Monopulse radar is an adaptation of conical scanning radar which sends additional information in the radar signal in order to avoid problems caused by rapid changes in signal strength. The system also makes jamming more difficult. Most radars designed since the 1960s are monopulse systems.

## Description

### Conical scan

Conical scanning is not considered to be a form of monopulse radar, but the following summary provides background that can aid understanding.

Conical scan systems send out a signal slightly to one side of the antenna's boresight, and then rotating the feed horn to make the lobe rotate around the boresight line. A target centered on the boresight is always slightly illuminated by the lobe, and provides a strong return. If the target is to one side, it will be illuminated only when the lobe is pointed in that general direction, resulting in a weaker signal overall (or a flashing one if the rotation is slow enough). This varying signal will reach a maximum when the antenna is rotated so it is aligned in the direction of the target, by looking for this maximum and moving the antenna in that direction, a target can be automatically tracked.

One problem with this approach is that radar signals often change in amplitude for reasons that have nothing to do with beam position. Over the period of a few tenths of seconds, for instance, changes in target heading, rain clouds and other issues can dramatically affect the returned signal. Since conical scanning systems depend on the signal growing or weakening due only to the position of the target relative to the beam, such changes in reflected signal can cause it to be "confused" about the position of the target within the beam's scanning area.

Jamming a conical scanner is also relatively easy. The jammer simply has to send out signals on the radar's frequency with enough strength to make it think that was the strongest return. In this case a series of random short bursts of signal will appear to be a series of targets in different locations within the beam. Jamming of this sort can be made more effective by timing the signals to be the same as the rotational speed of the feed, but broadcast at a slight delay, which results in a second strong peak within the beam, with nothing to distinguish the two. Jammers of this sort were deployed quite early, the British used them during World War II against the German conical-scanning Würzburg radar.

### Monopulse basics

Monopulse radars are similar in general construction to conical scanning systems, but add one more feature. Instead of broadcasting the signal out of the antenna "as is", they split the beam into parts and then send the two signals out of the antenna in slightly different directions. When the reflected signals are received they are amplified separately and compared to each other, indicating which direction has a stronger return, and thus the general direction of the target relative to the boresight. Since this comparison is carried out during one pulse, which is typically a few microseconds, changes in target position or heading will have no effect on the comparison.

Making such a comparison requires that different parts of the beam be distinguished from each other. Normally this is achieved by splitting the pulse into two parts and polarizing each one separately before sending it to a set of slightly off-axis feed horns. This results in a set of lobes, usually two, overlapping on the boresight. These lobes are then rotated as in a normal conical scanner. On reception the signals are separated again, and then one signal is inverted in power and the two are then summed. If the target is to one side of the boresight the resulting sum will be positive, if it's on the other, negative.

If the lobes are closely spaced, this signal can produce a high degree of pointing accuracy within the beam, adding to the natural accuracy of the conical scanning system. Whereas classical conical scan systems generate pointing accuracy on the order of 0.1 degree, monopulse radars generally improve this by a factor of 10, and advanced tracking radars like the AN/FPS-16 are accurate to 0.006 degrees. This is an accuracy of about 10 m at a distance of 100 km.

Jamming resistance is greatly improved over conical scanning. Filters can be inserted to remove any signal that is either unpolarized, or polarized only in one direction. In order to confuse such a system, the jamming signal would have to duplicate the polarization of the signal as well as the timing, but since the aircraft receives only one lobe, determining the precise polarization of the signal is difficult. Against monopulse systems, ECM has generally resorted to broadcasting white noise to simply blind the radar, instead of attempting to produce false localized returns.

#### Antenna Sampling

Monopulse antennas produce a sum signal and two delta signals. This allows angular measurement to be performed using a single receive pulse. The sum signal usually passes back down the waveguide used to send the transmit pulse. The two delta signals are elevation (up-down) and traverse (left-right).

The sum signal corresponds with the antenna beam along center-line of the antenna. The delta signals are pairs of beams that are adjacent to the center-line of the sum antenna beam. The delta beam measurements produce plus or minus values depending upon the quadrant.

The sum signal is created by a feedhorn structure positioned to maximize signal at the center of the antenna beam. The delta RF signals are created by pairs of antenna feed-horns located adjacent to the sum feed-horn (sum feed-horn not shown in the figure). The output of each pair of delta feed-horns are added together, and this creates zero output signal when the incoming RF signal is located at the center of the antenna beam. The signal strength from each delta beam increases as the aircraft drifts further away from the antenna center-line.

For the waveguide image that is shown, a horizontally polarized RF signal arrives at the two feed horns to produce a left/right delta signal. The arriving energy from the RF wavefront is launched into both waveguide feedhorns. The RF signal from both feedhorns travels up the waveguide where the signals from the left and right feedhorn are combined. The combiner performs a mathematical subtraction on the electrical signals arriving from the feedhorns. That subtraction produces the delta signal. A similar feedhorn configuration is used to produce the up/down delta signal (not shown). The waveguide assembly can be used by itself. For a high gain antenna, the feedhorn assembly is located facing the reflecting surface at or near the focal point.

For the waveguide image that is shown, the sum signal would be created by a single waveguide feedhorn centered between the two feedhorns that are shown.

The sum and delta radio frequency signals are converted to a lower frequency in the receiver where sampling takes place. A signal processor produces the error signal using these samples.

The + or - value for each delta signal is created by phase shift of 0 degrees or 180 degrees when compared with the sum signal. A calibration signal is injected into the receive path when the radar is idle, and this establishes a known phase shift between different microwave signal paths (quiescent mode).

The angle error is created from the delta signal by performing a complex ratio. This is done for the left/right delta beams, and this is also done for the up/down delta beams (two ratios). An explanation of how real and imaginary parts are used with RADAR can be found in the description of Pulse Doppler.

$Error = \left (\frac{(Real Delta) + i (Imaginary Delta)}{(Real Sum) + i (Imaginary Sum)} \right) \div \left (\frac{(Real Delta Cal) + i (Imaginary Delta Cal)}{(Real Sum Cal) + i (Imaginary Sum Cal)} \right)$

The result is a signed number. The outcome of the calibration process is to rotate the complex antenna angle error vector onto the real axis to reduce signal processing losses.

The angle error is used to make an adjustment to position the target along the centerline of the antenna. On mechanically steered radar, the vertical angle error drives a motor that moves the antenna up or down, and the horizontal angle error dries a motor that steers the antenna left or right. On a missile, the angle error is an input to the guidance system that positions the guidance fins that rotate the body of the missile so that the target is in the centerline of the antenna.

A wheel, mirror and a light can be used to visualize real and imaginary described in this equation. The mirror is placed at a 45 degree angle above the wheel so that you can see the front and top of the wheel at the same time. The light is attached to the wheel so that you can see the wheel when the room lights are turned off. You sit directly in front of the wheel while a friend rotates the wheel. The view of the front of the wheel (real) and the top of the wheel (imaginary) tell you the position of the wheel.

Pairs of real and imaginary values form a complex number explained as real and imaginary parts.

Dynamic calibration is needed when there are long waveguide runs between the antenna and first down converter (see Superheterodyne_receiver). This compensates for temperature changes that alter the size and length of wave-guide, which will cause phase variations that produce incorrect angle error signals for long wave-guide runs. The Cal term is created by injecting a calibration signal into the receive waveguide while the system is not active (sum and delta). The angle error of the calibration signal is used to evaluate angle error during normal operation. Antenna tuning is used to make adjustments that create the desired error signal when the antenna is calibrated on an antenna range.

When the waveguide run is short between the antenna and receiver, the calibration signal can be omitted and the calibration term can be set to a fixed value. A fixed value may also be stored for systems with long wave-guide runs to allow degraded operation when RF calibration cannot be performed. The waveguide assembly may need to be tuned using an antenna range to obtain consistent results.

Monopulse gives much better target azimuth measurements than the estimating of the angular position shown in figure 1. It can operate at a much lower interrogation rate to benefit others in the environment. Monopulse systems usually contain enhanced processing to give better quality target code information. A single pulse contains all of the information required for an angle error measurement (hence the use of the term monopulse). The elements in linear antenna array are divided into two halves. These two separate antennae arrays are placed symmetrically in the focal plane on each side of the axis of the radar antenna (this often called boresight axis). In transmission (Tx) mode, both antennae arrays will be fed in phase and the radiation pattern is represented by the ice blue area, which is called the Σ or Sum -diagram. (shown in the Figure as blue graph and pattern) In reception (Rx) mode an additional receiving way is possible. From the received signals of both separate antenna arrays, it is possible to calculate Σ (like the transmitted Sum -diagram) and the difference ΔAz, the so called Delta azimuth- diagram. The antenna pattern is given by the red and green area on the same figure. Both signals are then compared as a reply processor function and their difference is used to estimate the azimuth of the target more exactly. The angle between the axis of the antenna (boresight axis) and the direction of the target is also known as OBA-value (Off-Boresight Angle). The elevation angle is also measured at 3D radars as a third coordinate. Well, the procedure is used twice now. Here the antenna is derived in addition in an upper half and a lower half. The second difference channel (ΔEl) is called „Delta Elevation” now. II

+ΔEl -ΔAz



I

+ΔEl+ΔAz



III

-ΔEl -ΔAz



IV

-ΔEl+ΔAz



Figure 5: the four quadrants of a monopulse antenna The Monopulse antenna is divided up into four quadrants now: The following signals are formed from the received signals of these four quadrants: Sum - signal Σ ( I + II + III + IV ) Difference - signal ΔAz ( I + IV ) - ( II + III ) Difference - signal ΔEl ( I + II ) - ( III + IV ) The · Auxiliary Signal Ω also shall to complete the picture be mentioned, although this one isn't tied to the monopulse antenna. This channel to the compensation of side lobes always has practically his own small antenna and has a very wide antenna diagram and also serves for the reconnaissance of active jamming. All these signals need an own receiver channel.

### Antenna Positioning

Tracking systems produce constant aircraft position information, and the antenna position is part of this information. Antenna error signals are used to create feedback as part of a RADAR system that can track aircraft.

The horizontal signal and the vertical signal created from antenna RF samples are called angle errors. These angle error signals indicate the angular distance between the center of the antenna beam and the position of the aircraft within the antenna beam.

For a mechanically steered antenna, the horizontal signal and vertical signal are used to create a drive signal that creates torque for two antenna positioning motors. One motor moves the antenna left/right. The other motor drives the antenna up/down. The result is to move the antenna position so that the center of the antenna beam remains aimed directly at the aircraft even when the aircraft is moving perpendicular to the antenna beam.

For a track while scan radar, position and velocity is maintained for multiple aircraft. The last position of the aircraft is coasted using the velocity, and that information is used to direct a beam of energy toward the aircraft. The monopulse angle error information that is received is used to adjust the position and velocity data for the aircraft. This is a common mode with phased array radar systems.

Amplitude-Comparison Monopulse provides an explanation of the antenna signals involved in this process.

#### Doppler

Doppler effect can be used to separate different objects based on speed. Pulse Doppler RADAR signal processing uses this technique. This is combined with conical scanning or monopulse to improve track reliability. It is necessary to separate the object signal from the interference to avoid being pulled off the object. This avoids problems where the system is fooled by aircraft flying to close to the surface of the earth or aircraft flying through clouds.

Conical scan and monopulse antennas are susceptible to interference from weather phenomenon and stationary objects. The resulting interference can produce feedback signals that move the antenna beam away from the aircraft. This can produce an unreliable antenna position when the antenna is aimed too near the ground or too near to heavy weather. Systems with no Pulse Doppler tracking mode may remain aimed at irrelevant objects like trees or clouds. Constant operator attention is required when there is no Doppler signal processing.

## History

Monopulse radar was extremely "high tech" when it was first introduced by Robert M. Page in 1943 in a Naval Research Laboratory experiment. As a result, it was very expensive, labor-intensive due to complexity, and less reliable. It was only used when extreme accuracy was needed that justified the cost. Early uses included the Nike Ajax missile, which demanded very high accuracy, or for tracking radars used for measuring various rocket launches. An early monopulse radar development, in 1958, was the AN/FPS-16, on which NRL and RCA collaborated. The earliest version, XN-1, utilised a metal plate lens. The second version XN-2 used a conventional 3.65 meter [12 ft] parabolic antenna, and was the version which went to production. These radars played an important part in the Mercury, Gemini, and early Apollo missions, being deployed in Bermuda, Tannarive, and Australia, among other places for that purpose. The IRACQ [Increased Range ACQuisition] modification was installed on certain of these installations; certainly the one located at Woomera, Australia was so modified. One of the larger installations first appeared in the 1970s as the US Navy's AN/SPY-1 radar used on the Aegis Combat System, and MK-74 radar used used on Tartar Guided Missile Fire Control System and research[1]. The cost and complexity of implementing monopulse tracking was reduced and reliability increased when digital signal processing became available after the 1970s, and the technology is today found in most modern tracking radars, and in many types of disposable ordnance like missiles.

## References

1. ^ [www.jhuapl.edu/techdigest/TD/td1804/zinger.pdf Mountaintop]

• Amplitude monopulse

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• monopulse radar — noun any radar that is capable of estimating the position of a target based on the return of a single pulse from a cluster of simultaneous beams …   Wiktionary

• nonscanning monopulse radar — A terrain radar that provides pitch rate error signals to a command indicator for manual control of aircraft in the pitch axis. The resultant flight path aims to parallel or follow the terrain at a height setting that is adjustable in flight.… …   Aviation dictionary

• scanning monopulse radar — A terrain radar that scans the terrain ahead of the aircraft and determines the elevation the aircraft must follow to clear the ground by the required height. Aircraft at correct height. Aircraft below safe height. Radar indicates need to climb …   Aviation dictionary

• Radar à balayage conique — Radar monopulse Le radar monopulse est une adaptation du radar à balayage conique qui envoie des informations supplémentaires dans le signal pour éviter les problèmes posés par les changements rapides de la force du signal. Le système permet… …   Wikipédia en Français

• Radar Primaire — typique d un aéroport Un radar primaire (Primary Surveillance Radar ou PSR en anglais) est un capteur radar classique qui illumine une large portion d’espace avec une onde électromagnétique et qui reçoit en retour les ondes réfléchies par les… …   Wikipédia en Français

• Radar primaire — typique d un aéroport Un radar primaire (Primary Surveillance Radar ou PSR en anglais) est un capteur radar classique qui illumine une large portion d’espace avec une onde électromagnétique et qui reçoit en retour les ondes réfléchies par les… …   Wikipédia en Français

• RADAR — Pour les articles homonymes, voir Radar (homonymie). Cette antenne radar longue portée, connue sous le nom ALTAIR, est utilisée pour détecter et pister les objets spatiaux …   Wikipédia en Français

• Radar embarqué — Radar Pour les articles homonymes, voir Radar (homonymie). Cette antenne radar longue portée, connue sous le nom ALTAIR, est utilisée pour détecter et pister les objets spatiaux …   Wikipédia en Français

• Radar OTH — Radar trans horizon Un radar trans horizon, ou Over the horizon radar (OTH) est un équipement radar qui permet le repérage d une cible à très longue distance, de l ordre de quelques milliers de kilomètres. Sommaire 1 Principe de fonctionnement 2… …   Wikipédia en Français