Adiabatic flame temperature
In the study of
combustion, there are two types of adiabatic flame temperature depending on how the process is completed: constant volume and constant pressure. The constant volume adiabatic flame temperature is the temperaturethat results from a complete combustionprocess that occurs without any work, heat transferor changes in kineticor potential energy.
The constant pressure adiabatic flame temperature is the temperature that results from a complete combustion process that occurs without any heat transfer or changes in kinetic or potential energy. Its temperature is lower than the constant volume process because some of the energy is utilized to change the volume of the system (i.e., generate work).
(It is a common fallacy that this is the maximum temperature that can be achieved for given
reactants because any heat transfer from the reacting substances and/or any incomplete combustion would tend to lower the temperature of the products. However, since the assumptions inherent in the adiabatic flame temperature assume chemical equilibrium, states in thermal equilibrium but not chemical equilibrium are not constrained by this limit. In fact, several fuel rich acetylene and methane flames have been found to exceed their adiabatic flame temperatures by hundreds of degrees.)
In daily life, the vast majority of
flamesone encounters are those of organic compounds including wood, wax, fat, common plastics, propane, and gasoline. The constant-pressure adiabatic flame temperature of such substances in air is in a relatively-narrow range around 1950°C. This is because, in terms of stoichiometry, the combustion of an organic compound with "n" carbons involves breaking roughly 2"n" C–H bonds, "n" C–C bonds, and 1.5"n" O2 bonds to form roughly "n" CO2 molecules and "n" H2O molecules.
Because most combustion processes that happen naturally occur in the open air, there is nothing that confines the gas to a particular volume like the cylinder in an engine. As a result, these substances will burn at a constant pressure allowing the gas to expand during the process.
Common flame temperatures
Assuming initial atmospheric conditions (1 bar and 20°C), the following table list the adiabatic flame temperature for various gases under constant volume conditions. The temperatures mentioned here are for a stoichiometric fuel-oxidizer mixture (i.e.
first law of thermodynamicsfor a closed reacting system we have,: where, and are the heat and work transferred during the process respectively, and and are the internal energy of the reactants and products respectively. In the constant volume adiabatic flame temperature case, the volume of the system is held constant hence there is no work occurring,: and there is no heat transfer because the process is defined to be adiabatic: . As a result, the internal energy of the products is equal to the internal energy of the reactants: . Because this is a closed system, the mass of the products and reactants is constant and the first law can be written on a mass basis,: .
In the constant pressure adiabatic flame temperature case, the pressure of the system is held constant which results in the following equation for the work,: Again there is no heat transfer occurring because the process is defined to be adiabatic: . From the first law, we find that,:Recalling the definition of enthalpy we recover: . Because this is a closed system, the mass of the products and reactants is constant and the first law can be written on a mass basis,: .
We see that the adiabatic flame temperature of the constant pressure process is lower than that of the constant volume process. This is because some of the energy released during combustion goes into changing the volume of the control system. One analogy that is commonly made between the two processes is through combustion in an internal combustion engine. For the constant volume adiabatic process, combustion is thought to occur instantaneously when the piston reaches the top of its apex (
Otto cycleor constant volume cycle). For the constant pressure adiabatic process, while combustion is occurring the piston is moving in order to keep the pressure constant ( Diesel cycleor constant pressure cycle).
If we make the assumption that combustion goes to completion (i.e. and ), we can calculate the adiabatic flame temperature by hand either at
stoichiometricconditions or lean of stoichiometry (excess air). This is because there are enough variables and molar equations to balance the left and right hand sides,
Rich of stoichiometry there are not enough variables because combustion cannot go to completion with at least and needed for the molar balance (these are the most common incomplete products of combustion),
However, if we include the
Water gas shift reaction,: and use the equilibrium constant for this reaction, we will have enough variables to complete the calculation.
Different fuels with different levels of energy and molar constituents will have different adiabatic flame temperatures.
We can see by the following figure why
nitromethaneis often used as a power boost for cars. Since it contains two moles of oxygen in its molecular makeup, it can burn much hotter because it provides its own oxidant along with fuel. This in turn allows it to build-up more pressure during a constant volume process. The higher the pressure, the more force upon the piston creating more work and more power in the engine. It is interesting to note that it stays relatively hot rich of stoichiometry because it contains its own oxidant. However, continual running of an engine on nitromethane will eventually melt the piston and/or cylinder because of this higher temperature.
In real world applications, complete combustion does not typically occur. Chemistry dictates that dissociation and
kineticswill change the relative constituents of the products. There are a number of programs available that can calculate the adiabatic flame temperature taking into account dissociation through equilibrium constants (Stanjan, NASA CEA, AFTP). The following figure illustrates that the effects of dissociation tend to lower the adiabatic flame temperature. This result can be explained through Le Chatelier's principle.
* Cite web
last = Babrauskas
first = Vytenis
title = Temperatures in flames and fires
work = Fire Science and Technology Inc.
accessdate = 2008-01-27
date = 2006-02-25
url = http://www.doctorfire.com/flametmp.html
* [http://web.mit.edu/16.unified/www/SPRING/propulsion/notes/node111.html Adiabatic Flame Temperature]
* Cite web
title = Adiabatic Flame Temperature
work = The Engineering Toolbox
accessdate = 2008-01-27
url = http://www.engineeringtoolbox.com/adiabatic-flame-temperature-d_996.html adiabatic flame temperature of hydrogen, methane, propane and octane with oxygen or air as oxidizers
* Cite web
title = Flame Temperatures for some Common Gases
work = The Engineering Toolbox
accessdate = 2008-01-27
url = http://www.engineeringtoolbox.com/flame-temperatures-gases-d_422.html
* [http://hypertextbook.com/facts/1998/JamesDanyluk.shtml Temperature of a blue flame and common materials]
* [http://www.depcik.com/eduprograms/aftp.htm Adiabatic flame temperature program]
* [http://www.gaseq.co.uk Gaseq] , program for performing chemical equilibrium calculations.
* [http://astronautics.usc.edu/utility/flame_temperature/ Flame Temperature Calculator] - Constant pressure bipropellant adiabatic combustion
* [http://www.engr.colostate.edu/~allan/thermo/page12/adia_flame/Flamemain.html Adiabatic Flame Temperature calculator]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Adiabatic process — This article covers adiabatic processes in thermodynamics. For adiabatic processes in quantum mechanics, see adiabatic process (quantum mechanics). For atmospheric adiabatic processes, see lapse rate. In thermodynamics, an adiabatic process or an … Wikipedia
Flame speed — The flame speed is the measured rate of expansion of the flame front in a combustion reaction. Whereas flame speed is generally used for a fuel, a related term is explosive velocity, which is the same relationship measured for an explosive.… … Wikipedia
Orders of magnitude (temperature) — Temperature in °C compared to the thermodynamic scale in electron volts, which are also used as a unit of temperature. List of orders of magnitude for temperature Factor Multiple Item 10−∞ 0 K … Wikipedia
Адиабатическое горение — экзотермическая химическая реакция, происходящая при постоянном давлении или объеме, при которой исключена потеря энергии в окружающую среду. Температура адиабатического горения при постоянном давлении ниже температуры горения при постоянном… … Википедия
Combustion — This article is about the process of burning. For combustion without external ignition, see spontaneous combustion. For the engine used in mobile propulsion, see internal combustion engine. For the visible part of a fire, see flame. Burning… … Wikipedia
Oxyhydrogen — Knallgas redirects here. For bacteria which oxidize hydrogen, see Knallgas bacteria. Nineteenth century electrolytic cell for producing oxyhydrogen. Oxyhydrogen is a mixture of hydrogen (H2) and oxygen (O2) gases, typically in a 2:1 molar ratio,… … Wikipedia
Diesel cycle — Thermodynamics … Wikipedia
Internal combustion engine — The internal combustion engine is an engine in which the combustion of a fuel (normally a fossil fuel) occurs with an oxidizer (usually air) in a combustion chamber. In an internal combustion engine, the expansion of the high temperature and high … Wikipedia
Nitromethane — IUPAC name … Wikipedia
Exhaust gas recirculation — (EGR) is a nitrogen oxide (NOx) emissions reduction technique used in most gasoline and diesel engines.EGR works by recirculating a portion of an engine s exhaust gas back to the engine cylinders. Intermixing the incoming air with recirculated… … Wikipedia