A sway bar (also stabilizer bar, anti-sway bar, roll bar, or anti-roll bar, ARB) is an
automobilesuspension device. It connects opposite (left/right) wheels together through short leverarms linked by a torsion spring. A sway bar increases the suspension's roll stiffness—its resistance to roll in turns, independent of its spring rate in the vertical direction. The first stabilizer bar patent was awarded to S. L. C. Coleman of Fredericton, New Brunswickon April 22, 1919. [Mario Theriault, "Great Maritime Inventions 1833-1950", Goose Lane Editions, 2001, p. 69]
A sway bar is usually a
torsion springthat resists body roll motions. It is usually constructed out of a U-shaped piece of steel that connects to the body at two points, and at the left and right sides of the suspension. If the left and right wheels move together, the bar just rotates about its mounting points and does not bend. If the wheels move relative to each other, the bar is subjected to torsion and forced to twist.
The bar resists the torsion through its stiffness. The stiffness of an anti-roll bar is based on the fourth power of its diameter, the stiffness of the material, the inverse of the length of the lever arms (i.e., the shorter the lever arm, the stiffer the bar), the geometry of the mounting points, and the rigidity of the bar's mounting points. Some anti-roll bars, particularly those intended for use in
auto racing, are adjustable, allowing their stiffness to be altered by increasing or reducing the length of the lever arms. This permits the roll stiffness to be tuned for different situations without replacing the entire bar. The stiffer the bar, the more force required to move the left and right wheels relative to each other. This increases the amount of force required to make the body roll.
In a turn, the
sprung massof the vehicle's body produces a lateral force at the center of mass, proportional to lateral acceleration. Because the cg is usually not on the roll axis, the lateral force creates a moment about the roll axis that tends to roll the body. (The roll axis is a line that joins the front and rear roll centers (SAEJ670e). The moment is called the roll couple.
Roll couple is resisted by the suspension roll stiffness, which is a function of the spring rate of the vehicle's springs and of the anti-roll bars, if any. The use of anti-roll bars allows designers to reduce roll without making the suspension's springs stiffer in the vertical plane, which allows improved body control with less compromise of
One effect of body (frame) lean, for typical suspension geometry, is positive camber of the wheels on the outside of the turn and negative on the inside, which reduces their cornering grip (especially with cross ply tires).
Anti-roll bars provide two main functions:
The first function is the reduction of body lean. The reduction of body lean is dependent on the total roll stiffness of the vehicle. Increasing the total roll stiffness of a vehicle does not change the steady state total load (weight) transfer from the inside wheels to the outside wheels, it only reduces body lean. The total lateral load transfer is determined by the CG height and track width.
The other function of anti roll bars is to tune the high
g-force/ limit understeer behavior of the vehicle. The limit understeer behavior is tuned by changing the proportion of the total roll stiffness that comes from the front and rear axles. Increasing the proportion of roll stiffness at the front will increase the proportion of the total weight transfer that the front axle reacts and decrease the proportion that the rear axle reacts. This will cause the outer front wheel to run at a higher slip angle, and the outer rear wheel to run at a lower slip angle, which is an understeer effect. Increasing the proportion of roll stiffness at the rear axle will have the opposite effect and decrease understeer.
Because an anti-roll bar connects wheels on the opposite sides of the vehicle together, the bar will transmit the force of one-wheel bumps to the opposite wheel. On rough or broken pavement, anti-roll bars can produce jarring, side-to-side body motions (a "waddling" sensation), which increase in severity with the diameter and stiffness of the sway bars. Excessive roll stiffness, typically achieved by configuring an anti-roll bar too aggressively, will cause the inside wheels to lift off the ground during very hard cornering. This, of course, is only possible if the regular spring rate actually allows the outside wheels to handle the much increased load. This can be used to advantage, in fact many front wheel drive production cars will lift a wheel when cornering hard, in order to overload the other wheel on the axle, so limiting
Some high-priced cars, such as the
Range Rover Sportand BMW 7-series, have begun to use "active" anti-roll bars that can be proportionally controlled automatically by a suspension-control computer, reducing body lean in turns while improving rough-road ride quality. The firstFact|date=November 2007 to use this was the Citroen Xantia Activa, a medium sized sedan sold in Europe. The Activa system was an antiroll bar that could be stiffened under the command of the suspension ECU during hard cornering. The car rolled at any time at most 2 degrees. Mercedes S-class ABC system uses another approach, the computer uses sensors to detect lateral load, lateral force, height difference in the suspension strut and uses hydraulic pressure to raise or lower the spring to counter roll. This system removes the antiroll bar. Most active roll control systems allow a small degree of roll to give a more natural feel.
Torsion beam suspension
* [http://www.240edge.com/performance/tuning-bars.html Suspension tuning via sway bars]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Sway bar — (Vehicles) (a) A bar attached to the hounds, in the rear of the front axle, so as to slide on the reach as the axle is swung in turning the vehicle. (b) Either of the two bars used on couplong the oront ano rear sleds of a logging sled; also, the … The Collaborative International Dictionary of English
sway bar — noun An anti sway bar … Wiktionary
sway bar — noun Etymology: sway (II) 1. : a bar attached to the hounds in the rear of the front axle of a wagon so as to slide on the reach as the axle is swung in turning 2. : a steel bar placed near and parallel to an axle of an automotive vehicle to… … Useful english dictionary
sway bar — noun Date: 1949 a bar that torsionally couples the right and left front wheel suspensions of an automobile to reduce roll and sway … New Collegiate Dictionary
sway bar — A round bar which connects the left wheel suspension assembly with the right side. It may be found at the front and/or rear. Its main function is to keep both wheels rolling at the same rate when meeting bumps; but it also affects handling. A… … Dictionary of automotive terms
sway bar — Auto. See stabilizer bar. [1945 50] * * * … Universalium
anti-sway bar — [an΄tē swā′] n. ANTIROLL BAR * * * … Universalium
anti-sway bar — [an΄tē swā′] n. ANTIROLL BAR … English World dictionary
anti-sway bar — noun a connection between the left and right suspension systems of a road vehicle designed to stabilise it, and reduce roll or sway on corners Syn: anti roll bar … Wiktionary
anti-sway bar — /ænti ˈsweɪ ba/ (say antee sway bah) noun → anti roll bar … Australian English dictionary