Rising damp (structural)

Rising damp is a condition caused by ground moisture rising up a masonry wall by capillary action. It occurs where there is no damp-proof course (DPC) or where the DPC has been damaged or bridged. Where present, moisture can rise up the wall to a height of a metre and it will often leave a characteristic horizontal 'tide mark'.

ymptoms

Rising damp tends to cause secondary damage to a building. The unwanted moisture enables the growth of various fungi in wood, causing rot. Plaster and paint deteriorate and wallpaper loosens. Stains, from the water, salts and from mold, mar surfaces. Externally, mortar may crumble and salt stains may appear on the walls. Steel & iron fasteners rust. It may also cause respiratory illness in occupants. In extreme cases, mortar or plaster may fall away from the affected wall.

Prevention

Well built modern houses include a synthetic damp-proof course (DPC), about 15cm above ground level, to act as a barrier through which water cannot pass. Therefore the problem is mainly related to older structures, where no water proof barrier was utilised, or where ill designed building modifications have been performed. However, slate or "engineering bricks" with a low porosity were often used for the first few courses above ground level, and these can minimise the problem.

Treatment

Effective treatment is a specialized job and is expensive and labour intensive. The cause of the damp must first be eliminated, by installing a physical or chemical DPC. Then, any affected plaster or mortar must be removed, and the wall treated with a solution of acetic acid, before replacing the plaster and repainting. The major Rising damp treatment authorities within the U.K. are The British Wood Preserving and Damp-proofing Association (BWPDA) and The Property Care Association.

imilar defects

Before any remedial work is started, it is important to determine that the symptoms seen in the structure are in fact rising damp and not penetrating damp or condensation. It is common for any or all of these defects to be present present simulataneously.

Identification of rising damp

Inexpensive instruments are available which measure the extent and amount of moisture in building materials. They consist of a conductivity meter and a couple of spikes that are pressed into the material to be tested. In general, they can only be used inside the building. They give an excellent indication of the extent of the problem even when there is not yet any visible damage, but no clue as to the cause. Hence further clues must be sought.

Further clues

Once the extent of the problem has been determined by the instrument, further investgations have to be made,
Is there a damp course present and what is it's nature? The damp proof course, if there is one, should be clearly visble on the outside wall and it should be at least 150mm above the ground level and immediately below any floor joists. It's edges should be visible, ie not covered by cement. If there is a damp proof course and it is a plastic or bitumous type barrier them the chances of it's failure are slight although "bridging" sometimes occurs due to the application of cement renderingIf it consists of slate or engineering bricks, then failure is possible. Slate damp proof courses often have the appearance of the thick horizontal cement joint. A double layer of slates is common with the joints staggered. Failure occurs when the slates break through building movement or bridging takes place.Engineering bricks (two or three courses)often have a different appearance to the other brickwork. Failure can be due to wide and/or porous vertices, or the bricks being of inferior qualityEven when there is no damp proof course there may be no significant rising damp (depending on the difference between internal and external floor levels, and also ground conditions.)
Condensation comes from human activities in the building, cooking bathing etc. The moisture in the air condenses on cold surfaces. Buildings with poorly insulated walls are very prone to this problem. It often causes damage similar to rising damp in a building and often appears in similar places. This is because it occurs in the "dead air" pockets that accumulate in both horizontal and vertical corners (ie out of circulating air patterns). One very important clue is that the damage due to rising damp tends to horizontal corners close to the ground whereas that due to condensation occurs at all levels.Another important clue is the possible lack of ventilation devices in the building (eg fans in bathrooms and toilets and cooker hoods.)If it is suspected that the problem is condensation, then a room should be sealed off with a dehumidifer left running for the recommended time and then further instrument tests made. If the dampness has disappeared, then condensation is very likely the problem. Insulation of cold surfaces and/or the elimination of water vapour at source are the answers.

Other possible problems

Water can penetrate the building due to structural defects and appear inside. Likely causes are:-
Roof defects such as faulty flashing, cracked or missing slates or tiles.
Faults in the brickwork or masonary such as missing or cracked pointing. Porous bricks or stones.
Missing or defective mastic around windows and doors.
Blocked weep holes.
Missing or defective trays in cavity walls.
Cement lodged on cavity wall ties forming a bridge allowing moisture to cross between inner and outer leafs.
Solid, ie non-cavity walls)
Damp proof course been buried by later building activities.

All of the above should be considered/repaired before remedial work on the damp proof course is undertaken.


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Damp (structural) — For other uses, see Damp (disambiguation). Detail showing some of the causes of damp penetration Structural dampness refers to the presence of unwanted moisture in the structure of a building, either the result of intrusion from outside or… …   Wikipedia

  • Damp (disambiguation) — Damp is an alternate term for Moisture. Damp or DAMP may also refer to: Damp (structural) Damp, Germany, a municipality in Schleswig Holstein, Germany Damp (album), a compilation album by Foetus Damp (mining), a gaseous product formed in coal… …   Wikipedia

  • art conservation and restoration — Maintenance and preservation of works of art, their protection from future damage, deterioration, or neglect, and the repair or renovation of works that have deteriorated or been damaged. Research in art history has relied heavily on 20th and… …   Universalium

  • Venice — /ven is/, n. 1. Italian, Venezia. a seaport in NE Italy, built on numerous small islands in the Lagoon of Venice. 361,722. 2. Gulf of, the N arm of the Adriatic Sea. 3. a town in SW Florida. 12,153. * * * I Italian Venezia City (pop., 2001 prelim …   Universalium

  • Roof — A roof is the covering on the uppermost part of a building. A roof protects the building and its contents from the effects of weather. Structures that require roofs range from a letter box to a cathedral or stadium, dwellings being the most… …   Wikipedia

  • Business and Industry Review — ▪ 1999 Introduction Overview        Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… …   Universalium

  • Europe, history of — Introduction       history of European peoples and cultures from prehistoric times to the present. Europe is a more ambiguous term than most geographic expressions. Its etymology is doubtful, as is the physical extent of the area it designates.… …   Universalium

  • arts, East Asian — Introduction       music and visual and performing arts of China, Korea, and Japan. The literatures of these countries are covered in the articles Chinese literature, Korean literature, and Japanese literature.       Some studies of East Asia… …   Universalium

  • Bulgaria — /bul gair ee euh, bool /, n. a republic in SE Europe. 8,652,745; 42,800 sq. mi. (110,850 sq. km). Cap.: Sofia. * * * Bulgaria Introduction Bulgaria Background: The Bulgars, a Central Asian Turkic tribe, merged with the local Slavic inhabitants in …   Universalium

  • Life Sciences — ▪ 2009 Introduction Zoology       In 2008 several zoological studies provided new insights into how species life history traits (such as the timing of reproduction or the length of life of adult individuals) are derived in part as responses to… …   Universalium

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.