The Atterberg limits are a basic measure of the nature of a fine-grained
soil. Depending on the water contentof the soil, it may appear in four states: solid, semi-solid, plastic and liquid. In each state the consistency and behavior of a soil is different and thus so are its engineering properties. Thus, the boundary between each state can be defined based on a change in the soil's behavior. The Atterberg limits can be used to distinguish between siltand clay, and it can distinguish between different types of silts and clays. These limits were created by Albert Atterberg, a Swedish chemist. cite web | title=Brief history of Swedish Soil Mechanics | url=http://www.geoforum.com/info/pileinfo/swedsoilmech.asp | accessdate=2007-01-15 ] They were later refined by Arthur Casagrande.
The shrinkage limit (SL) is the water content where further loss of moisture will not result in any more volume reduction. [ cite web |url=http://www.usace.army.mil/publications////eng-manuals/em1110-2-1906/a-IIIB.pdf |title=Shrinkage Limit Test |work=
United States Army Corps of Engineers] The test to determine the shrinkage limit is ASTM InternationalD427. The shrinkage limit is much less commonly used than the liquid limit and the plastic limit.
The plastic limit (PL) is the water content where soil starts to exhibit plastic behavior. A thread of soil is at its plastic limit when it is rolled to a diameter of 3 mm and crumbles. To improve consistency, a 3 mm diameter rod is often used to gauge the thickness of the thread when conducting the test.
The liquid limit (LL) is the water content where a soil changes from liquid to plastic behavior. The original liquid limit test of Atterberg's involved mixing a pat of clay in a little round-bottomed porcelain bowl of 10-12cm diameter. A groove was cut through the pat of clay with a spatula, and the bowl was then struck many times against the palm of one hand.
Casagrande subsequently standardized the apparatus and the procedures to make the measurement more repeatable. Soil is placed into the metal cup portion of the device and a groove is made down its center with a standardized tool. The cup is repeatedly dropped 10mm onto a hard rubber base until the groove is closed for 13 mm (½ inch). The moisture content at which it takes 25 drops of the cup to cause the groove to close is defined as the liquid limit.
Another method for measuring the liquid limit is the
Cone Penetrometertest. It is based on the measurement of penetration into the soil of a standardized cone of specific mass. Despite the universal prevalence of the Casagrande method, the cone penetrometer is often considered to be a more consistent alternative because it minimizes the possibility of human variations when carrying out the test.
The values of these limits are used in a number of ways. There is also a close relationship between the limits and properties of a soil such as compressibility, permeability, and strength. This is thought to be very useful because as limit determination is relatively simple, it is more difficult to determine these other properties. Thus the Atterberg limits are not only used to identify the soil's classification, but it also allows for the use of empirical correlations for some other engineering properties.
The plasticity index (PI) is a measure of the plasticity of a soil. The plasticity index is the size of the range of water contents where the soil exhibits plastic properties. The PI is the difference between the liquid limit and the plastic limit (PI = LL-PL). Soils with a high PI tend to be clay, those with a lower PI tend to be silt, and those with a PI of 0 tend to have little or no silt or clay.
The liquidity index (LI) is used for scaling the natural water content of a soil sample to the limits. It can be calculated as a ratio of difference between natural water content, plastic limit, and plasticity index: LI=(W-PL)/(LL-PL) where W is the natural water content.
The activity (A) of a soil is the PI divided by the percent of clay-sized particles present. Different types of clays have different specific surface areas which controls how much wetting is required to move a soil from one phase to another such as across the liquid limit or the plastic limit. From the activity one can predict the dominant clay type present in a soil sample. High activity signifies large volume change when wetted and large shrinkage when dried. Soil with high activity are very reactive chemically.
Normally, activity of clay is between 0.75 and 1.25. It is assumed that the plasticity index is approximately equal to the clay fraction (A = 1). When A is less than 0.75, it is considered inactive. When it is greater than 1.25, it is considered active.
* [http://www.ce.washington.edu/~geotech/courses/cee366/arduino/exercise3.PDF University of Washington lecture notes]
* [http://jan.ucc.nau.edu/~doetqp-p/courses/env320/lec7/Lec7.html Soil Physical Properties--Mechanics]
Wikimedia Foundation. 2010.
Look at other dictionaries:
Albert Atterberg — Albert Mauritz Atterberg (March 19 1846–April 4 1916) was a Swedish chemist and agricultural scientist who created the Atterberg limits that are commonly referred to by geotechnical engineers and engineering geologists today.Atterberg received… … Wikipedia
Geotechnical investigation — Geotechnical investigations are performed by geotechnical engineers or engineering geologists to obtain information on the physical properties of soil and rock around a site to design earthworks and foundations for proposed structures and for… … Wikipedia
Geotechnical engineering — [ Boston s Big Dig presented geotechnical challenges in an urban environment.] Geotechnical engineering is the branch of civil engineering concerned with the engineering behavior of earth materials. Geotechnical engineering includes investigating … Wikipedia
Clay — For other uses, see Clay (disambiguation). The Gay Head cliffs in Martha s Vineyard consist almost entirely of clay. Clay is a general term including many combinations of one or more clay minerals with traces of metal oxides and organic… … Wikipedia
Cone Penetrometer — The Cone Penetrometer apparatus is an alternative method to the Casagrande Device in measuring the Liquid Limit of a soil sample (See:Atterberg Limits). It is usually considered to be a more scientific approach because it is based less upon human … Wikipedia
Sand — For other uses, see Sand (disambiguation). Close up of sand from the Gobi Desert, Mongolia, showing a surface area of 1 square centimetres … Wikipedia
Newmark's sliding block — The Newmark s sliding block analysis method is an engineering method used to calculate the permanent displacements of soil slopes (also embankments and dams) during seismic loading. It is also simply called Newmark s analysis or Sliding block… … Wikipedia
Earthquake — For other uses, see Earthquake (disambiguation). Global earthquake epicenters, 1963–1998 … Wikipedia
Plasticity — generally means ability to permanently change or deform. (It differs from elasticity , which refers to ability to change temporarily and revert back to original form.)More specific meanings include:In the sciences* Plasticity (physics): In… … Wikipedia
Landslide — This article is about the geological phenomenon. For other uses, see Landslide (disambiguation). Rockslide redirects here. For the comic book character, see Rockslide (comics). Computer simulation of a slump landslide in San Mateo County,… … Wikipedia