Semiwadcutter

A semiwadcutter or SWC is a type of all purpose bullet commonly used in revolvers. The SWC combines features of the wadcutter target bullet and traditional round nosed revolver bullets, and is used in both revolver and pistol cartridges for hunting, target shooting, and plinking.

The basic SWC design consists of a roughly conical nose, truncated with a flat point, sitting on a cylinder (A at right). The base of the cone is slightly smaller in diameter than the cylinder, leaving a sharp shoulder. The flat nose punches a clean hole in the target, rather than tearing it like a round nose bullet would, and the sharp shoulder enlarges the hole neatly, allowing easy and accurate scoring of the target. The SWC design offers better external ballistics than the wadcutter, as its conical nose produces less drag than the flat cylinder. A typical modification is to alter the conical section to make the sides concave, to reduce the bullet mass, or convex, to increase it. B shows a concave sided SWC, typical of a lightweight .45 ACP bullet used in bullseye shooting. The concave sides reduce the bullet weight, and thus the recoil, while keeping the overall length of the bullet long enough to feed reliably in a semi-automatic pistol such as the M1911 commonly found in bullseye competitions.

Some of the most famous SWC designs were developed by Elmer Keith for use in handgun hunting. These designs (C) use a wider front, and convex sides on the "cone" in front. This puts more weight in the front of the bullet, allowing a heavier bullet with no reduction in case capacity. Since Keith was a prime motivating force in the development of the first magnum handgun cartridge, the .357 Magnum, he was very interested in maximizing the amount of case volume for the slower burning powders needed to push heavy bullets at high velocities. The choice of bullet for the .357 Magnum cartridge varied during its development. During the development at Smith & Wesson, the original Keith bullet was modified slightly, to the form of the Sharpe bullet, which itself was based upon the Keith bullet, but which had 5/6 of the bearing surface of the Keith bullet, Keith bullets typically being made oversized and sized down. Winchester, however, upon experimenting further during the cartridge development, modified the Sharpe bullet shape slightly, while keeping the Sharpe contour of the bullet. The final choice of bullet for the .357 Magnum was thus based on the earlier Keith and Sharpe bullets, while additionally having slight differences from both.cite book |author=Sharpe, Phillip B. |title = Complete Guide to Handloading |year=1937 |pages = 293-294]

The Keith style SWC has been taken even further, to produce designs that are nearly wadcutters in shape (D), but are intended for large game hunting with handguns. These have nearly cylindrical noses, which are as long as the firearm chamber allows, and just slightly smaller than bore diameter so they will easily chamber. The massive nose provides a large surface area for producing large wound channels, resulting in rapid incapacitation, and the heavy bullet provides excellent penetration. The wide nose is less prone to deformation than a narrow nose, allowing the bullet to keep its shape and continue to penetrate even if it encounters bone.

ee also

* Wadcutter

References

* [http://www.handgunsmag.com/ammunition/44mag_081005/ Reloading the .44 Magnum] by Patrick Sweeney, "Handguns" magazine


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Bullet — This article is about firearms projectiles. For other uses, see Bullet (disambiguation). Lead soft point, boat tailed, copper jacketed bullets A bullet is a projectile propelled by a firearm, sling, or air gun. Bullets do not normally contain… …   Wikipedia

  • Terminal ballistics — Terminal ballistics, a sub field of ballistics, is the study of the behavior of a projectile when it hits its target. It is often referred to as stopping power when dealing with human or other living targets. Terminal ballistics is as relevant… …   Wikipedia

  • Wadcutter — A wadcutter is a special purpose bullet specially designed for shooting paper targets, usually at close range and at subsonic velocities typically under 800 ft/s (244 m/s). They are often used in handgun and airgun competitions. A wadcutter has a …   Wikipedia

  • .41 Remington Magnum — Infobox Firearm Cartridge name= .41 Remington Magnum caption= origin= USA type= Revolver service= used by= wars= designer= Elmer Keith / Bill Jordan design date=1964 manufacturer=Remington Arms production date= number= variants= is SI specs=… …   Wikipedia

  • Revolver — A revolver is a repeating firearm that consists of multiple chambers and at least one barrel for firing. As the user cocks the hammer, the cylinder revolves to align the next round with the barrel, which gives this type of firearm its name. In… …   Wikipedia

  • .480 Ruger — Infobox Firearm Cartridge name= .480 Ruger caption= origin= USA type= Handgun designer= Hornady / Sturm, Ruger design date=2003 manufacturer= production date= number= variants= is SI specs= parent=.45 70 case type=Semi rimmed, straight… …   Wikipedia

  • Smith & Wesson Model 57 — Infobox Weapon name= Smith Wesson Model 57 caption= origin=flag|United States type=Revolver is ranged=yes service= used by= wars= designer= design date= manufacturer=Smith Wesson production date= 1964 present number= variants=see variants… …   Wikipedia

  • Основные типы пуль — AP Armor Piercing бронебойная 1 оболочка (сталь, томпак, латунь) 2 свинец 3 твердосплавный бронебойный сердечник BT Boat Tail винтовочная пуля с конусной хвостовой частью CP Cone Point с конической головной частью FMJ Full Metal Jacketed… …   Энциклопедия стрелкового оружия

  • Charles Bowden (criminal) — Charles Bowden is a convicted Irish criminal, who after turning state s witness in the murder of journalist Veronica Guerin, was the first person to enter the Republic of Ireland s witness protection programme.[1] Born in Finglas, Dublin, he left …   Wikipedia

  • Swaging — (  /ˈsweɪ …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.