 Network analysis (electrical circuits)

Linear Network Analysis Elements Components Series and parallel circuits Impedance transforms Generator theorems Network theorems Network analysis methods Twoport parameters A network, in the context of electronics, is a collection of interconnected components. Network analysis is the process of finding the voltages across, and the currents through, every component in the network. There are a number of different techniques for achieving this. However, for the most part, they assume that the components of the network are all linear. The methods described in this article are only applicable to linear network analysis except where explicitly stated.
Definitions
Component A device with two or more terminals into which, or out of which, charge may flow. Node A point at which terminals of more than two components are joined. A conductor with a substantially zero resistance is considered to be a node for the purpose of analysis. Branch The component(s) joining two nodes. Mesh A group of branches within a network joined so as to form a complete loop. Port Two terminals where the current into one is identical to the current out of the other. Circuit A current from one terminal of a generator, through load component(s) and back into the other terminal. A circuit is, in this sense, a oneport network and is a trivial case to analyse. If there is any connection to any other circuits then a nontrivial network has been formed and at least two ports must exist. Often, "circuit" and "network" are used interchangeably, but many analysts reserve "network" to mean an idealised model consisting of ideal components.^{[1]} Transfer function The relationship of the currents and/or voltages between two ports. Most often, an input port and an output port are discussed and the transfer function is described as gain or attenuation. Component transfer function For a twoterminal component (i.e. oneport component), the current and voltage are taken as the input and output and the transfer function will have units of impedance or admittance (it is usually a matter of arbitrary convenience whether voltage or current is considered the input). A three (or more) terminal component effectively has two (or more) ports and the transfer function cannot be expressed as a single impedance. The usual approach is to express the transfer function as a matrix of parameters. These parameters can be impedances, but there is a large number of other approaches, see twoport network. Equivalent circuits
Main article: equivalent impedance transformsA useful procedure in network analysis is to simplify the network by reducing the number of components. This can be done by replacing the actual components with other notional components that have the same effect. A particular technique might directly reduce the number of components, for instance by combining impedances in series. On the other hand it might merely change the form in to one in which the components can be reduced in a later operation. For instance, one might transform a voltage generator into a current generator using Norton's theorem in order to be able to later combine the internal resistance of the generator with a parallel impedance load.
A resistive circuit is a circuit containing only resistors, ideal current sources, and ideal voltage sources. If the sources are constant (DC) sources, the result is a DC circuit. The analysis of a circuit refers to the process of solving for the voltages and currents present in the circuit. The solution principles outlined here also apply to phasor analysis of AC circuits.
Two circuits are said to be equivalent with respect to a pair of terminals if the voltage across the terminals and current through the terminals for one network have the same relationship as the voltage and current at the terminals of the other network.
If V_{2} = V_{1} implies I_{2} = I_{1} for all (real) values of V_{1}, then with respect to terminals ab and xy, circuit 1 and circuit 2 are equivalent.
The above is a sufficient definition for a oneport network. For more than one port, then it must be defined that the currents and voltages between all pairs of corresponding ports must bear the same relationship. For instance, star and delta networks are effectively three port networks and hence require three simultaneous equations to fully specify their equivalence.
Impedances in series and in parallel
Any two terminal network of impedances can eventually be reduced to a single impedance by successive applications of impendances in series or impendances in parallel.
Impedances in series:
Impedances in parallel:
 The above simplified for only two impedances in parallel:
Deltawye transformation
Main article: YΔ transformA network of impedances with more than two terminals cannot be reduced to a single impedance equivalent circuit. An nterminal network can, at best, be reduced to n impedances (at worst ^{n}C_{2}). For a three terminal network, the three impedances can be expressed as a three node delta (Δ) network or a four node star (Y) network. These two networks are equivalent and the transformations between them are given below. A general network with an arbitrary number of nodes cannot be reduced to the minimum number of impedances using only series and parallel combinations. In general, YΔ and ΔY transformations must also be used. For some networks the extension of YΔ to starpolygon transformations may also be required.
For equivalence, the impedances between any pair of terminals must be the same for both networks, resulting in a set of three simultaneous equations. The equations below are expressed as resistances but apply equally to the general case with impedances.
Deltatostar transformation equations
Startodelta transformation equations
General form of network node elimination
The startodelta and seriesresistor transformations are special cases of the general resistor network node elimination algorithm. Any node connected by N resistors (R_{1} .. R_{N}) to nodes 1 .. N can be replaced by resistors interconnecting the remaining N nodes. The resistance between any two nodes x and y is given by:
For a startodelta (N = 3) this reduces to:
For a series reduction (N = 2) this reduces to:
For a dangling resistor (N = 1) it results in the elimination of the resistor because .
Source transformation
A generator with an internal impedance (i.e. nonideal generator) can be represented as either an ideal voltage generator or an ideal current generator plus the impedance. These two forms are equivalent and the transformations are given below. If the two networks are equivalent with respect to terminals ab, then V and I must be identical for both networks. Thus,
 or
 Norton's theorem states that any twoterminal network can be reduced to an ideal current generator and a parallel impedance.
 Thévenin's theorem states that any twoterminal network can be reduced to an ideal voltage generator plus a series impedance.
Simple networks
Some very simple networks can be analysed without the need to apply the more systematic approaches.
Voltage division of series components
Main article: voltage divisionConsider n impedances that are connected in series. The voltage V_{i} across any impedance Z_{i} is
Current division of parallel components
Main article: current divisionConsider n impedances that are connected in parallel. The current I_{i} through any impedance Z_{i} is
for i = 1,2,...,n.
Special case: Current division of two parallel components
Nodal analysis
Main article: nodal analysis1. Label all nodes in the circuit. Arbitrarily select any node as reference.
2. Define a voltage variable from every remaining node to the reference. These voltage variables must be defined as voltage rises with respect to the reference node.
3. Write a KCL equation for every node except the reference.
4. Solve the resulting system of equations.
Mesh analysis
Main article: mesh analysisMesh — a loop that does not contain an inner loop.
1. Count the number of “window panes” in the circuit. Assign a mesh current to each window pane.
2. Write a KVL equation for every mesh whose current is unknown.
3. Solve the resulting equations
Superposition
Main article: Superposition theoremIn this method, the effect of each generator in turn is calculated. All the generators other than the one being considered are removed; either shortcircuited in the case of voltage generators, or open circuited in the case of current generators. The total current through, or the total voltage across, a particular branch is then calculated by summing all the individual currents or voltages.
There is an underlying assumption to this method that the total current or voltage is a linear superposition of its parts. The method cannot, therefore, be used if nonlinear components are present. Note that mesh analysis and node analysis also implicitly use superposition so these too, are only applicable to linear circuits.
Choice of method
Choice of method^{[2]} is to some extent a matter of taste. If the network is particularly simple or only a specific current or voltage is required then adhoc application of some simple equivalent circuits may yield the answer without recourse to the more systematic methods.
 Superposition is possibly the most conceptually simple method but rapidly leads to a large number of equations and messy impedance combinations as the network becomes larger.
 Nodal analysis: The number of voltage variables, and hence simultaneous equations to solve, equals the number of nodes minus one. Every voltage source connected to the reference node reduces the number of unknowns (and equations) by one. Nodal analysis is thus best for voltage sources.
 Mesh analysis: The number of current variables, and hence simultaneous equations to solve, equals the number of meshes. Every current source in a mesh reduces the number of unknowns by one. Mesh analysis is thus best for current sources. Mesh analysis, however, can only be used with networks which can be drawn as a planar network, that is, with no crossing components.^{[3]}
Transfer function
A transfer function expresses the relationship between an input and an output of a network. For resistive networks, this will always be a simple real number or an expression which boils down to a real number. Resistive networks are represented by a system of simultaneous algebraic equations. However in the general case of linear networks, the network is represented by a system of simultaneous linear differential equations. In network analysis, rather than use the differential equations directly, it is usual practice to carry out a Laplace transform on them first and then express the result in terms of the Laplace parameter s, which in general is complex. This is described as working in the sdomain. Working with the equations directly would be described as working in the time (or t) domain because the results would be expressed as time varying quantities. The Laplace transform is the mathematical method of transforming between the sdomain and the tdomain.
This approach is standard in control theory and is useful for determining stability of a system, for instance, in an amplifier with feedback.
Two terminal component transfer functions
For two terminal components the transfer function, otherwise called the constitutive equation, is the relationship between the current input to the device and the resulting voltage across it. The transfer function, Z(s), will thus have units of impedance  ohms. For the three passive components found in electrical networks, the transfer functions are;
Resistor Inductor Capacitor For a network to which only steady ac signals are applied, s is replaced with jω and the more familiar values from ac network theory result.
Resistor Inductor Capacitor Finally, for a network to which only steady dc is applied, s is replaced with zero and dc network theory applies.
Resistor Inductor Capacitor Two port network transfer function
Transfer functions, in general, in control theory are given the symbol H(s). Most commonly in electronics, transfer function is defined as the ratio of output voltage to input voltage and given the symbol A(s), or more commonly (because analysis is invariably done in terms of sine wave response), A(jω), so that;
The A standing for attenuation, or amplification, depending on context. In general, this will be a complex function of jω, which can be derived from an analysis of the impedances in the network and their individual transfer functions. Sometimes the analyst is only interested in the magnitude of the gain and not the phase angle. In this case the complex numbers can be eliminated from the transfer function and it might then be written as;
Two port parameters
Main article: Twoport networkThe concept of a twoport network can be useful in network analysis as a black box approach to analysis. The behaviour of the twoport network in a larger network can be entirely characterised without necessarily stating anything about the internal structure. However, to do this it is necessary to have more information than just the A(jω) described above. It can be shown that four such parameters are required to fully characterise the twoport network. These could be the forward transfer function, the input impedance, the reverse transfer function (i.e., the voltage appearing at the input when a voltage is applied to the output) and the output impedance. There are many others (see the main article for a full listing), one of these expresses all four parameters as impedances. It is usual to express the four parameters as a matrix;
The matrix may be abbreviated to a representative element;
or just
These concepts are capable of being extended to networks of more than two ports. However, this is rarely done in reality as in many practical cases ports are considered either purely input or purely output. If reverse direction transfer functions are ignored, a multiport network can always be decomposed into a number of twoport networks.
Distributed components
Where a network is composed of discrete components, analysis using twoport networks is a matter of choice, not essential. The network can always alternatively be analysed in terms of its individual component transfer functions. However, if a network contains distributed components, such as in the case of a transmission line, then it is not possible to analyse in terms of individual components since they do not exist. The most common approach to this is to model the line as a twoport network and characterise it using twoport parameters (or something equivalent to them). Another example of this technique is modelling the carriers crossing the base region in a high frequency transistor. The base region has to be modelled as distributed resistance and capacitance rather than lumped components.
Image analysis
Main article: Image impedanceTransmission lines and certain types of filter design use the image method to determine their transfer parameters. In this method, the behaviour of an infinitely long cascade connected chain of identical networks is considered. The input and output impedances and the forward and reverse transmission functions are then calculated for this infinitely long chain. Although the theoretical values so obtained can never be exactly realised in practice, in many cases they serve as a very good approximation for the behaviour of a finite chain as long as it is not too short.
Nonlinear networks
Most electronic designs are, in reality, nonlinear. There is very little that does not include some semiconductor devices. These are invariably nonlinear, the transfer function of an ideal semiconductor pn junction is given by the very nonlinear relationship;
where;
 i and v are the instantaneous current and voltage.
 I_{o} is an arbitrary parameter called the reverse leakage current whose value depends on the construction of the device.
 V_{T} is a parameter proportional to temperature called the thermal voltage and equal to about 25mV at room temperature.
There are many other ways that nonlinearity can appear in a network. All methods utilising linear superposition will fail when nonlinear components are present. There are several options for dealing with nonlinearity depending on the type of circuit and the information the analyst wishes to obtain.
Constitutive equations
The diode equation above is an example of a constitutive equation of the general form,
This can be thought of as a nonlinear resistor. The corresponding constitutive equations for nonlinear inductors and capacitors are respectively;
where f is any arbitrary function, φ is the stored magnetic flux and q is the stored charge.
Existence, uniqueness and stability
An important consideration in nonlinear analysis is the question of uniqueness. For a network composed of linear components there will always be one, and only one, unique solution for a given set of boundary conditions. This is not always the case in nonlinear circuits. For instance, a linear resistor with a fixed voltage applied to it has only one solution for the current through it. On the other hand, the nonlinear tunnel diode has up to three solutions for the current for a given voltage. That is, a particular solution for the current through the diode is not unique, there may be others, equally valid. In some cases there may not be a solution at all: the question of existence of solutions must be considered.
Another important consideration is the question of stability. A particular solution may exist, but it may not be stable, rapidly departing from that point at the slightest stimulation. It can be shown that a network that is absolutely stable for all conditions must have one, and only one, solution for each set of conditions.^{[4]}
Methods
Boolean analysis of switching networks
A switching device is one where the nonlinearity is utilised to produce two opposite states. CMOS devices in digital circuits, for instance, have their output connected to either the positive or the negative supply rail and are never found at anything in between except during a transient period when the device is actually switching. Here the nonlinearity is designed to be extreme, and the analyst can actually take advantage of that fact. These kinds of networks can be analysed using Boolean algebra by assigning the two states ("on"/"off", "positive"/"negative" or whatever states are being used) to the boolean constants "0" and "1".
The transients are ignored in this analysis, along with any slight discrepancy between the actual state of the device and the nominal state assigned to a boolean value. For instance, boolean "1" may be assigned to the state of +5V. The output of the device may actually be +4.5V but the analyst still considers this to be boolean "1". Device manufacturers will usually specify a range of values in their data sheets that are to be considered undefined (i.e. the result will be unpredictable).
The transients are not entirely uninteresting to the analyst. The maximum rate of switching is determined by the speed of transition from one state to the other. Happily for the analyst, for many devices most of the transition occurs in the linear portion of the devices transfer function and linear analysis can be applied to obtain at least an approximate answer.
It is mathematically possible to derive boolean algebras which have more than two states. There is not too much use found for these in electronics, although threestate devices are passingly common.
Separation of bias and signal analyses
This technique is used where the operation of the circuit is to be essentially linear, but the devices used to implement it are nonlinear. A transistor amplifier is an example of this kind of network. The essence of this technique is to separate the analysis in to two parts. Firstly, the dc biases are analysed using some nonlinear method. This establishes the quiescent operating point of the circuit. Secondly, the small signal characteristics of the circuit are analysed using linear network analysis. Examples of methods that can be used for both these stages are given below.
Graphical method of dc analysis
In a great many circuit designs, the dc bias is fed to a nonlinear component via a resistor (or possibly a network of resistors). Since resistors are linear components, it is particularly easy to determine the quiescent operating point of the nonlinear device from a graph of its transfer function. The method is as follows: from linear network analysis the output transfer function (that is output voltage against output current) is calculated for the network of resistor(s) and the generator driving them. This will be a straight line and can readily be superimposed on the transfer function plot of the nonlinear device. The point where the lines cross is the quiescent operating point.
Perhaps the easiest practical method is to calculate the (linear) network open circuit voltage and short circuit current and plot these on the transfer function of the nonlinear device. The straight line joining these two point is the transfer function of the network.
In reality, the designer of the circuit would proceed in the reverse direction to that described. Starting from a plot provided in the manufacturers data sheet for the nonlinear device, the designer would choose the desired operating point and then calculate the linear component values required to achieve it.
It is still possible to use this method if the device being biased has its bias fed through another device which is itself nonlinear  a diode for instance. In this case however, the plot of the network transfer function onto the device being biased would no longer be a straight line and is consequently more tedious to do.
Small signal equivalent circuit
This method can be used where the deviation of the input and output signals in a network stay within a substantially linear portion of the nonlinear devices transfer function, or else are so small that the curve of the transfer function can be considered linear. Under a set of these specific conditions, the nonlinear device can be represented by an equivalent linear network. It must be remembered that this equivalent circuit is entirely notional and only valid for the small signal deviations. It is entirely inapplicable to the dc biasing of the device.
For a simple twoterminal device, the small signal equivalent circuit may be no more than two components. A resistance equal to the slope of the v/i curve at the operating point (called the dynamic resistance), and tangent to the curve. A generator, because this tangent will not, in general, pass through the origin. With more terminals, more complicated equivalent circuits are required.
A popular form of specifying the small signal equivalent circuit amongst transistor manufacturers is to use the twoport network parameters known as [h] parameters. These are a matrix of four parameters as with the [z] parameters but in the case of the [h] parameters they are a hybrid mixture of impedances, admittances, current gains and voltage gains. In this model the three terminal transistor is considered to be a two port network, one of its terminals being common to both ports. The [h] parameters are quite different depending on which terminal is chosen as the common one. The most important parameter for transistors is usually the forward current gain, h_{21}, in the common emitter configuration. This is designated h_{fe} on data sheets.
The small signal equivalent circuit in terms of twoport parameters leads to the concept of dependent generators. That is, the value of a voltage or current generator depends linearly on a voltage or current elsewhere in the circuit. For instance the [z] parameter model leads to dependent voltage generators as shown in this diagram;
There will always be dependent generators in a twoport parameter equivalent circuit. This applies to the [h] parameters as well as to the [z] and any other kind. These dependencies must be preserved when developing the equations in a larger linear network analysis.
Piecewise linear method
In this method, the transfer function of the nonlinear device is broken up into regions. Each of these regions is approximated by a straight line. Thus, the transfer function will be linear up to a particular point where there will be a discontinuity. Past this point the transfer function will again be linear but with a different slope.
A well known application of this method is the approximation of the transfer function of a pn junction diode. The actual transfer function of an ideal diode has been given at the top of this (nonlinear) section. However, this formula is rarely used in network analysis, a piecewise approximation being used instead. It can be seen that the diode current rapidly diminishes to I_{o} as the voltage falls. This current, for most purposes, is so small it can be ignored. With increasing voltage, the current increases exponentially. The diode is modelled as an open circuit up to the knee of the exponential curve, then past this point as a resistor equal to the bulk resistance of the semiconducting material.
The commonly accepted values for the transition point voltage are 0.7V for silicon devices and 0.3V for germanium devices. An even simpler model of the diode, sometimes used in switching applications, is short circuit for forward voltages and open circuit for reverse voltages.
The model of a forward biased pn junction having an approximately constant 0.7V is also a much used approximation for transistor baseemitter junction voltage in amplifier design.
The piecewise method is similar to the small signal method in that linear network analysis techniques can only be applied if the signal stays within certain bounds. If the signal crosses a discontinuity point then the model is no longer valid for linear analysis purposes. The model does have the advantage over small signal however, in that it is equally applicable to signal and dc bias. These can therefore both be analysed in the same operations and will be linearly superimposable.
Timevarying components
In linear analysis, the components of the network are assumed to be unchanging, but in some circuits this does not apply, such as sweep oscillators, voltage controlled amplifiers, and variable equalisers. In many circumstances the change in component value is periodic. A nonlinear component excited with a periodic signal, for instance, can be represented as periodically varying linear component. Sidney Darlington disclosed a method of analysing such periodic time varying circuits. He developed canonical circuit forms which are analogous to the canonical forms of Ronald Foster and Wilhelm Cauer used for analysing linear circuits.^{[5]}
See also
 Bartlett's bisection theorem
 Circuit theory
 Equivalent impedance transforms
 Kirchhoff's circuit laws
 Mesh analysis
 Millman's Theorem
 Ohm's law
 Reciprocity theorem
 Resistive circuit
 Series and parallel circuits
 Tellegen's theorem
 Twoport network
 Wyedelta transform
 Symbolic circuit analysis
References
 ^ Belevitch V (May 1962). "Summary of the history of circuit theory". Proceedings of the IRE 50 (5): 849. doi:10.1109/JRPROC.1962.288301. cites "IRE Standards on Circuits: Definitions of Terms for Linear Passive Reciprocal Time Invariant Networks, 1960". Proceedings of the IRE 48 (9): 1609. September 1960. doi:10.1109/JRPROC.1960.287676.to justify this definition.
Sidney Darlington Darlington S (1984). "A history of network synthesis and filter theory for circuits composed of resistors, inductors, and capacitors". IEEE Trans. Circuits and Systems 31 (1): 4.
follows Belevitch but notes there are now also many colloquial uses of "network".  ^ Nilsson, J W, Riedel, S A (2007). Electric Circuits (8th ed.). Pearson Prentice Hall. pp. 112–113. ISBN 0131989251. http://books.google.com/books?id=sxmM8RFL99wC&lpg=PA200&dq=isbn%3A0131989251&pg=PA112#v=onepage&q=112&f=false.
 ^ Nilsson, J W, Riedel, S A (2007). Electric Circuits (8th ed.). Pearson Prentice Hall. p. 94. ISBN 0131989251. http://books.google.com/books?id=sxmM8RFL99wC&lpg=PA200&dq=isbn%3A0131989251&pg=PA94#v=onepage&q=&f=false.
 ^ Ljiljana Trajković, "Nonlinear circuits", The Electrical Engineering Handbook (Ed: WaiKai Chen), pp.7981, Academic Press, 2005 ISBN 0121709604
 ^ US patent 3265973, Sidney Darlington, Irwin W. Sandberg, "Synthesis of twoport networks having periodically timevarying elements", issued 19660809
External links
 Circuit Analysis Techniques — includes node/mesh analysis, superposition, and thevenin/norton transformation
 Nodal Analysis of Op Amp Circuits
 Analysis of Resistive Circuits
 Circuit Analysis Related Laws, Examples and Solutions
 Solved problems in electrical circuits
Categories: Electronic design
Wikimedia Foundation. 2010.
Look at other dictionaries:
Network analyzer (electrical) — Not to be confused with packet analyzer or telecom network protocol analyzer. ZVA40 vector network analyser from Rohde Schwarz. A network analyzer is an instrument that measures the network parameters of electrical networks. Today, network… … Wikipedia
Electrical network — For electrical power transmission grids and distribution networks, see Grid (electricity). A simple electric circuit made up of a voltage source and a resistor. Here, V = iR, according to Ohm s Law. An electrical network is an interconnection of… … Wikipedia
Electrical element — Electrical elements are conceptual abstractions representing idealized electrical components, such as resistors, capacitors, and inductors, used in the analysis of electrical networks. Any electrical network can be analysed as multiple,… … Wikipedia
Electrical engineering — Electrical engineering, sometimes referred to as electrical and electronic engineering, is a field of engineering that deals with the study and application of electricity, electronics and electromagnetism. The field first became an identifiable… … Wikipedia
Network synthesis filters — Network synthesis is a method of designing signal processing filters. It has produced several important classes of filter including the Butterworth filter, the Chebyshev filter and the Elliptic filter. It was originally intended to be applied to… … Wikipedia
Electrical impedance — Electromagnetism Electricity · … Wikipedia
Electrical telegraph — A printing electrical telegraph receiver, and a transmitter key at bottom right An electrical telegraph is a telegraph that uses electrical signals, usually conveyed via telecommunication lines or radio. The electromagnetic telegraph is a device… … Wikipedia
Network protector — A network protector (also reverse power relay) is a type of electric protective device used in electricity distribution systems. The function of the network protector is to automatically connect and disconnect its associated power transformer… … Wikipedia
Power network design (IC) — In integrated circuits, electrical power is distributed to the components of the chip over a network of conductors on the chip. Power network design (IC) includes the analysis and design of such networks. As in all engineering, this involves… … Wikipedia
Zobel network — Linear analog electronic filters Network synthesis filters Butterworth filter Chebyshev filter Elliptic (Cauer) filter Bessel filter Gaussian filter Optimum L (Legendre) filter Linkwitz Riley filter … Wikipedia