Pattern welding


Pattern welding

Pattern welding is the practice in sword and knife making of forming a blade of several metal pieces of differing composition that are forge-welded together and twisted and manipulated to form a pattern. Often incorrectly called Damascus steel (which is produced by a different process), blades forged in this manner often display bands of slightly different coloration along their entire length. These bands can be brought out for cosmetic purposes by proper polishing or acid etching. Originally, pattern welding was used to combine steels of different carbon contents, providing the desired mix of hardness and toughness needed for highly demanding tasks such as cutting through armour. Although modern steelmaking processes negate the need to blend different steels, pattern welded steel is still used by custom knifemakers for the cosmetic effects it produces.

History

Pattern welding was developed in both Europe and Asia as a means of averaging the properties of iron and steel. Iron is too soft and flexible for use in weaponry, while the hypereutectoid steel produced in the ancient world was too hard and brittle. The earliest known use of pattern welding in Europe is from an 8th century BC sword found at Singen, Württemberg in Germany (Salter & Ehrenreich 1984). The Celts originally employed alternating rods of iron and steel twisted together and then welded with the use of the bloomery furnace which can bring iron and steel (carburized iron) to a welding temperature, but not melt them. In Asia, the carbon content of the iron and steel produced in the bloomery process was highly variable, and repeated folding and welding was employed to remove excess slag and impurities from the metal and to homogenize it. Two or more batches of fairly uniform steel (each batch with a different composition) were then welded together. The different steels result in blades with improved mechanical properties and a distinctive wavy pattern being observed after etching. The technique first appeared about 300 BCE, and by 500 CE/AD was being used by the Merovingian dynasty. Through their successors, the Carolingian dynasty, the technique became common throughout Europe by about 700 CE/AD. The period of European pattern welding, then, encompasses the Celto-Roman Iron Age through the Migration Era. Introduction of the blast furnace brought it to an end.

By the 9th century in Europe, the blast furnace became available and with it the ability to create homogenous high carbon steel. The need for pattern welding all but died out for other than cosmetic applications. During subsequent centuries the technique was slowly lost, and by 1300 there are few examples of its use. The technique survived, however, in Scandinavia, where good quality iron ores and charcoal were widely available.

It was during this same period that Damascus steel was being produced in the Middle East, and similarities in the markings led many to believe it was the same process being used. Swords made by pattern welding are sometimes said to be "Damascus blades", although the manufacture of Damascus steel is entirely different. The terms "Damascus", "Damask", "damascening", etc. are complete misnomers that have nothing at all to do with European pattern welding technology.

Pattern welding again fell from use in Europe during the 18th century, when English metalsmiths discovered the puddling furnace, and then rediscovered the Indian crucible-fired steels (wootz steel) which were far superior to any mechanical methods. By the 19th century pattern welding had largely disappeared, although today it is used in custom knife making.

The technique is more commonly associated with Japan and reached a high degree of development in the 14th century. This association leads some to incorrectly believe that pattern welding originated in Japan. There are also examples of pattern welding in weaponry from the pre-colonial Philippines.

Techniques

The term "pattern welding" is applied to a broad range of techniques which pursue different goals. Most modern pattern welded steel is done for purely cosmetic reasons using different types of high carbon steel or tool steel, both of which are well suited for the given purpose. Ancient techniques were more focused on blending certain qualities of the steels used to obtain better characteristics than was possible by only using one type of steel.

Altering carbon content

Steel made with the bloomery process, used throughout much of the ancient world, was of very poor quality for making knives and swords. The bloom itself consisted of cast iron, a very brittle form of steel containing over 2% carbon by weight. The bloom is also porous, and filled with pockets of slag. As the slag is worked out during forging, the carbon is also burned from the steel, producing in the end wrought iron, with a very low carbon content. To achieve the desired carbon content for a blade (generally around 0.7 to 1.0%) carbon must be added back into the wrought iron, generally by means of carburization. Since carburization only penetrates the surface of the iron (providing, in essence, only case hardening) the thin veneer must be mixed back into the interior to form the desired high carbon steel. This is usually done by either stacking or flattening and folding the carburized bars. This creates the characteristic thin layers seen in pattern welded steel. Additional shapes can be made by differing how the bars were stacked or folded. Viking swords were often made with twisted bars, producing spiral patterns, and today many knifemakers use steel cable to produce complex, spiral-in-spiral patterns.

Conservation of high carbon steel

Since producing high carbon steel from wrought iron was very difficult, pattern welding also served to conserve this difficult to make steel by using it only for the parts of the blades where it was needed. Many swords were made with the minimum possible amount of high carbon steel along the cutting edge, with the rest of the blade being made of low carbon steel or wrought iron. A thin strip of high carbon steel could be laminated between two layers of softer steel, or a core of soft steel could be wrapped in high carbon steel. The Japanese katana was often found with complex patterns of soft and hard steels; having 5 sections of differing hardness welded together to form the final blade was not uncommon. The end result would be a blade with a very high carbon edge (as much as 1.0%, equal to the highest carbon content found in low alloy steels in use today) and a softer spine. The very hard, but brittle, edge made the swords extremely sharp, while the spine gave the blade flexibility, so that it would bend rather than break. The problem with the laminate design was that if the brittle edge steel chipped down to the soft core (a near certainty if swords were brought into edge to edge contact), the sword was ruined; grinding out the chip would expose the soft core and result in an unsharpenable blade. Correct technique for these blades was to parry with the softer, stronger sides or back of the blade, to protect the more fragile cutting edge.

A similar technique was also employed by Scandinavian Medieval swordsmiths. The Mora knife is today manufactured with a similar technique. Today the traditional crucible steel is seldom used, but the high carbon steel is usually tool steel or stainless steel.

Decorative finish

The ancient swordmakers also exploited the aesthetic qualities of pattern welded steel. The Vikings in particular were fond of twisting bars of steel around each other, welding the bars together by hammering and then repeating the process with the resulting bars, to create complex patterns in the final steel bar. Two bars twisted in opposite directions created the common chevron pattern. Often, the centre of the blade was a core of soft steel, and the edges were solid high carbon steel, similar to the laminates of the Japanese.

While "cable Damascus", forged from high carbon multi-strand cable, is a popular item for bladesmiths to produce, some modern bladesmiths have taken pattern welding to new heights. The American Bladesmith Society's Master Smith test, for example, requires a 300 layer blade to be forged. Large numbers of layers are generally produced by folding, where a small number of layers are welded together, then the blank is cut in half, stacked, and welded again, with each operation doubling the number of layers. Starting with just two layers, eight folding operations will yield 512 layers in the blank. A blade ground from such a blank will show a grain much like an object cut from a block of wood. A layered billet of steel rods with the blade blank cut perpendicular to the layers can also produce some spectacular patterns, including mosaics or even writing. Different treatments of the steel after it is ground and polished, such as bluing, etching, or treatments with various other chemicals that react differently to the different steels used can create bright, high-contrast finishes on the steel. Some master smiths go as far as to use an electrical discharge machining mill to cut interlocking patterns out of different steels, fit them together, then weld the resulting assembly into a solid block of steel.

See also

* Wootz steel, an Indian crucible steel
* Bulat steel, a Russian crucible steel
* Mokume-gane, a similar technique, often involving precious metals, used to produce decorative pieces

References

*Ian Peirce, Ewart Oakeshott (Introduction), "Swords of the Viking Age", 2004, ISBN 0-85115-914-1

External links

* [http://fenrisforge.com/How%20to%20make%20Damascus.htm How to make pattern welded blades]
* [http://www.cashenblades.com/Info/Pattern%20welding.html Bladesmith Kevin Cashen's page on pattern welding]
* [http://www.staff.hum.ku.dk/dbwagner/REHD/REHD.html Ancient carburisation of iron to steel: a comment]
* [http://www.jordanknives.com/patternwelding.htm Master bladesmith Andrew Jordan's page on pattern welding]
* [http://www.caffreyknives.net/bsteel.htm ABS Mastersmith Ed Caffery's Mosaic Damascus pattern welded steel]
* [http://www.dfoggknives.com/copy_of_index/damascus.htm Pictures forged into pattern welded steel (shows how EDM mosaic technique works)]
* [http://www.vikingsword.com/virtmus.html Mediæval Sword Virtual Museum] , which contains close-up images of Viking swords, showing the pattern welding structures.


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Welding — is a fabrication process that joins materials, usually metals or thermoplastics, by causing coalescence. This is often done by melting the workpieces and adding a filler material to form a pool of molten material (the weld puddle ) that cools to… …   Wikipedia

  • Forge welding — is a welding process of heating two or more pieces of metal and then hammering them together. The process is one of the simplest methods of joining metals and has been used since ancient times. Forge welding is versatile, being able to join a… …   Wikipedia

  • Gas metal arc welding — RMD redirects here. RMD may also refer to IRA Required Minimum Distributions. Gas metal arc welding …   Wikipedia

  • Arc welding — uses a welding power supply to create an electric arc between an electrode and the base material to melt the metals at the welding point. They can use either direct (DC) or alternating (AC) current, and consumable or non consumable electrodes.… …   Wikipedia

  • Damascus steel — For Damascus Twist barrels, see Skelp. For the album of the same name, see Damascus Steel (album). Close up of a 16th century Iranian crucible forged Damascus steel sword Damascus steel was a term used by several Western cultures from the… …   Wikipedia

  • Sword — For other uses, see Sword (disambiguation) and Swords (disambiguation). Swiss longsword, 15th or 16th century A sword is a bladed weapon (edged weapon) used primarily for cutting or thrusting. The precise definition of the term varies with the… …   Wikipedia

  • Bladesmith — Bladesmithing is the art of blacksmithing that relates specifically to creating knives, swords, daggers and other blades using a forge, hammer, anvil, and other smithing tools. Bladesmiths employ a variety of metalworking techniques used by… …   Wikipedia

  • Blacksmith — For other uses, see Blacksmith (disambiguation). Blacksmith A blacksmith at work Occupation …   Wikipedia

  • Tool and die maker — Not to be confused with tap and die. Tool and die makers are workers in the manufacturing industry who make jigs, fixtures, dies, molds, machine tools, cutting tools (such as milling cutters and form tools), gauges, and other tools used in… …   Wikipedia

  • Katana construction — was the labour intensive bladesmithing process developed in Japan for forging katana and other Japanese blades. Katana and wakizashi were often forged with different profiles, different blade thicknesses, and varying amounts of grind. Wakizashi… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.