the lightest elements is seriously considered as a future energy source. Although the energy density of fusion fuel is even higher than fission fuel, and fusion reactions sustained for a few minutes have been achieved, utilizing fusion fuel as a net energy source remains a theoretical possibility.[1]

### First generation fusion fuel

Deuterium and tritium are both considered first-generation fusion fuels; they are the easiest to fuse, because the electrical charge on their nuclei is the lowest of all elements. The three most commonly cited nuclear reactions that could be used to generate energy are:

2H + 3H $\rightarrow$ n (14.07 MeV) + 4He (3.52 MeV)
2H + 2H $\rightarrow$ n (2.45 MeV) + 3He (0.82 MeV)
2H + 2H $\rightarrow$ p (3.02 MeV) + 3H (1.01 MeV)

### Second generation fusion fuel

Second generation fuels require either higher confinement temperatures or longer confinement time than those required of first generation fusion fuels, but generate fewer neutrons. Neutrons are an unwanted byproduct of fusion reactions in an energy generation context, because they are absorbed by the walls of a fusion chamber, making them radioactive. They cannot be confined by magnetic fields, because they are not electrically charged. This group consists of deuterium and helium-3. The products are all charged particles, but there may be significant side reactions leading to the production of neutrons.

2H + 3He $\rightarrow$ p (14.68 MeV) + 4He (3.67 MeV)

### Third generation fusion fuel

Third generation fusion fuels produce only charged particles in the primary reactions, and side reactions are relatively unimportant. Since a very small amount of neutrons is produced, there would be little induced radioactivity in the walls of the fusion chamber. This is often seen as the end goal of fusion research. 3He has the highest Maxwellian reactivity of any 3rd generation fusion fuel. However, there are no significant natural sources of this substance on Earth.

3He + 3He $\rightarrow$ 2p + 4He (12.86 MeV)

Another potential aneutronic fusion reaction is the proton-boron reaction:

p + 11B → 34He

Under reasonable assumptions, side reactions will result in about 0.1% of the fusion power being carried by neutrons. With 123 keV, the optimum temperature for this reaction is nearly ten times higher than that for the pure hydrogen reactions, the energy confinement must be 500 times better than that required for the D-T reaction, and the power density will be 2500 times lower than for D-T.[citation needed]

## Notes

1. ^ "Nuclear Fusion Power". World Nuclear Association. 2009-09. Retrieved 2010-01-27.

## External links and references

### Fusion fuel

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• nuclear fuel — nuclear fuels N VAR Nuclear fuel is fuel that provides nuclear energy, for example in power stations …   English dictionary

• nuclear fuel — ► NOUN ▪ a substance that will undergo nuclear fission and can be used as a source of nuclear energy …   English terms dictionary

• Nuclear fuel — См. Ядерное топливо Термины атомной энергетики. Концерн Росэнергоатом, 2010 …   Термины атомной энергетики

• nuclear fuel — noun fuel (such as uranium) that can be used in nuclear reactors as a source of electricity • Hypernyms: ↑fuel * * * ˌnuclear ˈfuel [nuclear fuel] noun uncountable a substance that can be used as a source of ↑ …   Useful english dictionary

• nuclear fuel — branduolinis kuras statusas T sritis chemija apibrėžtis Medžiaga, kurioje vyksta branduolinės reakcijos ir atsipalaiduoja naudinga energija. atitikmenys: angl. nuclear fuel; reactor fuel rus. ядерное горючее …   Chemijos terminų aiškinamasis žodynas

• nuclear fuel — branduolinis kuras statusas Aprobuotas sritis branduolinė sauga apibrėžtis Specialioje konstrukcijoje esanti branduolinė medžiaga, skirta energijai branduoliniame reaktoriuje gaminti. atitikmenys: angl. nuclear fuel vok. Kernbrennstoff;… …   Lithuanian dictionary (lietuvių žodynas)

• nuclear fuel — atominis kuras statusas T sritis automatika atitikmenys: angl. nuclear fuel vok. Kernbrennstoff, m rus. ядерное топливо, n pranc. combustible nucléaire, m …   Automatikos terminų žodynas

• nuclear fuel — branduolinis kuras statusas T sritis fizika atitikmenys: angl. nuclear fuel vok. Kernbrennstoff, m rus. ядерное топливо, n pranc. combustible fissile, m; combustible nucléaire, m …   Fizikos terminų žodynas

• nuclear fuel — branduolinis kuras statusas T sritis apsauga nuo naikinimo priemonių apibrėžtis Branduolinė medžiaga, naudojama branduolinei energijai gaminti. atitikmenys: angl. nuclear fuel rus. ядерное топливо …   Apsaugos nuo naikinimo priemonių enciklopedinis žodynas

• nuclear fuel — branduolinis kuras statusas T sritis ekologija ir aplinkotyra apibrėžtis Medžiaga, naudojama branduolinei energijai gaminti. atitikmenys: angl. nuclear fuel vok. Kernbrennstoff, m rus. ядерное топливо, n …   Ekologijos terminų aiškinamasis žodynas

### Share the article and excerpts

##### Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.