Adiabatic shear band

Adiabatic shear band is a term used in physics, mechanics and engineering. Since the 1960s adiabatic shear bands have been studied extensively because of their importance as a failure mode in areas such as metal forming and cutting, various types of ballistic impact, as well as vehicle crashes.

An adiabatic shear band is one of the many mechanisms of failure that occur in metals and other materials that are deformed at a high rate in processes such as metal forming, machining and ballistic impact. ASBs are usually very narrow, typically 5 - 500μms and they consist of very highly sheared material.So what does the term ‘adiabatic’ mean? ‘Adiabatic’ is a thermodynamic term which literally means impassable and when used in relation to heat, it means an absence of heat transfer – the heat produced is retained in the zone where it is created. The opposite extreme is ‘isothermal’ here all the heat produced is conducted away.

It is necessary to include some basics of plastic deformation to understand the link between heat produced and the plastic work done. If we carry out a compression test on a
cylindrical specimen to, say, 50 % of its original height, the stress of the work material will increase usually significantly with reduction. This is called ‘work hardening’. During work hardening, the micro-structure, distortion of grain structure and the generation and glide of dislocations all occur. The remainder of the plastic work done – which can be as much as 90% of the total, is dissipated as heat.

If the plastic deformation is carried out under dynamic conditions, such as by drop forging, then the plastic deformation is localized more as the forging hammer speed is increased. This also means that the deformed material becomes hotter the higher the speed of the drop hammer. Now as metals become warmer, their resistance to further plastic deformation decreases. From this point we can see that there is a type of cascade effect: as more plastic deformation is absorbed by the metal, more heat is produced, making it easier for the metal to deform further. This is a catastrophic effect which almost inevitably leads to failure.

It appears that the first person to carry out any reported experimental programme to investigate the heat produced as a result of plastic deformation was Henri Tresca. These results were reported in a very long and useful paper in June 1878 in English.Tresca forged a bar of platinum (amongst many other metals); at the moment of forging the metal had just cooled down below red heat. The subsequent blow of the steam hammer, which left a depression in the bar and lengthened it, also reheated it in the direction of two lines in the form of a letter X. So great was this reheating, the metal along these lines was fully restored for some seconds to red heat. Tresca carried out many forging experiments on different metals. Tresca estimated the amount of plastic work converted into heat from a large number of experiments, and it was always above 70%.

ee also

References

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • adiabatic shear band — an adiabatic shear band is a narrow region, usually a few microns (micrometers) wide of intense plastic deformation that forms in high strain rate deformations of most metals, some polymers and several other material. Because of very little time… …   Mechanics glossary

  • band — adiabatic shear band …   Mechanics glossary

  • Kinetic energy penetrator — French anti tank round with its sabot APFSDS at point of separation o …   Wikipedia

  • climate — /kluy mit/, n. 1. the composite or generally prevailing weather conditions of a region, as temperature, air pressure, humidity, precipitation, sunshine, cloudiness, and winds, throughout the year, averaged over a series of years. 2. a region or… …   Universalium

  • solids, mechanics of — ▪ physics Introduction       science concerned with the stressing (stress), deformation (deformation and flow), and failure of solid materials and structures.       What, then, is a solid? Any material, fluid or solid, can support normal forces.… …   Universalium

  • Wind — For other uses, see Wind (disambiguation). Wind, from the …   Wikipedia

  • Cosmic microwave background radiation — CMB and Cosmic background radiation redirect here. For other uses see CMB (disambiguation) and Cosmic background (disambiguation). Physical cosmology …   Wikipedia

  • Abkürzungen/Luftfahrt/S–Z — Dies ist der fünfte Teil der Liste Abkürzungen/Luftfahrt. Liste der Abkürzungen Teil 1 A A Teil 2 B–D B; C; D Teil 3 E–K E; F; G; H; I; J; …   Deutsch Wikipedia

  • Saspo — Dies ist der fünfte Teil der Liste Abkürzungen/Luftfahrt. Liste der Abkürzungen Teil 1 A A Teil 2 B–D B; C; D Teil 3 E–K …   Deutsch Wikipedia

  • sound — sound1 soundable, adj. /sownd/, n. 1. the sensation produced by stimulation of the organs of hearing by vibrations transmitted through the air or other medium. 2. mechanical vibrations transmitted through an elastic medium, traveling in air at a… …   Universalium


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.