Bus manufacturing describes the
manufacturingof buses and coaches.
Bus manufacturing had its earliest origins in
carriagebuilding. Other bus manufacturers had their origins in truck manufacturing. Historically, bus chassis were shared between truck designs, but in later years specific bus chassis have been developed, and the midibussaw the introduction of a lighter weight bus chassis than normal trucks.
Bus manufacture historically developed as chassis and body builds. Often, large bus operators or authorities would maintain separate stocks of bus bodies, and would routinely refurbish buses in a central works, and refurbished chassis might receive a different body. One of the first integral type bus designs combining the body and chassis was the
Routemaster.In the 1980s many minibuses were built by applying bus bodies to van chassis, so called 'van derived' buses. Many of these have been replaced by purpose built designs, although for smaller minibuses this is still an option.
In several parts of the world, the bus is still a basic chassis, front-engined bonneted vehicle; however, where manufacturers have sought to maximise the
seating capacitywithin legal size constraints, the trend is towards rear and mid-engined designs.
In the 1990s, bus manufacture underwent major change with the push toward
low-floordesigns, for improved accessibility. Some smaller designs achieved this by moving the door behind the front wheels. On most larger buses, it was achieved with various independent front suspension arrangements, and kneeling technology, to allow an unobstructed path into the door and between the front wheel arches. Accordingly, these 'extreme front entrance' designs cannot feature a front mounted engined or mid-engined layout, and all use a rear-engined arrangement. Some designs also incorporate extendable ramps for wheelchair access.
Further accessibility is being achieved for high-floor coaches, whereby new designs are featuring built in
While the overwhelming majority of bus designs have been geared to
combustion enginepropulsion, accommodation has also been made for a variety of alternative drivelines and fuels, as in electric, fuel cell and hybrid bustechnologies. Some bus designs have also incorporated guidance technology.
Types of construction
There are three basic types of bus manufacturer:
* Chassis manufacturer - builds the underframe in a
* Body manufacturer - builds the
coachworka body-on-frametype construction
* Integral manufacturer - builds entire buses
Manufacturers may also be a combination of the above, offering chassis only or integral buses, or offering bodywork only as used on integral buses.
The splitting of body and chassis construction allows companies to specialise in two different fields. It also allows differing offerings of product to customers, who might prefer different chassis/body combinations. For the manufacturers it lessens the exposure if one or the other goes out of business. Larger operators may also split orders between different body/chassis combinations for shorter delivery schedules.
Sometimes, a chassis and body builder will offer an exclusive combination of one body on one chassis, as a 'semi-integral'. This combines the expertise of the two companies and saves the cost of making their chassis/body usable on different products.
Often builders, such as
Duple Metsecwill assemble products into kits, for export and local assembly at a partner site.
Large users of
transit buses, such as public transport authorities, may specify specific features that a bus design must feature. This practice was notable in the Transport for Londonbus specification, and predecessors.
The chassis combines:
* A structural underframe
* Engine and radiator
* Gearbox and transmission
* Wheels, axles and suspension
* Dashboard and steering wheel and driver's seat
Chassis will often be built as complete units, up to the point of being drive-able around the factory, or on the public highway to a nearby bodybuilder. The chassis will usually be front-engined, mid-engined or rear engined. Most chassis will mount the radiator at the front, irrespective of engine position, for more efficient cooling.
Chassis products will often be available in different standard lengths, even produced in articulated variants, and often be used for both bus and coach bodywork, such as the
Volvo B10M. The same chassis may even be used for single or double-decker busbodywork. Chassis builders may also offer different options for gearbox and engine suppliers. Chassis may also be built in multiple axle configuration.
The bus body builder will build the body onto the chassis. This will involve major consideration of:
* Staircase position/design (
* Number and position of doors
Bodywork is built for three general uses:
* Dual Purpose
Bus bodywork is usually geared to short trips, with many
transit busfeatures. Coach bodywork is for longer distance trips, with luggage racks and under-floor lockers. Other facilities may include toilets and televisions.
A dual purpose design is usually a bus body with upgraded coach style seating, for longer distance travel. Some exclusive coach body designs can also be available to a basic dual purpose fitment.
In past double-deck designs, buses were built to a low bridge design, due to overall height restrictions.
General design issues
Bus manufacturers have to have consideration for some general issues common to body, chassis or integral builders.
* Maximum weight (laden and unladen)
* Stability - often a
tilt testpass is required
* Maximum dimensions - length and width restrictions may apply
* Emissions standards
In the 1990s onwards, some bus manufacturers have moved towards making
transit businteriors more comparable to private cars, to encourage public transportridership. Other additions have seen multimedia and passenger informationsystems, and CCTVsystems. With these developments, bus designs have been increasing in weight, which is a concern for operators with the rising price of fuels in the 2000s.
Specialist builders may also produce bodies for executive,
sleeper bus, tour bus, airport busor school bususes, with special features for these uses. Builders may also adapt standard designs for these uses, and especially for paratransituse. In Israel, due to terroristattacks on buses, general bus builders have developed armoured buses, and are investigating controlled boarding systems. Armoured buses are also used for prisoner transport.
Several manufacturers and operators have invested in
articulated busdesigns, and even bi-articulated buses, to increase capacity without using two decks.
The use of different body and chassis manufacturers can mean one bus can have up to four identifying badges - the chassis maker and model, and the bodywork maker and model, making non-expert recognition difficult compared to the identification of other vehicles, such as cars. Operators may also paint over, or completely remove badges. This is further confused in
Transport in Malta, where the tradition of local modification has seen the wrong marques applied to buses. Several bus companies have changed ownership and name many times, leading to the same bus design receiving many different name badges, most notably Transbus International.
A further confusion can arise in the case where identical bodywork is applied to different chassis. This is sometimes truly identical, or only different in minor details. Mid-engined chassis designs are often identifiable by a mid mounted radiator and exhaust.
Radically different bus company liveries can cause problems in the application of a livery to a specific design. Many operators will apply a corporate design in the same way to any bus, leading to some odd sight lines. Some operators are more sympathetic, and tailor their liveries to the specific lines of each bus body design in use.
Rebuilds and modifications
Often, a bus builder will embark on a rebody program, such as the
East Lancs Greenway, where an existing chassis receives a new body to extend the usable life of the bus. Sometimes this is done by a manufacturer on a piecemeal basis, leading to odd one-off designs.
Sometimes, when a number of buses change hands, or operator requirements change, a bus builder may be required to refit them into the new owners preferred configuration. This can include adding/removing doors, or changing the destination display equipment to/from LED/dot-matrix/roller blind.
Some operators will rebuild a buses bodywork after superficial crash damage, or a bridge strike, again leading to odd one-off looking buses where the standard bodywork was not available. Bridge strike buses are often converted to
open top buses, or into single-decker bus. Older buses are often converted to shunters, tow trucks, tree-loppers, training buses or canteens.
Often, large operators with different types of buses will settle on a standard bus design for their fleet, to produce savings in maintenance and driver training. These operators may either sell off non-standard types, or consolidate them in one operating location.
Operators are often concerned with the ease of replacement of consumable items, such as bulbs, and easily damaged parts, such as the lower panels of the body, or windows. This is to maximise the time in service for its buses, although now builders will offer whole life servicing contracts.
Operators may also make decisions on a particular bus type or components based on the particular terrain operated in. Some hillier areas may select different drivetrain options. Areas with many low-bridges may have more single deckers than double deckers. Operators in humid climates may select air-conditioning as standard. A particular difficulty with double-deckers is trees striking the kerb-side top front corner. Manufacturers, or operators post delivery, may fit a
bull bartype arrangement to protect this part of the bodywork.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Bus — This article is about Road vehicles designed to carry passengers. For longer distance passenger vehicles, see Coach (vehicle). For other uses, see Bus (disambiguation). An Arriva double decker bus, running route 102 on the London Buses network … Wikipedia
Manufacturing — Part of a series of articles on Industry Manufacturing … Wikipedia
Manufacturing Commercial Vehicles — تصنيع المركبات التجارية Type Corporation Industry Automotive industry Founded 1994 Founder(s) Karim Ghabbour and Edzard Hans Wilhelm Reuter Headquarters … Wikipedia
Bus contention — Bus contention, in computer design, is an undesirable state of the bus in which more than one device on the bus attempts to place values on the bus at the same time. Most bus architectures require their devices follow an arbitration protocol… … Wikipedia
Manufacturing Automation Protocol — was a computer network standard released in 1982 for interconnection of devices from multiple manufacturers. It was developed by General Motors to combat the proliferation of incompatible communications standards used by suppliers of automation… … Wikipedia
Manufacturing Commercial Vehicles — MCV Corporate Group Manufacturing Commercial Vehicles تصنيع المركبات التجارية Rechtsform Sharikat al Mossahamah … Deutsch Wikipedia
Bus depots of the New York City Transit Authority — The sticker on this bus, below the MTA logo, indicates that it belongs to the West Farms Depot. The New York City Transit Authority (NYCTA) and its subsidiary, the Manhattan and Bronx Surface Transit Operating Authority (MaBSTOA), operates local… … Wikipedia
School bus — This article is about vehicles specifically designed and manufactured for carrying students to and from school. For information about school transportation in general, see student transport. School Bus Front 3/4 view of a typical North American… … Wikipedia
Mid Bus — Corporation Fate Acquired by Collins Industries (1998) Predecessor Superior Coach Company Founded 1981 Defunct 2008 Headquarters Lima, Ohio (1981 1995) Bluffton, Ohio (1995 2007) … Wikipedia
Transit bus — Urban bus route No. 1007 in Busan City Hall, Busan, South Korea. The model is Hyundai Universe Space Elegance … Wikipedia