A snubber is a device used to suppress ("snub") voltage transients in electrical systems, pressure transients in fluid systems, or excess force or rapid movement in mechanical systems.
A snubber can be a mechanical device that limits pressure or velocity surges on measurement devices. These connect between the process and the measurement device allowing a relatively slow change in pressure or velocity to limit damage to the hardware. Such devices are common in industrial environments.
Snubbers are frequently used in electrical systems with an inductive load where the sudden interruption of current flow would lead to a sharp rise in
voltageacross the device creating the interruption. This sharp rise in voltage might lead to a transient or permanent failure of the controlling device. A spark is likely to be generated (arcing) and to cause electromagnetic interference. The snubber prevents this undesired voltage by conducting transient current around the device.
s. The voltage across a capacitor cannot change instantaneously, so a decreasing transient current will flow through it for a small fraction of a second, allowing the voltage across the switch to increase more slowly. While the values can be optimised for the application, a 100 ohm resistor in series with a 100 nanofarad capacitor of appropriate voltage rating is usually effective. This type of snubber is often manufactured as a single component.
When the current flowing is DC, a simple rectifier
diodeis often employed as another form of snubber. The snubber diode is wired in parallel with an inductive load (such as a relaycoil or electric motor). The diode is installed so that it does not conduct under normal conditions. When current to the inductive load is rapidly interrupted, a large voltage spike would be produced in the reverse direction (as the inductor attempts to keep current flowing in the circuit). This spike is known as an " inductive kick". Placing the snubber diode in inverse parallel with the inductive load allows the current from the inductor to flow through the diode rather than through the switching element, dissipating the energy stored in the inductive load over the series resistance of the inductor and the (usually much smaller) resistance of the diode (over-voltage protection). One disadvantage of simple rectifier diode used as a snubber is that the diode allows current to continue flowing, which may cause the relay to remain actuated for slightly longer; some circuit designs must account for this delay in the "dropping-out" of the relay.
More-sophisticated solid-state snubbers
In some dc circuits, a
varistoror two inverse-series Zener diodes (collectively called a transorb) may be used instead of the simple diode. Because these devices dissipate significant power, the relay may drop-out faster than it would with a simple rectifier diode. An advantage to using a transorb over just one diode however, is that it will protect against both over and under voltage if connected to ground, forcing the voltage to stay between the confines of the breakdown voltages of the Zener diodes. Just one Zener diode connected to ground will only protect against positive transients.
In ac circuits a rectifier diode snubber cannot be used; if a simple RC snubber is not adequate a more complex bidirectional snubber design must be used.
Transient voltage suppression diode
Wikimedia Foundation. 2010.
Look at other dictionaries:
Snubber — Das aus dem technischen Englisch stammende Wort Snubber umschreibt eine Einrichtung zur Dämpfung unerwünschter Schwingungen in technischen Anwendungen. Am häufigsten wird der Begriff in der Elektronik verwendet. Snubber können aber auch… … Deutsch Wikipedia
snubber — i. A component in a hydraulic or pneumatic actuator that slows down the motion of the piston toward the end of its travel and thus cushions the stopping action of the piston. ii. A restrictor fitting installed between an oil pressure gauge and… … Aviation dictionary
snubber — noun Date: 1853 1. one that snubs 2. shock absorber … New Collegiate Dictionary
snubber — See snub. * * * … Universalium
snubber — noun a) A device used to suppress ( snub ) voltage transients in electrical systems, pressure transients in fluid systems, or excess force or rapid movement in mechanical systems … Wiktionary
snubber — a generic term which is commonly applied to mechanisms which employ dry friction to produce damping of suspension systems … Mechanics glossary
snubber — n. one who snubs, one who treats another contemptuously, one who purposefully ignores … English contemporary dictionary
snubber — noun 1》 a simple kind of shock absorber. 2》 an electric circuit intended to suppress voltage spikes … English new terms dictionary
snubber — snub·ber … English syllables
snubber — See bump stop … Dictionary of automotive terms