- For the Transformers character see Double Clutch (Transformers).
A double clutch (also called a double declutch) is a driving procedure primarily used for vehicles with an unsynchronized manual transmission. The double clutching technique involves the following steps:
- The throttle is released, the clutch pedal is pressed, and the gearbox is shifted into neutral.
- The clutch pedal is then released, the driver matches the engine RPM to the gear RPM either by throttle or wait for RPM to decrease until they are at a level suitable for shifting into the next gear.
- At the moment when the revs between engine and gear are closely matched, the driver then instantly depresses the clutch again and shifts into the next gear. The whole maneuver can, with practice, take no more than a fraction of a second, and the result is a very smooth gear change.
Manual transmission shifting
In a gearbox with neutral between each gear, a typical shift actually involves two gear changes, once into neutral, and again into the next gear. During any shift, disconnecting drive components via a clutch properly unloads the engine and transmission of undue pressure applied by the opposing components. Fully utilizing the clutch for each shift out of, and then into each gear is double clutching. Due to the absence of a neutral spacing, double clutching is ill-advised for sequential gear changes, as in a fully sequential gearbox such as a typical motorcycle.
Keeping the clutch pedal pressed while in neutral, as is performed during a typical shift, gives more economy of driver motion and effort compared to double clutching. Taken to extreme, sequential gearbox shifts and non-clutched shifts are also very quick and effortless. However, significant wear can take place on the separated clutch plates any time the engine and transmission have varying drive loads. In simple terms, wear occurs the more the clutch has to "slip" to match revolutions between the engine and transmission. Double clutching can minimize this clutch plate wear by encouraging matching of engine and transmission RPMs before the clutch plates are engaged.
History and theory
Before the introduction of transmission synchronizers (in the 1920s) and helical cut gears, double clutching was a technique required to prevent damage to an automobile's gear system. Due to the difficulty and most often unnecessary redundancy involved in learning the technique, coupled with the advent of synchronized gearing systems, it has largely fallen into disuse. However, drivers of large trucks often use the double clutching technique when unable to keep the transmission unloaded during shifting, as large vehicles are usually equipped with older, simpler and more durable unsynchronized gearboxes.
The purpose of the double-clutch technique is to aid in matching the rotational speed of the input shaft being driven by the engine to the rotational speed of the gear you wish to select (directly connected to rotating wheels). When the speeds are matched, the gear will engage smoothly and no clutch is required. If the speeds are not matched, the dog teeth on the collar will "crash" or grate as they attempt to fit into the holes on the desired gear. A modern synchromesh gearbox accomplishes this synchronization more efficiently. However, when the engine speed is significantly different than the transmission speed, the desired gear can often not be engaged even in a fully synchronized gearbox. An example is trying to shift into a gear while travelling outside the gear's speed or directional range, such as accidentally into 1st from near the top of 2nd, or intentionally from reverse to a forward gear whilst still moving at speed.
Double clutching, although time consuming, eases gear selection when an extended delay or variance exists between engine and transmission speeds.
Although double clutching is a testing requirement when obtaining a commercial driver's license, many experienced truckers have learned when it is possible to shift gears without using the clutch. This is known as float gears or skip shift, which thus eliminates the clutch except for starting and stopping.
Conversely, in order to shift down, engine RPM must be increased while the gearbox is in neutral and the clutch is either engaged or disengaged. This requires the driver to shift into neutral, apply throttle to bring the RPM up to a suitable speed, and finally shift into gear. This operation can be very difficult to master, as it requires the driver to gauge the speed of the vehicle and throttle accurately. Double clutching occurs if the clutch pedal is released while matching engine speeds in neutral and again engaged prior to shifting into the next gear.
A related downshifting technique is called heel-and-toe, in which the brake and accelerator pedals are pressed simultaneously. Classically, the brake is pressed with the ball of the right foot and the accelerator pedal is controlled by the right heel, while the clutch pedal is pressed by the left foot. However, many variants are possible, with the brake and accelerator pressed by sides of the right foot.
Proper heel-and-toe technique aids both slowing the vehicle while at the same time accelerating the engine for a matched downshift. Note that neglecting to rev-match in any downshifting scenario can be extremely dangerous, especially in low-traction conditions. Heel-and-Toe may be used with any type of gearbox when simultaneous braking and downshifting is necessary. Though difficult, mastering the heel-and-toe technique in conjunction with necessary clutching is essential for high performance driving (e.g., rally racing) to stay in the optimal gear regardless of the simultaneous braking, accelerating, and clutching required for shifts. This allows the engine to stay in the RPM "powerband" and allows one to drive as fast as possible. Left foot braking while accelerating the engine with the right foot to accommodate downshifting in a clutchless situation accomplishes the same feat.
The purpose of the heel-toe-double-clutch is to downshift into the correct gear, and thus optimal engine RPM, for exiting the corner while placing the least wear and tear on the entire drivetrain. Note that racers will sometimes skip gears during downshifts depending on the vehicle speed. With double-clutching there is no need to shift through every gear when significant velocity has been lost.
- Video of heel-toe braking in conjunction with double-clutch downshifts in a racecar. (.WMV)
- What's All This Double-Clutching Stuff, Anyhow? (another detailed description and reasons for double clutching)
Wikimedia Foundation. 2010.
Look at other dictionaries:
Double Clutch — Éditeur Sega Développeur Ascii Date de sortie 1992 Genre Course Mode de jeu Un à deux joueur(s) … Wikipédia en Français
double-clutch — double clutch1 /dub euhl kluch /, v.i. Auto. to downshift by shifting gears in an automotive vehicle first into neutral and then into the desired gear, releasing the clutch twice, once for each shift. double clutch2 /dub euhl kluch /, v.i. (of a… … Universalium
double-clutch — | ̷ ̷ ̷ ̷| ̷ ̷ intransitive verb Etymology: double (I) + clutch, n. : to shift gear in an automotive vehicle usually to a lower speed by shifting first into neutral and then to the speed required with the clutch being released each time … Useful english dictionary
double-clutch — intransitive verb Date: 1928 to shift gears in an automotive vehicle by shifting into neutral and pumping the clutch before shifting to another gear … New Collegiate Dictionary
double clutch — See double clutching … Dictionary of automotive terms
Double Clutch (Transformers) — Double Clutch is the name of two Autobot fictional characters from the Transformers. Contents 1 Transformers: Generation 2 1.1 Fun Publications 1.2 Toys 2 Transformer … Wikipedia
Clutch control — refers to the act of controlling the speed of a vehicle with a manual transmission by partially engaging the clutch plate, using the clutch pedal instead of (or in conjunction with) the accelerator pedal. The purpose of a clutch is in part to… … Wikipedia
clutch —  An electrically operated coupling device that connects or disconnects the compressor pulley and compressor shaft  A device that disconnects the engine from the transmission, to allow the vehicle to change gears, and then allows the engine… … Dictionary of automotive terms
Clutch — For other uses, see Clutch (disambiguation). Rear side of a Ford V6 engine, looking at the clutch housing on the flywheel … Wikipedia
Clutch (G.I. Joe) — G.I. Joe character Clutch Affiliation G.I. Joe Specialty Driver File name … Wikipedia