Stamp vending machine

A stamp vending machine (SVM) is a mechanical, electrical or electro-mechanical device which can be used to automatically vend postage stamps to users in exchange for a pre-determined amount of money, normally in coin. Most SVMs were positioned in public places to provide a useful service to customers when other sources of postage stamps, such as Post Offices were closed. The term is often applied to the entire object as found attached to a pillar box or sited in a wall. The name Stamp Vending Machine only applies to the internal mechanism, the housing is described by the UK Post Office as a "case" and was supplied, installed and maintained separately. Many postal administrations around the world have used automatic stamp vending machines including the USA, where private manufacturers began vending stamps from coils in 1908. Most countries of the Commonwealth of Nations have issued stamps for use in Stamp Vending Machines, including Hong Kong, New Zealand and Malta.

tamp Vending Machines in the UK

Early Designs

In the UK, the earliest SVM was tested in the last years of the 19th Century, but there are no drawings or records appertaining to it and it was quickly withdrawn. The earliest production series machines were introduced under Edward VII in 1907 following experiments with a patented 1906 design by New Zealander Robert J Dickie which was demonstrated to the British House of Lords in 1907. Dickie licenced the sales rights to his new machine outside the British Empire to Kermode & Co, who successfully sold it around the world. SVM mechanisms and cases are described by the UK Post Office using, rather confusingly, two separate alphabetical series of type letters to describe each one. Thus a machine may be described in the format of a "Type B4 mechanism in a Case Type K".

The earliest ‘A’ type vending machine was completely mechanical, deriving power to drive the vending mechanism from the insertion of a suitable coin. Initially the machines were set to dispense only ½d and 1d stamps. These proved to be quite successful and were in continuous production until 1924, when the improved Type ‘B’ machine was introduced. Type A machines feature elaborate cast brass fronts with the coin value raised against a chequer-plate design in the casting. Type ‘B’ could accept ½ d, 1d or (later) 3d coins and would in exchange, vend a single stamp from a coil stamp roll joined vertically (IE head-to-tail). A number after the letter B denotes a particular pattern or variation in design for the machine. The coin value is indicated on a changeable metal plate near the coin slot as the value and coin size were now variable at the time of manufacture, but not once deployed in the field.

New types Introduced

Following quickly from the Type’B’ designs came other combinations of coin-operated machine. In Type ‘C’, two ½d stamps were issued in exchange for one penny coin, whilst in Type ‘D’, one 2d stamp is vended in exchange for two penny coins. These four types all work with long continuous stamp coils. In Type ‘F’, the machine is set to dispense booklets of stamps. These were introduced for machine-vending shortly before the outbreak of World War II and eventually came to be the predominant type in use. Booklets were first tried out in 1935 as mixed-value booklets of King George V Jubilee stamps in panes of four, interleaved with advertising. These Jubilee books were too large for machine vending at the time.

Heyday of the Stamp Vending Machine

By 1970, there were some 50000 stamp selling machines in use in the UK and many more had been exported worldwide. The basic design remained unchanged from 1905 until 1970, when the Type ‘G’ series was introduced. G.1 was the first “modern” mechanism and was said by the manufacturer to be designed to fit in the old housings, although subsequent to the prototype it had to be modified and in any case was much deeper than the preceding designs so that it actually required its own specially designed case, designated Type U. Type G machines incorporated many novel features including a Perspex cover sealed from moisture over the stamp coil to prevent the stamps sticking together. In addition the mechanism was driven by the user lifting a large flap over the vend slot. This action primed the machine. It could be set to dispense any number of stamps from one to five against the insertion of a single coin, although in practice this was never done and all Type G machines vended a strip of five values. Initially these added up to 1 shilling, then after 1971, 5 new pence and by 1980, 10p. Changes in postal rates introduced in 1980 meant that all surviving 10p machines were withdrawn from service.

Construction & Use

Types A-E share the same common features that contributed to their success; they all have a stamp feed wheel with pins which accurately interlock with the stamp perforations and they all derive the energy needed to operate the mechanism from the raising of a weight through the insertion of a coin. Type F machines are different in that the coin releases a “Pull” bar which when pulled, forces the next booklet in a stack out through the vend slot. Such mechanisms as Type F and Type G are said to be “coin-freed”. This proved to be very successful and was used over and over again in subsequent designs of machine up to about 1988, when manufacture of purely mechanical SVMs ceased.

From that time all machines in use in the UK were of the electro-mechanical type. This used a standard mechanical coin-weigher unit and mechanical stacking for booklets, but had an electronic arm on a rotating cam for dispensing the booklets. They were manufactured by Hillday Automation of Attleborough, Norfolk and designated Type B52. Two versions were built with either long or short coin boxes, easily recognised from the length of the case. Initially set to dispense 4 x 25p stamps in a folded booklet in exchange for a £1 coin, different combinations were later employed as postage rates in the UK continued to rise.

These electro-mechanical machines were powered by large internal battery packs which made them expensive to service and more unreliable than the purely mechanical designs. All of these were removed during 2001 and today there are far fewer automated stamp vending machines in use in the UK. As stamp booklets can now be widely purchased from supermarkets, garages, kiosks and newsagents, demand for automatic vending facilities has declined to the point where their continued operation becomes un-economic. Remaining machines are also found inside Post Offices, dispensing 1st and 2nd class NVI stamps from coils for those customers who wish to avoid queues.

Official Documents

In 1949, the GPO were issuing Type B4 machines in 1/2d and 1d denominations, while by 1958 a B4 3d machine had been introduced. P.O. Engineering Dept. notice C.1003 was issued on 22 September 1949, which includes ink drawings to show how the B4 mechanism works. [P.O. Engineering Dept notice C.1003, 22 September 1949.] Notice C4111 details how to load it, while maintenance is covered by C5011 & C5164. These documents can be viewed at The British Postal Museum & Archive in London. [Notice C4111.] [Notice C5011.] [Notice C5164.]

References


*
*
*

External links

* [http://www.postalheritage.org.uk/ British Postal Museum & Archive]
* [http://www.lbsg.org/ The Letter Box Study Group]
* [http://www.cvphm.org/SVM.html The Colne Valley Postal History Museum]
* [http://www.nzedge.com/heroes/dickie.html Robert J Dickie - Champion of Automation]
* [http://www.earsathome.com/coils.html Coil and booklet stamps of Great Britain]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • stamp vending machine — (SVM) A vending machine that has multiple modules capable of dispensing varying quantities of stamps from a coil from each module …   Glossary of postal terms

  • Vending machine — A vending machine made in 1952. A Best Buy Express vending m …   Wikipedia

  • Postage stamp — A postage stamp is an adhesive paper evidence of pre paying a fee for postal services. Usually a small paper rectangle or square that is attached to an envelope, the postage stamp signifies that the person sending the letter or package may have… …   Wikipedia

  • Coil stamp — This 2 cent coil stamp of the US 1954 Liberty series was used heavily throughout the 1950s and 60s. A coil stamp is a type of postage stamp sold in strips one stamp wide. The name derives from the usual handling of long strips, which is to coil… …   Wikipedia

  • Ticket machine — A ticket machine is a vending machine that produces tickets. For instance, ticket machines dispense train tickets at railway stations and tram tickets at some tram stops and in some trams. The typical transaction consists of a user using the… …   Wikipedia

  • SVM — stamp vending machine (SVM) A vending machine that has multiple modules capable of dispensing varying quantities of stamps from a coil from each module …   Glossary of postal terms

  • United States Postal Service — This article is about the government agency. For individual post offices, see U.S. Post Office (disambiguation). For the cycling team, see Discovery Channel Pro Cycling Team. USPS redirects here. For the non profit boating safety and education… …   Wikipedia

  • Pillar box — A pillar box is a free standing post box, in the United Kingdom, where mail is deposited to be collected by the Royal Mail and forwarded to the addressee. Similar designs exist as historical artefacts in certain Commonwealth of Nations countries …   Wikipedia

  • Postage stamps and postal history of New Zealand — Postage stamps have been issued in New Zealand since around the 18th to 20th of July 1855 with the Chalon head stamps figuring Queen Victoria. The design was based on a full face portrait of the Queen in her state robes at the time of her… …   Wikipedia

  • List of philatelic topics — This is a list of philatelic topics. compactTOC NOTOC A Acknowledgement of receipt Aerogram Aerophilately Affixing machine Airmail Airmail etiquette Arrow block Astrophilately Philatelic auction Philatelic auction catalogB Balloon mail Bicycle… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.