Portsmouth Block Mills
The Portsmouth Block Mills form part of the
Portsmouth Dockyardat Portsmouth, Hampshire, England, and were built during the Napoleonic Warsto supply the British Royal Navywith pulleyblocks. They started the age of mass-productionusing all-metal machine tools and are regarded as one of the seminal buildings of the British Industrial Revolution. They are also the site of the first stationary steam engines used by the Admiralty.
English Heritagehas been undertaking a detailed survey of the buildings and the records relating to the machines.
Development of Portsmouth Dockyard
Royal Navyhad evolved by the middle of the eighteenth century into what has been described as the greatest industrial power in the western world. The Admiraltyand Navy Board began a programme of modernisation of dockyards at Portsmouth and Plymouth, and by the start of the war with Revolutionary France possessed the most up-to-date fleet facilities in Europe.
The Dock system at Portsmouth has its origins in the work of
Edmund Dummerin the 1690s. He constructed a series of basins, and wet and dry docks. Alterations were made to these in the course of the eighteenth century. One of the basins had become redundant by 1770, and it was proposed to use this as a sump into which all the water from the other facilities could drain. The water was pumped out by a series of horse-operated chain pumps.
In 1795, Brigadier-General Sir
Samuel Benthamwas appointed by the Admiralty, the first and only Inspector General of Naval Workswith the task of continuing this modernisation, and in particular the introduction of steam power and mechanising the production processes in the dockyard. His office employed several specialists as his assistants - Mechanist ( engineer), Draughtsmen, Architect, Chemist, Clerks, etc. The Inspector General's office was responsible for the introduction at Portsmouth of plant for the rolling of copperplates for sheathing ships, and for forging-mills for the production of metal parts used in the construction of vessels. They also introduced similar modernisation at the other Naval dockyards.
By 1797 work had started on building additional dry docks and on deepening the basins, and Bentham realised that the existing drainage system would not cope with the increased demand. He installed a steam engine designed by a member of his staff,
James Sadler, in 1798 which, as well as working the chain pumps, drove woodworking machinery and a pump to take water from a well round the dockyard for fire-fighting purposes. This well was some convert|400|ft|m|abbr=on away, and the pumps operated by a horizontal reciprocating wooden spear housed in a tunnel running from the engine house to the top of the well. The Sadler engine was a house-built table engineinstalled in a single-storey engine house with integral boiler; it replaced one of the horse-drives to the chain pumps. This engine was replaced in 1807 in the same house by another, more powerful, table engine made by Fenton, Murray and Wood of Leeds, and in turn in 1830 by a Maudslaybeam engine.
In 1800 a
Boulton and Wattbeam engine was ordered as back-up and was housed in a three-storey engine house in line with the Sadler engine house. This engine was replaced in 1837 by another engine made by James Watt and Co.
Space was very tight and expansion of manufacturing facilities was not possible, so by 1802 the drainage basin was filled with two tiers of brick vaults - the lower layer to act as the reservoir, the upper layer as storage, and the roof of the latter being level with the surrounding land, so creating more space. This allowed the construction of two parallel ranges of three-storey wood mills, the southern to incorporate both engine houses and their chimney stacks, the chain pumps and some wood working machinery. The northern range was directly over the vaults and was to house more woodworking machinery. The buildings were designed by
Samuel Bunce, the architect of Bentham's staff.
While the vaults were under construction Bentham was ordering woodworking machinery of his own design, mostly up-and-down saws and circular saws. These were fitted-up in both ranges, the power to drive them being transmitted from the engines to the north range by underdrives through the upper layer of vaults, and then by vertical shafts to the upper floors of the buildings. The final drives to the machines was by flat belts running on pulleys.
This machinery was planned to cut timber for the numerous smaller parts used in shipbuilding, especially joinery, which had previously been cut by hand, such as components for tables and benches, as well as small turned goods like belaying pins. There is evidence that he had developed a rotary wood-planing machine, but details of this are obscure. There is also evidence that the complex housed a pipe boring machine, whereby straight elm trees were bored out for pump dales. These could be up to 40 ft long and were fitted through the decks of a vessel to pump seawater to the deck. There was a machine for making treenails - long wooden dowels used for fixing wooden parts of a ship together.
The Royal Navy used large numbers of blocks, which were all hand-made by contractors. Their quality was not consistent, the supply problematic and they were expensive. A typical ship of the line needed about 1000 blocks of different sizes, and in the course of the year the Navy required over 100,000. Bentham had devised some machines for making blocks, but did not develop them and details of how they worked are now obscure. In 1802
Marc Isambard Brunelproposed to the Admiralty a system of making blocks using machinery he had patented. Bentham appreciated the superiority of Brunel's system and in August 1802 he was authorised by the Admiralty to proceed.
There were three series of block-making machines, each designed to make a range of block sizes. They were laid out to allow a production line, so each stage of the work progressed to the next in a natural flow. The yard between the two wood mill buildings was walled-off and roofed to form a new workshop to house the block-making machines.
The first set, for medium blocks, was installed in January 1803, the second set for smaller blocks in May 1803, and the third set for large blocks in March 1805. There were numerous changes of layout and some modification of the plant until in September 1807 the plant was felt able to fulfil all the needs of the Navy: In 1808 130,000 blocks were produced.
The block-making processes using the machines
A pulley-block has four parts: the shell, the sheave, the pin for locating the latter in the shell and a metal bush, or coak, inserted into the sheave to save wear between it and the pin. Blocks can vary in size and in the number of sheaves.
The process of making the shells
* Cut slices from the trunk of a tree, and from these slices by means of the
circular saws cut rectangular blocks from which the shells were manufactured.
* Bore a hole in the block for the pin, and at right angles to this a hole or holes to receive the morticing chisels,(depending on the number of mortices). The clamp used to hold the block at the same time indented locating points by which the blocks were secured in the later machines, thus ensuring consistent location and measurement in the subsequent processes.
* Mortice the blocks by a self-acting machine. The morticing chisel reciprocated vertically, and at the same time the vice gripping the block was gradually moved each cut. Once the length of the mortice had been cut the machine automatically stopped to allow the block to be replaced with a new one.
* Cut the corners off the block by a circular saw with angled guides.
* Shape the 4 faces of the blocks to a shallow curve. This was done by a machine where a number of blocks were clamped in the periphery of a revolving wheel. The cutter was swept in a curve across the faces of the blocks as they rotated. The radius of the curve was controlled by a former. After each cut the blocks were turned 90 degrees to bring up a new face.
* Each block was then placed in a machine which scored a shallow groove, by means of a revolving cutter, to give a location for the securing ropes.
The process of making the sheaves
* Cut a slice across a trunk of
Lignum Vitae. The machine for this allowed the log to be rotated at the same time as the circular saw operated, ensuring that an equal thickness was maintained. The position of the log for each new cut was controlled by a leadscrew ensuring great accuracy.
* Make a circular disc from this slice by means of a rounding saw, which simultaneously bored out the middle and shaped the outer edge.
* Mill out from each face a profile to take the outer face of the coak
* The coak was inserted into the sheave, and a retaining ring
rivetted to keep it in place.
* Broach out the hole in the coak to the size of the requisite pin.
* The finished sheave was faced-off on both sides in a special lathe, and the rope groove was machined on the edge.
The process of making the pins
* The pin blanks were forged slightly oversize with a square left on one end.
* They were turned to size on the circular part in a special
* They were given a burnished finish between hardened dies
* One source says they were then tinned to preserve them from rust.
The process of making the metal coaks
* These were cast in bell-metal and the mould left grease-retaining grooves in the inner bore. One end of the coak had a flange and a loose ring was supplied for the other end, together these parts gave a seating for the rivets which fixed the coak to the sheave.
* The shells were smoothed by hand with a spoke shave and then the sheave and pin assembled. They were stored in the Block Mills and issued as demanded.
These machines utilised several features for the first time which have since become commonplace in machine design.
* The boring operation indented gauging points in the wooden blocks which the clamps of the later machines used to locate the blocks precisely. This meant that positioning of the block in later processes ensured accurate location in relation to the tool working on it.
* Several of the machines had cone clutches.
* Brunel used detachable tool bits held in tool holders very similar to those use now on general purpose lathes.
* Expanding collet chucks were used to locate the sheaves by gripping the internal bore, during certain operations.
* Two-jaw gripping chucks were used on some machines. These were precursors of the three-jaw chucks used on lathes today.
* The morticing machines could be set to stop automatically once the operation was finished.
Interchangeabilityof the sheaves and pins was possible, since they were not married to a particular shell.
* The work-flow is perhaps best described as
batch production, because of the range of block sizes demanded. But it was basically a production-linesystem, nevertheless. This method of working did not catch on in general manufacturing in Britain for many decades, and when it did it was imported from America.
*The entire system was designed to be worked by labourers and not apprentice-trained craftsmen. Each man was trained to operate two or more machines and could be moved round the plant as required.
The Manufacture of the Block-making machines
Brunel's patent specification shows wooden framed machines, which, while they show many of the principles of the machines actually installed bear little resemblance to the final designs. Once the contract with the Admiralty had been placed he engaged
Henry Maudslayto make them, and it is clear the final designs had considerable input from Bentham, Maudslay, Simon Goodrich, (mechanician to the Navy board) as well as Brunel himself.
These machines were almost entirely hand made, the only machine tools used being lathes to machine circular parts, and drilling machines for boring small holes. At that time there were no milling, planing or shaping machines, and all flat surfaces were made by hand chipping, filing and scraping. There is evidence that the grinding of flats was also done to get near-precision finishes. Each nut was made to fit its matching bolt and were numbered to ensure they were replaced correctly. This was before the days of
interchangeability, of course. The materials used were cast and wrought iron, brass and gun metal. The use of metal throughout their construction greatly improved their rigidity and accuracy which became the standard for later machine tool manufacture.
These machines and the block mills attracted an enormous amount of interest from the time of their erection, ranging from Admiral
Lord Nelsonon the morning of the day he embarked from Portsmouth for the Battle of Trafalgar on 1805, to the Princess Victoria at the age of 12, as part of her education. Even during the time of the Napoleonic Wars, until 1815 there was a stream of foreign dignitaries and military men wishing to learn. The machines were fully described and illustrated in the Edinburgh Encyclopaedia, (1811), Rees's Cyclopaedia, (1812), the supplement to the 4th edition of Encyclopædia Britannica(1817) and the Encyclopaedia Metropolitana. Later encyclopaedias such as Tomlinson's Encyclopaediaand the Penny Cyclopaediaderived their accounts from these earlier publications.
These accounts concentrated almost entirely on the blockmaking machinery, and ignored the saw-milling side of the mills, and in consequence modern commentators have not discussed this aspect of the Block Mills. The sawmills were important since Brunel was enabled to develop his ideas which he employed later in his private veneer mill at Battersea, and the
Royal Navysaw mills at Woolwich Dockyardand Chatham Dockyard, as well as mills he designed for private concerns, such as Borthwick's at Leithin Scotland.
The Block Mills have remained in constant Navy occupation ever since and in consequence are not open to the public. Manufacture of blocks using these machines naturally declined over the years, production finally stopping in the 1960s, but some of the original machines, part of the transmission drives and the engine-house shells still survive in the buildings. The
National Museum of Science and Industry, London, has a selection of machines, donated by the Admiralty between 1933 and 1951, and others are on display in the Dockyard Apprentice Museumat Portsmouth. Several websites claim that the Smithsonian Institutionin Washington, D.C.also has machines from Portsmouth: this is a myth, according to the Institution.
The Block Mills have not been in use for many years, although a lot of the original pulley systems remain in situ, albeit in a poor state of repair. The building is also in a poor state of repair and is a high priority for both
English Heritageand the Ministry of Defence. As of 2006 a project is underway to ensure the building and contents are preserved, if not restored.
* [http://www.makingthemodernworld.org.uk/stories/enlightenment_and_measurement/05.ST.02/?scene=3&tv=true National Museum of Science and Industry, London - Making of the Modern World]
* [http://www.ingenious.org.uk Engravings from the Rees's Cyclopaedia account of the block mills]
* The English Heritage reports and other documentation may be consulted as they become available in the National Monuments Record at Swindon, Wiltshire. [http://accessibility.english-heritage.org.uk/Default.asp?WCI=Node&WCE=146]
* Gilbert, K. R. "The Portsmouth Block-making Machinery", London, 1965
* Cooper, C. C. 'The Production Line at Portsmouth Block Mill', in "Industrial Archaeology Review" VI, 1982, 28-44
* Cooper, C. C. 'The Portsmouth System of Manufacture', "Technology and Culture", 25, 1984, 182-225
* Coad, Jonathan, "The Royal Dockyards 1690-1850", Aldershot, 1989
* Coad, Jonathan, "The Portsmouth Block Mills : Bentham, Brunel and the start of the Royal Navy's Industrial Revolution", 2005,ISBN 1-873592-87-6
* Wilkin, Susan, "The application of emerging new technologies by Portsmouth Dockyard, 1790-1815", The Open University PhD Thesis, 1999. (Copies available from the British Thesis service of the British Library)
* Cantrell, J. and Cookson, G. eds. "Henry Maudslay and the Pioneers of the Machine Age", Stroud, 2002
Wikimedia Foundation. 2010.
Look at other dictionaries:
Portsmouth Block Mills — Intérieur du Portsmouth Block Mills. Le Portsmouth Block Mills est une fabrique de poulies faisant partie des Portsmouth Dockyard à Portsmouth, Hampshire, Angleterre, et son construit pendant les guerres napoléoniennes afin de fournir la Royal… … Wikipédia en Français
Portsmouth — For other places with the same name, see Portsmouth (disambiguation). Portsmouth City and Unitary Authority Area City of Portsmouth … Wikipedia
Block (sailing) — In sailing, a block is a single or multiple pulley. One or a number of sheaves are enclosed in an assembly between cheeks or chocks . In use a block is fixed to the end of a line, to a spar or to a surface. Rope or line is rove through the… … Wikipedia
HMNB Portsmouth — Her Majesty s Naval Base (HMNB) Portsmouth (HMS Nelson ), is one of three operating bases for the Royal Navy (the others being HMNB Clyde and HMNB Devonport). Portsmouth naval base is located on the eastern shore of Portsmouth Harbour and is part … Wikipedia
John Jervis — 1er comte de St Vincent Portrait de John Jervis en jeune capitaine par Francis Cotes … Wikipédia en Français
Marc Isambard Brunel — Sir Marc Isambard Brunel, by James Northcote Born Marc Isambard Brunel April 25, 1769(1769 04 25) … Wikipedia
Marc Isambart Brunel — Naissance 1769 Hacqueville Décès 1849 (à 80 ans) Londres … Wikipédia en Français
Marc Isambert Brunel — Marc Isambart Brunel Marc Isambart Brunel Naissance 1769 Hacqueville Décès 1849 (à 80 ans) Londres … Wikipédia en Français
Simon Goodrich — (1773 1847) was an engineer to the British Navy Board.He was born 28 October 1773 in Suffolk. In 1796 was appointed draughtsman in the office of Sir Samuel Bentham, Inspector General of Naval Works, and in 1799 was promoted to the post of… … Wikipedia
Henry Maudslay — Not to be confused with Henry Maudsley. Maudslay redirects here. For other uses, see Maudslay (disambiguation). Henry Maudslay Portrait by Pierre Louis ( Henri ) Grevedon 1827 Born 22 … Wikipedia