Proximity effect (electron beam lithography)

The proximity effect in electron beam lithography (EBL) is the phenomenon that the exposure dose distribution, and hence the developed pattern, is wider than the scanned pattern, due to the interactions of the primary beam electrons with the resist and substrate. These cause the resist outside the scanned pattern to receive a non-zero dose.

Important contributions to weak resist polymer chain scission (for positive resists) or crosslinking (for negative resists) come from electron forward scattering and backscattering. The forward scattering process is due to electron-electron interactions which deflect the primary electrons by a typically small angle, thus statistically broadening the beam in the resist (and further in the substrate). The majority of the electrons do not stop in the resist but penetrate the substrate. These electrons can still contribute to resist exposure by scattering back into the resist and causing subsequent inelastic / exposing processes. This backscattering process originates e.g. from a collision with a heavy particle (i.e. substrate nucleus) and leads to wide angle scattering of the light electron from a range of depths (micrometres) in the substrate. The Rutherford backscattering probability increases quickly with substrate nuclear charge.

The above effects can be approximated by a simple two-gaussian model where a perfect point-like electron beam is broadened to a superposition of a gaussian with a width alpha of order 10's of nanometres due to forward scattering and a gaussian with a width eta of the order of a micrometers due to backscattering:

: PSF(r)=frac{1}{pi (1+eta)} [frac{1}{a^2} e^{-frac{r^2}{alpha^2 + frac{eta}{eta^2} e^{-frac{r^2}{b^2]

eta is of order 1 so the contribution of backscattered electrons to the exposure is of the same order as the contribution of 'direct' forward scattered electrons. alpha, eta and eta are determined by the resist and substrate materials and the primary beam energy. The two-gaussian model parameters, including the development process, can be determined experimentally by exposing shapes for which the gaussian integral is easily solved, i.e. donuts, with increasing dose and observing at which dose the center resist clears / does not clear.

A thin resist with a low electron density will reduce forward scattering. A light substrate (light nuclei) will reduce backscattering. When electron beam lithography is performed on substrates with 'heavy' films, such as gold coatings, the backscatter effect will (depending on thickness) significantly increase. Increasing beam energy will reduce the forward scattering width, but since the beam penetrates the substrate more deeply, the backscatter width will increase.

The primary beam can transfer energy to electrons via elastic collisions with electrons and via inelastic collision processes such as impact ionization. In the latter case, a secondary electron is created and the energy state of the atom changes, which can result in the emission of Auger electrons or X-rays. The range of these secondary electrons is an energy-dependent accumulation of (inelastic) mean free paths; while not always a repeatable number, it is this range (up to 50 nm) that ultimately affects the practical resolution of the EBL process. The model described above can be extended for these effects.


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Electron beam lithography — (often abbreviated as e beam lithography) is the practice of scanning a beam of electrons in a patterned fashion across a surface covered with a film (called the resist),cite book |last= McCord |first=M. A. |coauthors=M. J. Rooks |title=… …   Wikipedia

  • Proximity effect — may refer to: *Proximity effect (atomic physics) *Proximity effect (audio) * Proximity Effect (comic) *Proximity effect (electromagnetism) *Proximity effect (electron beam lithography) *Proximity effect (superconductivity) * The Proximity Effect …   Wikipedia

  • Extreme ultraviolet lithography — (also known as EUV or EUVL ) is a next generation lithography technology using the 13.5 nm EUV wavelength. EUVL opticsEUVL is a significant departure from the deep ultraviolet lithography used today. All matter absorbs EUV radiation. Hence, EUV… …   Wikipedia

  • Nanoimprint lithography — is a method of fabricating nanometer scale patterns. It is a simple nanolithography process with low cost, high throughput and high resolution. It creates patterns by mechanical deformation of imprint resist and subsequent processes. The imprint… …   Wikipedia

  • Optical proximity correction — An illustration of optical proximity correction. The blue Γ like shape is what we d like printed on the wafer, in green is the shape after applying optical proximity correction, and the red contour is how the shape actually prints (quite close to …   Wikipedia

  • X-ray lithography — is a next generation lithography that has been developed for the semiconductor industryref|vlad. Batches of microprocessors have already been produced. The short wavelengths of 0.8 nm X rays overcome diffraction limits in the resolution of… …   Wikipedia

  • Contact lithography — Contact lithography, also known as contact printing, is a form of photolithography whereby the image to be printed is obtained by illumination of a photomask in direct contact with a substrate coated with an imaging photoresist layer. Contents 1… …   Wikipedia

  • List of effects — This is a list of names for observable phenonema that contain the word effect, amplified by reference(s) to their respective fields of study. #*3D audio effect (audio effects)A*Accelerator effect (economics) *Accordion effect (physics) (waves)… …   Wikipedia

  • Elektronenstrahllithografie — Die Elektronenstrahllithografie (ESL, englisch electron beam lithography oft als e beam lithography abgekürzt) ist in der Mikro und Halbleitertechnik ein spezielles Verfahren zur Strukturierung einer Elektronenstrahl empfindlichen Schicht… …   Deutsch Wikipedia

  • Microelectromechanical systems — (MEMS) (also written as micro electro mechanical, MicroElectroMechanical or microelectronic and microelectromechanical systems) is the technology of very small mechanical devices driven by electricity; it merges at the nano scale into… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.