Multiplexed display

An entirely-typical multiplexed vacuum fluorescent display used in a videocassette recorder

Multiplexed displays are electronic displays where the entire display is not driven at one time. Instead, sub-units of the display (typically, rows or columns for a dot matrix display or individual characters for a character orientated display, occasionally individual display elements) are multiplexed, that is, driven one at a time, but the electronics and the persistence of vision combine to make the viewer believe the entire display is continuously active.

A multiplexed display has several advantages compared to a non-multiplexed display:

  • Fewer wires (often, far fewer wires) are needed
  • Simpler driving electronics can be used
  • And both lead to reduced cost
  • Reduced power consumption

Multiplexed displays can be divided into two broad categories:

  • Character-oriented displays
  • Pixel-oriented displays

Contents

Character-oriented displays

Most character-oriented displays (such as seven-segment displays, fourteen-segment displays, and sixteen-segment displays) display an entire character at one time. The various segments of each character are connected in a two-dimensional matrix and will only illuminate if both the "row" and "column" lines of the matrix are at the correct electrical potential. The light-emitting element normally takes the form of a diode so electricity will only flow in one direction, keeping the individual "row" and "column" lines of the matrix electrically isolated from each other. For liquid crystal displays, the intersection of the row and column is not conductive at all.

In the example of the VCR display shown above, the illuminated elements are the plates of many individual triode vacuum tubes sharing the same vacuum enclosure. The grids of the triodes are arranged so that only one digit is illuminated at a time. All of the similar plates in all of the digits (for example, all of the lower-left plates in all of the digits) are connected in parallel. One by one, the microprocessor driving the display enables a digit by placing a positive voltage on that digit's grid and then placing a positive voltage on the appropriate plates. Electrons flow through that digit's grid and strike those plates that are at a positive potential.

If the display had been built with every segment being individually connected, the display would have required 49 wires just for the digits, with more wires being needed for all of the other indicators that can be illuminated. By multiplexing the display, only seven "digit selector" lines and seven "segment selector" lines are needed. The extra indicators (in our example, "VCR", "Hi-Fi", "STEREO", "SAP", etc.) are arranged as if they were segments of an additional digit or two or extra segments of existing digits and are scanned using the same multiplexed strategy as the real digits.

A few character-oriented displays drive only one segment at a time. The display on the Hewlett-Packard HP-35 was an example of this. The calculator took advantage of an effect where very brief pulses of light are perceived as brighter than a longer pulse of light with the same time-integral of intensity.

Pixel-oriented displays

By comparison, in dot matrix displays, individual pixels are located at the intersections of the matrix's "row" and "column" lines and each pixel can be individually controlled.

Here, the savings in wiring becomes far more dramatic. For a typical 1024x768 (XGA) computer screen, 786,433 wires would be needed for non-multiplexed control. That many wires would be completely impractical. But by arranging the pixels into a multiplexed matrix, only 1792 wires are needed; a completely practical situation.

Pixel-oriented displays may drive a single pixel at a time or an entire row or column of pixels simultaneously. Active-matrix liquid crystal displays provide a storage element at each pixel so that the pixel continues to display the correct state even when not being actively driven.

"Break up"

Because most multiplexed displays do not present the entire display simultaneously, they are subject to "break up" if the observer's point of regard is in motion. For example, if the observer were to rapidly swing their vision across a multiplexed display, they might see a jumble of individual digits rather than a coherent display. This effect can also sometimes be provoked by chewing hard candy; this causes vibration of the user's eyes, leading to the break-up of the display.

The multiplexed nature of a display can also be revealed by observing it through a mechanical stroboscope, for example, a spinning slotted wheel.

External links

See also


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Seven-segment display — A typical 7 segment LED display component, with decimal point. A seven segment display (SSD), or seven segment indicator, is a form of electronic display device for displaying decimal numerals that is an alternative to the more complex dot matrix …   Wikipedia

  • Vacuum fluorescent display — A vacuum fluorescent display (VFD) is a display device used commonly on consumer electronics equipment such as video cassette recorders, car radios, and microwave ovens. Unlike liquid crystal displays, a VFD emits a very bright light with clear… …   Wikipedia

  • Volumetric display — A volumetric display device is a graphical display device that forms a visual representation of an object in three physical dimensions, as opposed to the planar image of traditional screens that simulate depth through a number of different visual …   Wikipedia

  • Field Emission Display — (FED) désigne une technique d affichage destinée aux écrans plats. Cette technique a été principalement développée par Sony jusqu en 2009 puis abandonnée au profit des OLED. Les brevets sont détenus depuis janvier 2010 par AU Optronics qui espère …   Wikipédia en Français

  • Surface-conduction Electron-emitter Display — Pour les articles homonymes, voir Surface (homonymie). Surface conduction Electron emitter Display (SED) désigne une technologie d affichage destinée aux écrans plats, développée conjointement par Canon et T …   Wikipédia en Français

  • Multiplexing — General multiplex scheme: the ν input lines channels are multiplexed into a single fast line. The demultiplexer receives the multiplexed data stream and extracts the original channels to be transferred …   Wikipedia

  • Charlieplexing — is a technique proposed in early 1995 by Charlie Allen at Maxim Integrated Products for driving a multiplexed display in which relatively few I/O pins on a microcontroller are used to drive an array of LEDs. The method utilizes the tri state… …   Wikipedia

  • Oscilloscope — This article is about current oscilloscopes, providing general information. For history of oscilloscopes, see Oscilloscope history. For detailed information about various types of oscilloscopes, see Oscilloscope types. Illustration showing the… …   Wikipedia

  • Keyboard technology — Keyboard construction, in four layers, of a typical notebook computer keyboard There are many types of keyboards, usually differentiated by the switch technology employed in their operation. Keyboards are defined by the number (usually about… …   Wikipedia

  • Subtitle (captioning) — For other uses, see Subtitle. Part of a series on Translation Types …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.