High-speed multimedia radio

High-speed multimedia radio (HSMM), colloquially referred to as "the hinternet", is the implementation of wireless data networks over amateur radio frequencies using commercial off-the-shelf (COTS) hardware such as 802.11 access points and D-Star equipment. Licensed amateur radio operators may use amplifiers and specialized antennas to increase the power and coverage of the 802.11 signal.

The name "hinternet" comes from a combination of the words "ham" and "Internet" and can be used to refer to any high speed data network over amateur radio, not just 802.11 networks.


The idea behind this implementation is to use the 900 MHz (33 cm), 2.4 GHz (13 cm), 3.4 GHz (9 cm), and 5.8 GHz (5 cm) amateur radio bands under the FCC Part 97 rules (amateur radio service) instead of the Part 15 rules (unlicensed). This enables amateur operators to legally use higher output power for wireless devices and allows for longer-range communications. Such communications can be used to assist in emergency communications and disaster relief operations and in everyday amateur radio communications.

What can it do?

The "hinternet" can support most of the traffic that the Internet currently does, including video chat, voice, instant messaging, the Web (HTTP), file transfer (FTP), and forums. The only differences being that on the hinternet such services are community instead of commercially implemented and the "hinternet" is "mostly" wireless. The hinternet can even be connected to the Internet and used for "Web surfing", although because of the FCC regulations on permitted content, this is rarely done. Using high gain antennas and amplifiers, reliable long-distance wireless links over many miles are possible and only limited by the radio horizon.

Frequencies and channels

The following is a list of the 802.11 channels that overlap into an amateur radio band under the FCC in the United States. Note that the 5 cm amateur band extends from 5650 to 5925 MHz, so that there are many frequencies outside the Part 15 ISM/UNII block used for 802.11a. Some equipment can be programmed to operate on these “extra” channels, and some cannot. Many commercial grade 802.11a access points can also operate in between the normal channels by using 5 MHz channel spacing instead of the standard 20 MHz channel spacing. 802.11a channels 132, 136 and 140 are only available for unlicensed use in ETSI regions.

The following images show the overlapping relationship of the Part 15 unlicensed bands and the Part 97 licensed bands. The images are not to scale.

2.4 GHz 802.11b/g

5.8 GHz 802.11a

Channels and power


:The 802.11a amateur radio band consists of twelve "non-overlapping" channels in the 5.650–5.925 GHz (5 cm) band. The 802.11a standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11a hardware is not subject to the power rules in FCC [http://www.arrl.org/FandES/field/regulations/news/part97/d-305.html#311 Part 97 § 97.311] and the maximum allowable output power is 1500 watts (W) PEP.


:The 802.11b amateur radio band consists of eight "overlapping" channels in the 2.390–2.450 GHz (13 cm) band. The 802.11b specification uses Direct Sequence Spread Spectrum (DSSS) to transmit data and is subject to the rules of FCC [http://www.arrl.org/FandES/field/regulations/news/part97/d-305.html#311 Part 97 § 97.311] . Therefore the maximum allowable power output is 100 W PEP. If the transmitter power exceeds 1 W, the station must use automatic power control.


:The 802.11g amateur radio band consists of eight "overlapping" channels in the 2.4 GHz (13 cm) band. The 802.11g standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11g hardware is not subject to the power rules in FCC [http://www.arrl.org/FandES/field/regulations/news/part97/d-305.html#311 Part 97 § 97.311] and the maximum allowable output power is 1500 W PEP.

Frequency sharing


:The 5 cm band is shared with the fixed-satellite service in ITU Region 1, and the radiolocation service. In ITU Region 2 (US) the primary user is military radiolocation, specifically naval radar. Amateur radio operators have secondary privileges to the Federal radiolocation service in the entire band and may not cause interference to these users. Amateur operators are allocated this band are in a co-secondary basis with ISM devices and space research. Amateur, space research, and ISM operators each have the "right to operate". Due to the lack of a high number of Part 15 users (compared to 2.4 GHz), the noise level tends to be lower in many parts of the US but can be quite congested in urban centers and on mountaintops.


:The 13 cm band is shared with Part 15 users as well as the Federal radiolocation service, and ISM (industrial, scientific, medical) devices. Amateur radio operators have secondary privileges to the Federal radiolocation service in the entire band and may not cause interference to these users. Amateur radio operators have primary privileges to ISM devices from 2.390–2.417 GHz and secondary privileges from 2.417–2.450 GHz. Because of the high number of Part 15 users, the noise level in this band tends to be rather high.


:As with any amateur radio mode stations must identify at least once every 10 minutes. One acceptable method for doing so is to transmit one’s call sign inside an ICMP echo request (commonly know as a ping). If the access point is set to "master" then the user’s call sign may be set as the "SSID" and therefore will be transmitted at regular intervals.

:It is also possible to use a DDNS "push" request to automatically send an amateur callsign in plain text (ASCII) every 10 minutes. This requires that a computers hostname be set to the callsign of the amateur operator and that the DHCP servers lease time be set to less than or equal to 10 minutes. With this method implemented the computer will send a DNS "push" request that includes the local computers hostname every time the DHCP lease is renewed. This method is supported by all modern operating systems including but not limited to Windows, OSX, BSD, and Linux.

:802.11 hardware may transmit and receive the entire time it is powered on even if the user is not sending data.


:Because amateur transmissions may not be encoded or encrypted in any way, security measures that are implemented must be published. This makes it very difficult to keep unauthorized users from accessing HSMM networks, although casual eavesdroppers can effectively be deterred. Current schemes include using MAC address filtering, WEP and WPA/WPA2. MAC address filtering and WEP are all hackable by using freely available software from the Internet, making them the less secure options. Per FCC rules the encryption keys themselves must be published in a publicly accessible place if using WEP, WPA/WPA2 or any other encryption, thereby undermining the security of their implementation.:Using professional or modified hardware it is possible to operate on 802.11a channels that are outside the FCC authorized Part 15 bands but still inside the 5.8 GHz (5 cm) amateur radio band. Transverters or "frequency converters" can also be used to move HSMM 802.11b/g operations from the 2.4 GHz (13 cm) band to the 3.4 GHz (9 cm) amateur radio band.

Custom frequencies

:Using professional grade commercial hardware or modified consumer grade hardware it is possible to operate 802.11 on channels that are outside of the normal FCC allocated frequencies for unlicensed users but still inside an amateur radio band. Some of these frequencies are inside the 2.4 GHz (13 cm), 3.4 GHz (9 cm) and the 5.8 GHz (5 cm) amateur radio bands, thereby providing better security and interference characteristics to amateur radio operators. While using amateur-only frequencies all but alleviates the security concerns of using 802.11, the relative high cost of such devices is a large deterrent to their widespread deployment.

2.4 GHz custom frequencies

:Using professional grade hardware or modified consumer grade hardware it is possible to operate on 802.11b/g hardware on channels that are effectively "0" at 2.407 GHz and "−1" at 2.402 GHz. Using these channels allows amateur operators to move away from unlicensed Part 15 operators but may interfere with AMSAT satellite downlinks near 2.400 GHz and 2.401 GHz.

3.4 GHz transverters

:Frequency conversion involves the use of transverters that convert the operating frequency of the 802.11b/g device from 2.4 GHz to another band entirely. Transverter is a technical term and is rarely used to describe these products which are more commonly known as "frequency converters", "up/down converters", and just "converters". Commercially-available converters can convert a 2.4 GHz 802.11b/g signal to the 3.4 GHz (9 cm) band which is not authorized for unlicensed Part 15 users.

5.8 GHz custom frequencies

:Using professional grade hardware or modified consumer grade hardware it is possible to operate on 802.11a channels 116–140 (5.57–5.71 GHz) and channels above 165 (> 5.835 GHz). These frequencies are outside of the FCC allocated Part 15 unlicensed band, but still inside of the 5.8 GHz (5 cm) amateur radio band. Modifying consumer hardware to operate on these expanded channels often involves installing after-market firmware and changing the "country code" setting of the wireless card. When buying professional grade hardware, many companies will authorize the use of these expanded frequencies for a small additional fee.

Custom firmware

One popular way to access amateur only frequencies is to modify an off-the-shelf access point with custom firmware. This custom firmware is freely available on the Internet from projects such as DD-WRT and Openwrt. The most popular piece of hardware that is modified is the Linksys WRT54GL because of the widespread availability both the hardware and third party firmware.

ee also

*Amateur radio emergency communications
*Amateur radio frequency allocations
*List of hsmm nodes
*Metropolitan Area Network
*Orthogonal frequency-division multiplexing
*Outernet server (software)
*Packet Radio
*Part 15
*Spread spectrum
*Tomato Firmware
*Ultra wideband
*Wireless Distribution System
*Wireless LAN

External links

* [http://www.arrl.org/hsmm/ High Speed Digital Networks and Multimedia] : "Official" ARRL Web page.
* [http://www.n5oom.org/hsmm/ N5OOM’s HSMM Projects] : Web page from W5OOM detailing several projects and implementations of HSMM.
* [http://www.jefatech.com/category/hsmm/ JEFA Tech] : Vendor supporting HSMM projects
* [http://www.fab-corp.com FAB-Corp] : A product vendor
* [http://www.outernet.cc The Outernet Project] : Project page for the Outernet HSMM server software


* [http://www.arrl.org/FandES/field/regulations/techchar/D-STAR.pdf D-Star System]
* [http://www.fcc.gov/Bureaus/Engineering_Technology/Documents/cfr/1998/47cfr97.pdf FCC Part 97 Rules]
* [http://www.fcc.gov/oet/info/rules/part15/part15-8-14-06.pdf FCC Part 15 Rules]
* [http://hraunfoss.fcc.gov/edocs_public/attachmatch/FCC-01-158A1.pdf FCC rejection of OFDM as Spread Spectrum]
* [http://www.wlanparts.com/product/SR9 Ubiquiti SR9 mini-PCI 900MHz SuperRange9]
* [http://www.cq-vhf.com/HSMM%20Spring%202003.html HSMM: Communicating Voice, Video, and Data with Amateur Radio]
* [http://www.cq-vhf.com/FallHSMMt.html HSMM and Information Security]
* [http://www.qsl.net/kb9mwr/projects/wireless/plan.html Using Part 15 Wireless Ethernet Devices For Amateur Radio]
* [http://www.moonblinkwifi.com/80211a_frequency_channel_map.cfm 802.11a Frequency Channel Map]
* [http://www.mikrotik.com/documentation/manual_2.7/Interface/Wireless.html MikroTik RouterOS manual]
* [http://www.cisco.com/univercd/cc/td/doc/product/access/mar_3200/wlsnotes/cfchannl.htm#wp1090091 5.0 GHz (802.11a/h) Channels and Frequencies]

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • High-Definition Multimedia Interface — Infobox connector name=High Definition Multimedia Interface type=Digital audio/video connector logo= caption=HDMI cable and HDMI official logo designer=HDMI Founders design date=December 2002 manufacturer=HDMI Adopters production date=2003… …   Wikipedia

  • Radio-frequency identification — (RFID) is a technology that uses radio waves to transfer data from an electronic tag, called RFID tag or label, attached to an object, through a reader for the purpose of identifying and tracking the object. Some RFID tags can be read from… …   Wikipedia

  • Amateur radio — Amateur radio, often called ham radio, is both a hobby and a service in which participants, called hams, use various types of radio communications equipment to communicate with other radio amateurs for public service, recreation and self training …   Wikipedia

  • General Packet Radio Service — (GPRS) is a packet oriented mobile data service on the 2G and 3G cellular communication system s global system for mobile communications (GSM). GPRS was originally standardized by European Telecommunications Standards Institute (ETSI) in response …   Wikipedia

  • Freedom of Mobile Multimedia Access — FOMA (IPA:/ foʊmə/), officially short for Freedom of Mobile Multimedia Access, is the brand name for the 3G services being offered by Japanese mobile phone operator NTT DoCoMo.FOMA was the world s first W CDMA 3G service when launched in 2001.… …   Wikipedia

  • Software-defined radio — A Software Defined Radio (SDR) system is a radio communication system where components that have typically been implemented in hardware (i.e. mixers, filters, amplifiers, modulators/demodulators, detectors. etc.) are instead implemented using… …   Wikipedia

  • interactive multimedia —       any computer delivered electronic system that allows the user to control, combine, and manipulate different types of media, such as text, sound, video, computer graphics, and animation. Interactive multimedia integrate computer, memory… …   Universalium

  • Bronx High School of Science — Infobox Secondary school name = The Bronx High School of Science native name = motto = Every great advance in science has issued from a new audacity of imagination John Dewey established = 1938 founder = Morris Meister city = Bronx state = NY… …   Wikipedia

  • Granby High School — Infobox School name= Granby High School imagesize= 300px motto= Home of the Comets streetaddress= 7101 Granby Street city= Norfolk state= Virginia zipcode= 23505 country= USA url= [http://ww2.nps.k12.va.us/education/school/school.php?sectionid=18/… …   Wikipedia

  • Citizens' band radio — Typical 1980s CB base station, used with outdoor antenna. This radio may also be used in an automobile, since it is powered by 13.8V DC. Shown with Astatic Power D 104 desk mic …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.