An uncoiled modern watch mainspring.
Clock mainspring

A mainspring is a spiral torsion spring of metal ribbon that is the power source in mechanical watches and some clocks. Winding the timepiece, by turning a knob or key, stores energy in the mainspring by twisting the spiral tighter. The force of the mainspring then turns the clock's wheels as it unwinds, until the next winding is needed. The adjectives wind-up and spring-wound refer to mechanisms powered by mainsprings, which also include kitchen timers, music boxes, wind-up toys and clockwork radios.


Modern mainsprings

Elgin pocketwatch mainsprings from around 1910, showing (l-r): spiral, semi-reverse, reverse.

A modern watch mainspring is a long strip of hardened and blued steel, or specialised steel alloy, 20-30 centimeters long and 0.05-0.2 millimeters thick. The mainspring in the common 1-day movement is calculated to enable the watch to run for 36 to 40 hours, i.e. with a power-reserve for 12 to 16 hours, which is the normal standard for hand-wound as well as self-winding watches. 8-Day movements provide power for at least 192 hours but use longer mainsprings and bigger barrels. Clock mainsprings are similar, only larger.

Since 1945, carbon steel alloys have been increasingly superseded by newer special alloys (iron, nickel and chromium with the addition of cobalt, molybdenum, or beryllium), and also by cold-rolled alloys ('structural hardening'). Known to watchmakers as 'white metal' springs (as opposed to blued carbon steel), these are stainless and have a higher elastic limit. They are less subject to permanent bending (becoming 'tired') and there is scarcely any risk of their breaking. Some of them are also practically non-magnetic.

In their relaxed form, mainsprings can have three distinct shapes:

  • Spiral coiled: i.e. coiled in the same direction throughout, viz. that of a spring inside the barrel
  • Semi-reverse: The outer end of the spring is coiled in the reverse direction to form an angle less than 360 degrees.
  • Reverse (resilient): the outer end of the spring is coiled in the reverse direction to form an angle exceeding 360 degrees.

The reverse coils provide extra force at the end of the running period, in order to keep the timepiece running at a constant rate to the end.

How they work

Cross section of a going barrel in a watch (mainspring fully wound).
Going barrel of a watch

The mainspring is coiled around an axle called the arbor, with the inner end hooked to it. In many clocks, the outer end is attached to a stationary post. The spring is wound up by turning the arbor, and after winding its force turns the arbor the other way to run the clock. The disadvantage of this arrangement is that while the mainspring is being wound, its drive force is removed from the clock movement, so the clock may stop. The winding mechanism must always have a ratchet attached, with a pawl (called by clockmakers the click) to prevent the spring from unwinding.

In the form used in modern watches, called the going barrel, the mainspring is coiled around an arbor and enclosed inside a cylindrical box called the barrel which is free to turn. The spring is attached to the arbor at its inner end, and to the barrel at its outer end. The attachments are small hooks or tabs, which the spring is hooked to by square holes in its ends, so it can be easily replaced.

The mainspring is wound by turning the arbor, but drives the watch movement by the barrel; this arrangement allows the spring to continue powering the watch while it is being wound. Winding the watch turns the arbor, which tightens the mainspring, wrapping it closer around the arbor. The arbor has a ratchet attached to it, with a click to prevent the spring from turning the arbor backward and unwinding. After winding, the arbor is stationary and the pull of the mainspring turns the barrel, which has a ring of gear teeth around it. This meshes with one of the clocks gears, usually the center wheel pinion and drives the wheel train. The barrel usually rotates once every 8 hours, so the common 40 hour spring requires 5 turns to unwind completely.


The mainspring contains a lot of energy. Clocks and watches have to be disassembled periodically for maintenance and repair, and if precautions are not taken the spring can release suddenly, causing serious injury. Mainsprings are 'let down' gently before servicing, by pulling the click back while holding the winding key, allowing the spring to slowly unwind. However, even in their 'let down' state, mainsprings in barrels contain dangerous residual tension. Watchmakers and clockmakers use a tool called a "mainspring winder" to safely install and remove them. Large mainsprings in clocks are immobilized by "mainspring clamps" before removal.


Mainsprings appeared in the first spring powered clocks, in 15th century Europe. Around 1400 coiled springs began to be used in locks,[1] and many early clockmakers were also locksmiths. Springs were applied to clocks to make them smaller and more portable than previous weight driven clocks, evolving into the first pocketwatches by 1600. Many sources erroneously credit the invention of the mainspring to the Nürnberg clockmaker Peter Henlein (also spelled Henle, or Hele) around 1511.[2][3][4] However, many descriptions from the 15th century of portable clocks 'without weights', and at least two surviving examples, show that spring driven clocks existed by the early years of that century.[1][5][6] The oldest surviving clock powered by a mainspring is the Burgunderuhr (Burgundy Clock), an ornate, gilt spring driven chamber clock, currently at the Germanisches Nationalmuseum in Nurnberg, whose iconography suggests that it was made around 1430 for Philippe the Good, Duke of Burgundy.[1]

The first mainsprings were made of steel without tempering or hardening processes. They didn't run very long, and had to be wound twice a day. Henlein was noted for making watches that would run 40 hours between windings.

Constant force from a spring

Torque curve of a mainspring. The force it provides decreases linearly as it unwinds.
Torque curves of mainsprings in going barrels (1879). The flatter central section provides more constant force during the running period, allowing the clock movement to keep better time.

A problem throughout the history of spring driven clocks and watches is that the force (torque) provided by a spring is not constant, but diminishes as the spring unwinds (see graph). Timepieces, however, have to run at a constant rate to keep accurate time. Timekeeping mechanisms are never isochronous; meaning their rate is affected by changes in the drive force. This was especially true of the primitive verge and foliot type used before the advent of the balance spring in 1657. So early clocks slowed down as the mainspring ran down.

Two solutions to this problem appeared in the early spring powered clocks in the 15th century: the stackfreed and the fusee. The stackfreed was an eccentric cam mounted on the mainspring arbor, with a spring-loaded roller that pressed against it. The cam was shaped so that early in the running period when the mainspring was pushing strongly, the stackfreed would provide an opposing force, while later when the mainspring was almost run down and pushing weakly, it would provide a helping force. The stackfreed added a lot of friction and probably reduced a clock's running time substantially; it was rarely used and was abandoned after about a century.

The fusee was a much longer lasting innovation. This was a cone-shaped pulley that was turned by a chain wrapped around the mainspring barrel. Its curving shape continuously changed the mechanical advantage of the linkage to even out the force of the mainspring as it ran down. Fusees became the standard method of getting constant torque from a mainspring. They were used in most spring driven clocks and watches from their first appearance until the 19th century when the going barrel took over, and in marine chronometers until the 1970s.

Another early device which helped even out the spring's force was stopwork or winding stops, which prevented the mainspring from being wound up all the way, and prevented it from unwinding all the way. The idea was to use only the central part of the spring's 'torque curve', where its force was more constant. The most common form was the Geneva stop or 'Maltese cross'. Stopwork isn't needed in modern watches.

A fourth device used in a few precision timepieces was the remontoire. This was a small secondary spring or weight which powered the timepiece's escapement, and was itself rewound periodically by the mainspring. This isolated the timekeeping element from the varying mainspring force.

16th century pocketwatch movement with stackfreed (near top).

The modern going barrel, invented in 1760 by Jean-Antoine Lépine, produces a constant force by simply using a longer mainspring than needed, and coiling it under tension in the barrel. In operation, only the inner turns of the spring are used. Mathematically, the tension creates a 'flat' section in the spring's 'torque curve' (see graph at right) and only this flat section is used. In addition, the outer end of the spring is often given a 'reverse' curve, so it has an 'S' shape. This stores more tension in the spring's outer turns where it is available toward the end of the running period. The result is that the barrel provides approximately constant torque over the watch's designed running period; the torque doesn't decline until the mainspring has almost run down.

The built-in tension of the spring in the going barrel makes it hazardous to disassemble even when not wound up.

Broken mainsprings

Because they are subjected to constant stress cycles, up until the 1960s mainsprings generally broke from metal fatigue long before other parts of the timepiece. They were considered expendable items.[7] This often happened at the end of the winding process, when the spring is wound as tightly as possible around the arbor, with no space between the coils. When manually winding, it is easy to reach this point unexpectedly and put excessive pressure on the spring. Broken mainsprings were the largest cause of watch repairs until the 1960s.[8] Since then, the improvements in spring metallurgy mentioned above have made broken mainsprings rare.

Even if the spring didn't break, too much force caused another problem, called 'knocking' or 'banking'.[9][10] Since no more slack was left in the spring, the pressure of the last turn of the winding knob put the spring under excessive tension, which was locked in by the last click of the ratchet. So the watch ran with excessive drive force for several hours, until the extra tension in the end of the spring was relieved. This made the balance wheel rotate too far in each direction, causing the impulse pin on the wheel to knock against the back of the fork horns. This caused the watch to gain time, and could break the impulse pin. In older watches this was prevented with 'stopwork'. In modern watches this is prevented by designing the 'click' with some 'recoil' (backlash), to allow the arbor to rotate backward after winding by about two ratchet teeth, enough to remove excess tension.

Motor or safety barrel

Around 1900, when broken watchsprings were more of a problem, some pocketwatches used a variation of the going barrel called the motor barrel or safety barrel. Mainsprings usually broke at their attachment to the arbor, where bending stresses are greatest. When the mainspring broke, the outer part recoiled and the momentum spun the barrel in the reverse direction. This applied great force to the delicate wheel train and escapement, often breaking pivots and jewels.

In the motor barrel, the functions of the arbor and barrel were reversed from the going barrel. The mainspring was wound by the barrel, and turned the arbor to drive the wheel train. Thus if the mainspring broke, the destructive recoil of the barrel would be applied not to the wheel train but to the winding mechanism, which was robust enough to take it.

Safety pinion

A safety pinion was an alternate means of protection, used with the going barrel. In this, the center wheel pinion, which the barrel gear engages, was attached to its shaft with a reverse screw thread. If the spring broke, the reverse recoil of the barrel, instead of being passed on to the gear train, would simply unscrew the pinion.

The myth of 'overwinding'

Watches are often found stopped with the mainspring fully wound, which led to a myth that winding a watch all the way up damages it.[citation needed] What actually happens is that as time passes and the watch movement collects dirt and the oil dries up, friction increases, so that the mainspring doesn't have the force to turn the watch until the end of its normal running period, and it stops prematurely. If the owner continues to wind and use the watch without servicing, eventually the friction force reaches the 'flat' part of the torque curve, and quickly a point is reached where the mainspring doesn't have the force to run the watch even at full wind, so the watch stops with the mainspring fully wound. The watch needs service, but the problem is caused by a dirty movement or other defect, not 'overwinding'.

Self-winding watches and 'unbreakable' mainsprings

The mainspring of an automatic watch. The spring isn't firmly mounted on the left side, and will slip when fully wound.

Self-winding or automatic watches, introduced widely in the 1950s, use the natural motions of the wrist to keep the mainspring wound. A semicircular weight, pivoted at the center of the watch, rotates with each wrist motion. A winder mechanism uses rotations in both directions to wind the mainspring.

In automatic watches, motion of the wrist could continue winding the mainspring until it broke. This is prevented with a slipping clutch device.[11] The outer end of the mainspring, instead of attaching to the barrel, is attached to a circular expansion spring called the bridle that presses against the inner wall of the barrel, which has serrations or notches to hold it. During normal winding the bridle holds by friction to the barrel, allowing the mainspring to wind. When the mainspring reaches its full tension, its pull is stronger than the bridle. Further rotation of the arbor causes the bridle to slip along the barrel, preventing further winding. In watch company terminology, this is often misleadingly referred to as an 'unbreakable mainspring'[citation needed].

'Tired' or 'set' mainsprings

After decades of use, mainsprings in older timepieces are found to deform slightly and lose some of their force, becoming 'tired' or 'set'. This condition is mostly found in springs in barrels. It causes the running time between windings to decrease. During servicing the mainspring should be checked for 'tiredness' and replaced if necessary. The British Horological Institute suggests these tests[12]:

  • In a mainspring barrel, when unwound and relaxed, most of a healthy spring's turns should be pressed flat against the wall of the barrel, with only 1 or 2 turns spiralling across the central space to attach to the arbor. If more than 2 turns are loose in the center, the spring may be 'tired'; with 4 or 5 turns it definitely is 'tired'.
  • When removed from the barrel, if the diameter of the relaxed spring lying on a flat surface is less than 2½ times the barrel diameter, it is 'tired'.

Power reserve indicator

The power reserve is at the 6 position on this automatic watch. Here it is indicating that 25 out of 40 hours remain

Some high grade watches have an extra dial on the face indicating how much power is left in the mainspring, often graduated in hours the watch has left to run. Since both the arbor and the barrel turn, this mechanism requires a differential gear that measures how far the arbor has been turned, compared to the barrel.

Unusual forms of mainspring

A mainspring is usually a coiled metal spring, however there are exceptions:

  • The wagon spring clock: During a brief time in American clockmaking history coilable spring steel was not available in the USA and inventive clockmakers built clocks powered by a stack of leafsprings, similar what has traditionally served as a suspension spring for wagons.
  • Other spring types are conceivable and have been used occasionally on experimental timepieces, such as e.g. torsion springs.
  • Occasionally one finds an odd clock with a spring made of material other than metal, such as e.g. synthetic elastic materials.


External links


  1. ^ a b c White, Lynn Jr. (1966). Medieval Technology and Social Change. New York: Oxford Univ. Press. ISBN 0195002660. , p.126-127
  2. ^ Milham, Willis I. (1945). Time and Timekeepers. New York: MacMillan. ISBN 0780800087. , p.121
  3. ^ "Clock". The New Encyclopaedia Britannica. 4. Univ. of Chicago. 1974. p. 747. ISBN 0852292902. 
  4. ^ Anzovin, Steve; Podell, Janet (2000). Famous First Facts: A record of first happenings, discoveries, and inventions in world history. H.W. Wilson. ISBN 0824209583. , p.440
  5. ^ Usher, Abbot Payson (1988). A History of Mechanical Inventions. Courier Dover. ISBN 048625593X. , p.305
  6. ^ Dohrn-van Rossum, Gerhard (1997). History of the Hour: Clocks and Modern Temporal Orders. Univ. of Chicago Press. ISBN 0-226-15510-2. , p.121
  7. ^ "Why do mainsprings break?". Technical Note TD105. Hamilton Watch Co.. Retrieved 2007-10-08.  on NAWCC eHorology Virtual Museum
  8. ^ Bretscher, Ulrich (2007). "The Roskopf Watch". Ulrich Bretscher's pocket watch page. Retrieved 2007-12-07. 
  9. ^ De Carle, Donald (1969). Practical Watch Repairing, 3rd Ed.. London: Robert Hale Ltd.. ISBN 0719800307. , p.91
  10. ^ Milham 1945, p.105
  11. ^ De Carle 1969, p.90-91
  12. ^ "Workshop hints: mainsprings". British Horological Institute website. 1997. 

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • mainspring — main spring , n. The principal or most important spring in a piece of mechanism, especially the moving spring of a watch or clock or the spring in a gunlock which impels the hammer. Hence: (Fig.) The chief or most powerful motive; the efficient… …   The Collaborative International Dictionary of English

  • mainspring — index cause (reason), derivation, reason (basis) Burton s Legal Thesaurus. William C. Burton. 2006 …   Law dictionary

  • mainspring — (n.) 1590s, of watches, clocks, etc., from MAIN (Cf. main) (adj.) + SPRING (Cf. spring) (n.3). Figurative use from 1690s …   Etymology dictionary

  • mainspring — ► NOUN 1) the principal spring in a watch, clock, etc. 2) a prime source of motivation or support …   English terms dictionary

  • mainspring — [mān′spriŋ΄] n. 1. the principal spring in a clock, watch, or other mechanism; driving spring, whose steady uncoiling keeps the mechanism running 2. the chief motive or cause …   English World dictionary

  • mainspring — main|spring [ˈmeınsprıŋ] n 1.) the mainspring of sth the most important reason or influence that makes something happen ▪ Christian faith was the mainspring of Peter s life. ▪ Small companies are the mainspring of the British economy. 2.) the… …   Dictionary of contemporary English

  • mainspring — [[t]me͟ɪnsprɪŋ[/t]] mainsprings N COUNT: usu sing, usu the N of n If you say that an idea, emotion, or other factor is the mainspring of something, you mean that it is the most important reason or motive for that thing. [WRITTEN] My life has been …   English dictionary

  • mainspring — noun (C) 1 the mainspring of/for the most important reason or influence that makes something happen: Romantic love had been the mainspring of Augustini s poetry 2 the most important spring in a watch or clock …   Longman dictionary of contemporary English

  • mainspring — UK [ˈmeɪnˌsprɪŋ] / US noun [countable] Word forms mainspring : singular mainspring plural mainsprings formal the most important cause or reason why something happens …   English dictionary

  • mainspring — noun a) The principal spring of a clockwork mechanism, that drives it by uncoiling. He was wise, for he had seen a long succession of mechanical toys arrive to boast and swagger, and by and by break their mainsprings and pass away. b) The most… …   Wiktionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.