# Nuclear fusion

﻿
Nuclear fusion

Nuclear fusion is the process by which two or more atomic nuclei join together, or "fuse", to form a single heavier nucleus. This is usually accompanied by the release or absorption of large quantities of energy. Fusion is the process that powers active stars, the hydrogen bomb and experimental devices examining fusion power for electrical generation.

The fusion of two nuclei with lower masses than iron (which, along with nickel, has the largest binding energy per nucleon) generally releases energy, while the fusion of nuclei heavier than iron absorbs energy. The opposite is true for the reverse process, nuclear fission. This means that fusion generally occurs for lighter elements only, and likewise, that fission normally occurs only for heavier elements. There are extreme astrophysical events that can lead to short periods of fusion with heavier nuclei. This is the process that gives rise to nucleosynthesis, the creation of the heavy elements during events like supernovas.

Creating the required conditions for fusion on Earth is very difficult, to the point that it has not been accomplished at any scale for protium, the common light isotope of hydrogen that undergoes natural fusion in stars. In nuclear weapons, some of the energy released by an atomic bomb is used to compress and heat a fusion fuel containing heavier isotopes of hydrogen, and also sometimes lithium, to the point of "ignition". At this point, the energy released in the fusion reactions is enough to briefly maintain the reaction. Fusion-based nuclear power experiments attempt to create similar conditions using less dramatic means, although to date these experiments have failed to maintain conditions needed for ignition long enough for fusion to be a viable commercial power source.

Building upon the nuclear transmutation experiments by Ernest Rutherford, carried out several years earlier, the laboratory fusion of heavy hydrogen isotopes was first accomplished by Mark Oliphant in 1932. During the remainder of that decade the steps of the main cycle of nuclear fusion in stars were worked out by Hans Bethe. Research into fusion for military purposes began in the early 1940s as part of the Manhattan Project, but this was not accomplished until 1951 (see the Greenhouse Item nuclear test), and nuclear fusion on a large scale in an explosion was first carried out on November 1, 1952, in the Ivy Mike hydrogen bomb test.

Research into developing controlled thermonuclear fusion for civil purposes also began in earnest in the 1950s, and it continues to this day. Two projects, the National Ignition Facility and ITER are in the process of reaching breakeven after 60 years of design improvements developed from previous experiments.

## Overview

Fusion of deuterium with tritium creating helium-4, freeing a neutron, and releasing 17.59 MeV of energy, as an appropriate amount of mass changing forms to appear as the kinetic energy of the products, in agreement with kinetic E = Δmc2, where Δm is the change in rest mass of particles.[1]

Fusion reactions power the stars and produce virtually all elements in a process called nucleosynthesis.

Generally, when dealing with elements lighter than iron, the lower the ratio of atomic mass to mass number is, the heavier the nucleus is. This is known as mass defect. Fusion of lighter nuclei into heavier nuclei leads to loss of mass when the energy of binding is removed (this energy carries away the lost mass), even though no nucleons are lost. This lost mass is present in the released energy in accordance with E=mc2. Most of the excess binding energy is released as kinetic energy of the resulting particles. When these particles are slowed, such as in collisions with one another, this energy is available to do work or be converted to electromagnetic radiation or heat.

The fusion of lighter elements in stars releases energy (and the mass that always accompanies it). For example, in the fusion of four hydrogen nuclei to form helium, seven-tenths of 1 percent of the mass is carried away from the system in the form of kinetic energy or other forms of energy (such as electromagnetic radiation).[2] However, the production of elements heavier than iron absorbs energy.

Research into controlled fusion, with the aim of producing fusion power for the production of electricity, has been conducted for over 60 years. It has been accompanied by extreme scientific and technological difficulties, but has resulted in progress. At present, controlled fusion reactions have been unable to produce break-even (self-sustaining) controlled fusion reactions.[3] Workable designs for a reactor that theoretically will deliver ten times more fusion energy than the amount needed to heat up plasma to required temperatures (see ITER) were originally scheduled to be operational in 2018, however this has been delayed and a new date has not been stated.

It takes considerable energy to force nuclei to fuse, even those of the lightest element, hydrogen. This is because all nuclei have a positive charge (due to their protons), and as like charges repel, nuclei strongly resist being put too close together. Accelerated to high speeds (that is, heated to thermonuclear temperatures), they can overcome this electrostatic repulsion and get close enough for the attractive nuclear force to be sufficiently strong to achieve fusion. The fusion of lighter nuclei, which creates a heavier nucleus and often a free neutron or proton, generally releases more energy than it takes to force the nuclei together; this is an exothermic process that can produce self-sustaining reactions. The National Ignition Facility, which uses laser-driven inertial confinement fusion, is thought to be capable of break-even fusion.

The first large-scale laser target experiments were performed in June 2009 and ignition experiments are beginning early in 2011.[4][5]

Energy released in most nuclear reactions is much larger than in chemical reactions, because the binding energy that holds a nucleus together is far greater than the energy that holds electrons to a nucleus. For example, the ionization energy gained by adding an electron to a hydrogen nucleus is 13.6 eV—less than one-millionth of the 17 MeV released in the deuteriumtritium (D–T) reaction shown in the diagram to the right. Fusion reactions have an energy density many times greater than nuclear fission; the reactions produce far greater energies per unit of mass even though individual fission reactions are generally much more energetic than individual fusion ones, which are themselves millions of times more energetic than chemical reactions. Only direct conversion of mass into energy, such as that caused by the annihilatory collision of matter and antimatter, is more energetic per unit of mass than nuclear fusion.

## Requirements

A substantial energy barrier of electrostatic forces must be overcome before fusion can occur. At large distances two naked nuclei repel one another because of the repulsive electrostatic force between their positively charged protons. If two nuclei can be brought close enough together, however, the electrostatic repulsion can be overcome by the attractive nuclear force, which is stronger at close distances.

When a nucleon such as a proton or neutron is added to a nucleus, the nuclear force attracts it to other nucleons, but primarily to its immediate neighbours due to the short range of the force. The nucleons in the interior of a nucleus have more neighboring nucleons than those on the surface. Since smaller nuclei have a larger surface area-to-volume ratio, the binding energy per nucleon due to the nuclear force generally increases with the size of the nucleus but approaches a limiting value corresponding to that of a nucleus with a diameter of about four nucleons. It is important to keep in mind that the above picture is a toy model because nucleons are quantum objects, and so, for example, since two neutrons in a nucleus are identical to each other, distinguishing one from the other, such as which one is in the interior and which is on the surface, is in fact meaningless, and the inclusion of quantum mechanics is necessary for proper calculations.

The electrostatic force, on the other hand, is an inverse-square force, so a proton added to a nucleus will feel an electrostatic repulsion from all the other protons in the nucleus. The electrostatic energy per nucleon due to the electrostatic force thus increases without limit as nuclei get larger.

At short distances the attractive nuclear force is stronger than the repulsive electrostatic force. Therefore, the main technical difficulty for fusion is getting the nuclei close enough to fuse.

The net result of these opposing forces is that the binding energy per nucleon generally increases with increasing size, up to the elements iron and nickel, and then decreases for heavier nuclei. Eventually, the binding energy becomes negative and very heavy nuclei (all with more than 208 nucleons, corresponding to a diameter of about 6 nucleons) are not stable. The four most tightly bound nuclei, in decreasing order of binding energy per nucleon, are 62
Ni
, 58
Fe
, 56
Fe
, and 60
Ni
.[6] Even though the nickel isotope, 62
Ni
, is more stable, the iron isotope 56
Fe
is an order of magnitude more common. This is due to a greater disintegration rate for 62
Ni
in the interior of stars driven by photon absorption.

A notable exception to this general trend is the helium-4 nucleus, whose binding energy is higher than that of lithium, the next heaviest element. The Pauli exclusion principle provides an explanation for this exceptional behavior—it says that because protons and neutrons are fermions, they cannot exist in exactly the same state. Each proton or neutron energy state in a nucleus can accommodate both a spin up particle and a spin down particle. Helium-4 has an anomalously large binding energy because its nucleus consists of two protons and two neutrons; so all four of its nucleons can be in the ground state. Any additional nucleons would have to go into higher energy states.

The situation is similar if two nuclei are brought together. As they approach each other, all the protons in one nucleus repel all the protons in the other. Not until the two nuclei actually come in contact can the strong nuclear force take over. Consequently, even when the final energy state is lower, there is a large energy barrier that must first be overcome. It is called the Coulomb barrier.

The Coulomb barrier is smallest for isotopes of hydrogen, as their nuclei contain only a single positive charge. A diproton is not stable, so neutrons must also be involved, ideally in such a way that a helium nucleus, with its extremely tight binding, is one of the products.

Using deuterium-tritium fuel, the resulting energy barrier is about 0.1 MeV.[citation needed] In comparison, the energy needed to remove an electron from hydrogen is 13.6 eV, about 750 times less energy. The (intermediate) result of the fusion is an unstable 5He nucleus, which immediately ejects a neutron with 14.1 MeV.[citation needed] The recoil energy of the remaining 4He nucleus is 3.5 MeV,[citation needed] so the total energy liberated is 17.6 MeV.[citation needed] This is many times more than what was needed to overcome the energy barrier.

If the energy to initiate the reaction comes from accelerating one of the nuclei, the process is called beam-target fusion; if both nuclei are accelerated, it is beam-beam fusion. If the nuclei are part of a plasma near thermal equilibrium, the process is called thermonuclear fusion. Temperature is a measure of the average kinetic energy of particles, so by heating the nuclei they will gain energy and eventually have enough to overcome this 0.1 MeV. Converting the units between electronvolts and kelvin shows that the barrier would be overcome at a temperature in excess of 120 million kelvins.

There are two effects that lower the actual temperature needed. One is the fact that temperature is the average kinetic energy, implying that some nuclei at this temperature would actually have much higher energy than 0.1 MeV, while others would be much lower. It is the nuclei in the high-energy tail of the velocity distribution that account for most of the fusion reactions. The other effect is quantum tunneling. The nuclei do not actually have to have enough energy to overcome the Coulomb barrier completely. If they have nearly enough energy, they can tunnel through the remaining barrier. For these reasons fuel at lower temperatures will still undergo fusion events, at a lower rate.

The fusion reaction rate increases rapidly with temperature until it maximizes and then gradually drops off. The DT rate peaks at a lower temperature (about 70 keV, or 800 million kelvin) and at a higher value than other reactions commonly considered for fusion energy.

The reaction cross section σ is a measure of the probability of a fusion reaction as a function of the relative velocity of the two reactant nuclei. If the reactants have a distribution of velocities, e.g. a thermal distribution with thermonuclear fusion, then it is useful to perform an average over the distributions of the product of cross section and velocity. The reaction rate (fusions per volume per time) is <σv> times the product of the reactant number densities:

$f = n_1 n_2 \langle \sigma v \rangle.$

If a species of nuclei is reacting with itself, such as the DD reaction, then the product n1n2 must be replaced by (1 / 2)n2.

$\langle \sigma v \rangle$ increases from virtually zero at room temperatures up to meaningful magnitudes at temperatures of 10–100 keV. At these temperatures, well above typical ionization energies (13.6 eV in the hydrogen case), the fusion reactants exist in a plasma state.

The significance of $\langle \sigma v \rangle$ as a function of temperature in a device with a particular energy confinement time is found by considering the Lawson criterion.

### Gravitational confinement

One force capable of confining the fuel well enough to satisfy the Lawson criterion is gravity. The mass needed, however, is so great that gravitational confinement is only found in stars–the least massive stars capable of sustained fusion are red dwarfs, while brown dwarfs are able to fuse deuterium and lithium if they are of sufficient mass. In stars heavy enough, after the supply of hydrogen is exhausted in their cores, their cores (or a shell around the core) start fusing helium to carbon. In the most massive stars (at least 8–11 solar masses), the process is continued until some of their energy is produced by fusing lighter elements to iron. As iron has one of the highest binding energies, reactions producing heavier elements are generally endothermic. Therefore significant amounts of heavier elements are not formed during stable periods of massive star evolution, but are formed in supernova explosions. Some lighter stars also form these elements in the outer parts of the stars over long periods of time, by absorbing energy from fusion in the inside of the star, by absorbing neutrons that are emitted from the fusion process.

All of the elements heavier than iron have some potential energy to release, in theory. At the extremely heavy end of element production, these heavier elements can produce energy in the process of being split again back toward the size of iron, in the process of nuclear fission. Nuclear fission thus releases energy which has been stored, sometimes billions of years before, during stellar nucleosynthesis.

### Magnetic confinement

Electrically charged particles (such as fuel ions) will follow magnetic field lines (see Guiding center). The fusion fuel can therefore be trapped using a strong magnetic field. A variety of magnetic configurations exist, including the toroidal geometries of tokamaks and stellarators and open-ended mirror confinement systems.

### Inertial confinement

A third confinement principle is to apply a rapid pulse of energy to a large part of the surface of a pellet of fusion fuel, causing it to simultaneously "implode" and heat to very high pressure and temperature. If the fuel is dense enough and hot enough, the fusion reaction rate will be high enough to burn a significant fraction of the fuel before it has dissipated. To achieve these extreme conditions, the initially cold fuel must be explosively compressed. Inertial confinement is used in the hydrogen bomb, where the driver is x-rays created by a fission bomb. Inertial confinement is also attempted in "controlled" nuclear fusion, where the driver is a laser, ion, or electron beam, or a Z-pinch. Another method is to use conventional high explosive material to compress a fuel to fusion conditions.[7][8] The UTIAS explosive-driven-implosion facility was used to produce stable, centered and focused hemispherical implosions[9] to generate neutrons from D-D reactions. The simplest and most direct method proved to be in a predetonated stoichiometric mixture of deuterium-oxygen. The other successful method was using a miniature Voitenko compressor,[10] where a plane diaphragm was driven by the implosion wave into a secondary small spherical cavity that contained pure deuterium gas at one atmosphere.[11]

Some other confinement principles have been investigated, such as muon-catalyzed fusion, the Farnsworth–Hirsch fusor and Polywell (inertial electrostatic confinement), and bubble fusion.

### Production methods

A variety of methods are known to effect nuclear fusion. Some are "cold" in the strict sense that no part of the material is hot (except for the reaction products), some are "cold" in the limited sense that the bulk of the material is at a relatively low temperature and pressure but the reactants are not, and some are "hot" fusion methods that create macroscopic regions of very high temperature and pressure.

#### Muon-catalyzed fusion

Muon-catalyzed fusion is a well-established and reproducible fusion process that occurs at ordinary temperatures. It was studied in detail by Steven Jones in the early 1980s. It has not been reported to produce net energy. Net energy production from this reaction cannot occur because of the energy required to create muons, their 2.2 µs half-life, and the chance that a muon will bind to the new alpha particle and thus stop catalyzing fusion.[12]

#### Generally cold, locally hot fusion

Accelerator-based light-ion fusion is a technique using particle accelerators to achieve particle kinetic energies sufficient to induce light-ion fusion reactions. Accelerating light ions is relatively easy, and can be done in an efficient manner—all it takes is a vacuum tube, a pair of electrodes, and a high-voltage transformer; fusion can be observed with as little as 10 kV between electrodes. The key problem with accelerator-based fusion (and with cold targets in general) is that fusion cross sections are many orders of magnitude lower than Coulomb interaction cross sections. Therefore the vast majority of ions end up expending their energy on bremsstrahlung and ionization of atoms of the target. Devices referred to as sealed-tube neutron generators are particularly relevant to this discussion. These small devices are miniature particle accelerators filled with deuterium and tritium gas in an arrangement that allows ions of these nuclei to be accelerated against hydride targets, also containing deuterium and tritium, where fusion takes place. Hundreds of neutron generators are produced annually for use in the petroleum industry where they are used in measurement equipment for locating and mapping oil reserves. Despite periodic reports in the popular press by scientists claiming to have invented "table-top" fusion machines, neutron generators have been around for half a century. The sizes of these devices vary but the smallest instruments are often packaged in sizes smaller than a loaf of bread. These devices do not produce a net power output.

Sonofusion or bubble fusion, a controversial variation on the sonoluminescence theme, suggests that acoustic shock waves, creating temporary bubbles (cavitation) that expand and collapse shortly after creation, can produce temperatures and pressures sufficient for nuclear fusion.[13]

The Farnsworth–Hirsch fusor is a tabletop device in which fusion occurs. This fusion comes from high effective temperatures produced by electrostatic acceleration of ions. The device can be built inexpensively, but it too is unable to produce a net power output.

The Polywell is a non-thermodynamic equilibrium machine that uses electrostatic confinement to accelerate ions into a center where they fuse together.

Antimatter-initialized fusion uses small amounts of antimatter to trigger a tiny fusion explosion. This has been studied primarily in the context of making nuclear pulse propulsion, and pure fusion bombs feasible. This is not near becoming a practical power source, due to the cost of manufacturing antimatter alone.

Pyroelectric fusion was reported in April 2005 by a team at UCLA. The scientists used a pyroelectric crystal heated from −34 to 7 °C (−29 to 45 °F), combined with a tungsten needle to produce an electric field of about 25 gigavolts per meter to ionize and accelerate deuterium nuclei into an erbium deuteride target. Though the energy of the deuterium ions generated by the crystal has not been directly measured, the authors used 100 keV (a temperature of about 109 K) as an estimate in their modeling.[14] At these energy levels, two deuterium nuclei can fuse together to produce a helium-3 nucleus, a 2.45 MeV neutron and bremsstrahlung. Although it makes a useful neutron generator, the apparatus is not intended for power generation since it requires far more energy than it produces.[15][16][17][18]

#### Hot fusion

In hot fusion, the fuel reaches tremendous temperature and pressure inside a fusion reactor or star.

The methods in the second group are examples of non-equilibrium systems, in which very high temperatures and pressures are produced in a relatively small region adjacent to material of much lower temperature. In his doctoral thesis for MIT, Todd Rider did a theoretical study of all quasineutral, isotropic, non-equilibrium fusion systems. He demonstrated that all such systems will leak energy at a rapid rate due to bremsstrahlung produced when electrons in the plasma hit other electrons or ions at a cooler temperature and suddenly decelerate[citation needed]. The problem is not as pronounced in a hot plasma because the range of temperatures, and thus the magnitude of the deceleration, is much lower. Note that Rider's work does not apply to non-neutral and/or anisotropic non-equilibrium plasmas.

## Important reactions

### Astrophysical reaction chains

The proton-proton chain dominates in stars the size of the Sun or smaller.
The CNO cycle dominates in stars heavier than the Sun.

The most important fusion process in nature is the one that powers stars. The net result is the fusion of four protons into one alpha particle, with the release of two positrons, two neutrinos (which changes two of the protons into neutrons), and energy, but several individual reactions are involved, depending on the mass of the star. For stars the size of the sun or smaller, the proton-proton chain dominates. In heavier stars, the CNO cycle is more important. Both types of processes are responsible for the creation of new elements as part of stellar nucleosynthesis.

At the temperatures and densities in stellar cores the rates of fusion reactions are notoriously slow. For example, at solar core temperature (T ≈ 15 MK) and density (160 g/cm3), the energy release rate is only 276 μW/cm3—about a quarter of the volumetric rate at which a resting human body generates heat.[19] Thus, reproduction of stellar core conditions in a lab for nuclear fusion power production is completely impractical. Because nuclear reaction rates strongly depend on temperature (exp(−E/kT)), achieving reasonable energy production rates in terrestrial fusion reactors requires 10–100 times higher temperatures (compared to stellar interiors): T ≈ 0.1–1.0 GK.

### Criteria and candidates for terrestrial reactions

In man-made fusion, the primary fuel is not constrained to be protons and higher temperatures can be used, so reactions with larger cross-sections are chosen. This implies a lower Lawson criterion, and therefore less startup effort. Another concern is the production of neutrons, which activate the reactor structure radiologically, but also have the advantages of allowing volumetric extraction of the fusion energy and tritium breeding. Reactions that release no neutrons are referred to as aneutronic.

To be a useful energy source, a fusion reaction must satisfy several criteria. It must

• Be exothermic: This may be obvious, but it limits the reactants to the low Z (number of protons) side of the curve of binding energy. It also makes helium 4
He
the most common product because of its extraordinarily tight binding, although 3
He
and 3
H
also show up.
• Involve low Z nuclei: This is because the electrostatic repulsion must be overcome before the nuclei are close enough to fuse.
• Have two reactants: At anything less than stellar densities, three body collisions are too improbable. In inertial confinement, both stellar densities and temperatures are exceeded to compensate for the shortcomings of the third parameter of the Lawson criterion, ICF's very short confinement time.
• Have two or more products: This allows simultaneous conservation of energy and momentum without relying on the electromagnetic force.
• Conserve both protons and neutrons: The cross sections for the weak interaction are too small.

Few reactions meet these criteria. The following are those with the largest cross sections[citation needed]:

 (1) 2 1D + 3 1T → 4 2He ( 3.5 MeV ) + n0 ( 14.1 MeV ) (2i) 2 1D + 2 1D → 3 1T ( 1.01 MeV ) + p+ ( 3.02 MeV ) 50% (2ii) → 3 2He ( 0.82 MeV ) + n0 ( 2.45 MeV ) 50% (3) 2 1D + 3 2He → 4 2He ( 3.6 MeV ) + p+ ( 14.7 MeV ) (4) 3 1T + 3 1T → 4 2He + 2 n0 + 11.3 MeV (5) 3 2He + 3 2He → 4 2He + 2 p+ + 12.9 MeV (6i) 3 2He + 3 1T → 4 2He + p+ + n0 + 12.1 MeV 51% (6ii) → 4 2He ( 4.8 MeV ) + 2 1D ( 9.5 MeV ) 43% (6iii) → 4 2He ( 0.5 MeV ) + n0 ( 1.9 MeV ) + p+ ( 11.9 MeV ) 6% (7i) 2 1D + 6 3Li → 2 4 2He + 22.4 MeV (7ii) → 3 2He + 4 2He + n0 + 2.56 MeV (7iii) → 7 3Li + p+ + 5.0 MeV (7iv) → 7 4Be + n0 + 3.4 MeV (8) p+ + 6 3Li → 4 2He ( 1.7 MeV ) + 3 2He ( 2.3 MeV ) (9) 3 2He + 6 3Li → 2 4 2He + p+ + 16.9 MeV (10) p+ + 11 5B → 3 4 2He + 8.7 MeV
 Nucleosynthesis Related topics Astrophysics Nuclear fusion Nuclear fission edit

For reactions with two products, the energy is divided between them in inverse proportion to their masses, as shown. In most reactions with three products, the distribution of energy varies. For reactions that can result in more than one set of products, the branching ratios are given.

Some reaction candidates can be eliminated at once.[20] The D-6Li reaction has no advantage compared to p+-11
5
B
because it is roughly as difficult to burn but produces substantially more neutrons through 2
1
D
-2
1
D
side reactions. There is also a p+-7
3
Li
reaction, but the cross section is far too low, except possibly when Ti > 1 MeV, but at such high temperatures an endothermic, direct neutron-producing reaction also becomes very significant. Finally there is also a p+-9
4
Be
reaction, which is not only difficult to burn, but 9
4
Be
can be easily induced to split into two alpha particles and a neutron.

In addition to the fusion reactions, the following reactions with neutrons are important in order to "breed" tritium in "dry" fusion bombs and some proposed fusion reactors:

 n0 + 6 3Li → 3 1T + 4 2He n0 + 7 3Li → 3 1T + 4 2He + n0

To evaluate the usefulness of these reactions, in addition to the reactants, the products, and the energy released, one needs to know something about the cross section. Any given fusion device has a maximum plasma pressure it can sustain, and an economical device would always operate near this maximum. Given this pressure, the largest fusion output is obtained when the temperature is chosen so that <σv>/T2 is a maximum. This is also the temperature at which the value of the triple product nTτ required for ignition is a minimum, since that required value is inversely proportional to <σv>/T2 (see Lawson criterion). (A plasma is "ignited" if the fusion reactions produce enough power to maintain the temperature without external heating.) This optimum temperature and the value of <σv>/T2 at that temperature is given for a few of these reactions in the following table.

fuel T [keV] <σv>/T2 [m3/s/keV2]
2
1
D
-3
1
T
13.6 1.24×10−24
2
1
D
-2
1
D
15 1.28×10−26
2
1
D
-3
2
He
58 2.24×10−26
p+-6
3
Li
66 1.46×10−27
p+-11
5
B
123 3.01×10−27

Note that many of the reactions form chains. For instance, a reactor fueled with 3
1
T
and 3
2
He
creates some 2
1
D
, which is then possible to use in the 2
1
D
-3
2
He
reaction if the energies are "right". An elegant idea is to combine the reactions (8) and (9). The 3
2
He
from reaction (8) can react with 6
3
Li
in reaction (9) before completely thermalizing. This produces an energetic proton, which in turn undergoes reaction (8) before thermalizing. Detailed analysis shows that this idea would not work well[citation needed], but it is a good example of a case where the usual assumption of a Maxwellian plasma is not appropriate.

### Neutronicity, confinement requirement, and power density

The only man-made fusion device to achieve ignition to date is the hydrogen bomb. The detonation of the first device, codenamed Ivy Mike, is shown here.

Any of the reactions above can in principle be the basis of fusion power production. In addition to the temperature and cross section discussed above, we must consider the total energy of the fusion products Efus, the energy of the charged fusion products Ech, and the atomic number Z of the non-hydrogenic reactant.

Specification of the 2
1
D
-2
1
D
reaction entails some difficulties, though. To begin with, one must average over the two branches (2) and (3). More difficult is to decide how to treat the 3
1
T
and 3
2
He
products. 3
1
T
burns so well in a deuterium plasma that it is almost impossible to extract from the plasma. The 2
1
D
-3
2
He
reaction is optimized at a much higher temperature, so the burnup at the optimum 2
1
D
-2
1
D
temperature may be low, so it seems reasonable to assume the 3
1
T
but not the 3
2
He
gets burned up and adds its energy to the net reaction. Thus we count the 2
1
D
-2
1
D
fusion energy as Efus = (4.03+17.6+3.27)/2 = 12.5 MeV and the energy in charged particles as Ech = (4.03+3.5+0.82)/2 = 4.2 MeV.

Another unique aspect of the 2
1
D
-2
1
D
reaction is that there is only one reactant, which must be taken into account when calculating the reaction rate.

With this choice, we tabulate parameters for four of the most important reactions

fuel Z Efus [MeV] Ech [MeV] neutronicity
2
1
D
-3
1
T
1 17.6 3.5 0.80
2
1
D
-2
1
D
1 12.5 4.2 0.66
2
1
D
-3
2
He
2 18.3 18.3 ~0.05
p+-11
5
B
5 8.7 8.7 ~0.001

The last column is the neutronicity of the reaction, the fraction of the fusion energy released as neutrons. This is an important indicator of the magnitude of the problems associated with neutrons like radiation damage, biological shielding, remote handling, and safety. For the first two reactions it is calculated as (Efus-Ech)/Efus. For the last two reactions, where this calculation would give zero, the values quoted are rough estimates based on side reactions that produce neutrons in a plasma in thermal equilibrium.

Of course, the reactants should also be mixed in the optimal proportions. This is the case when each reactant ion plus its associated electrons accounts for half the pressure. Assuming that the total pressure is fixed, this means that density of the non-hydrogenic ion is smaller than that of the hydrogenic ion by a factor 2/(Z+1). Therefore the rate for these reactions is reduced by the same factor, on top of any differences in the values of <σv>/T2. On the other hand, because the 2
1
D
-2
1
D
reaction has only one reactant, the rate is twice as high as if the fuel were divided between two hydrogenic species, thus creating a more efficient reaction.

Thus there is a "penalty" of (2/(Z+1)) for non-hydrogenic fuels arising from the fact that they require more electrons, which take up pressure without participating in the fusion reaction. (It is usually a good assumption that the electron temperature will be nearly equal to the ion temperature. Some authors, however discuss the possibility that the electrons could be maintained substantially colder than the ions. In such a case, known as a "hot ion mode", the "penalty" would not apply.) There is at the same time a "bonus" of a factor 2 for 2
1
D
-2
1
D
because each ion can react with any of the other ions, not just a fraction of them.

We can now compare these reactions in the following table.

fuel <σv>/T2 penalty/bonus reactivity Lawson criterion power density (W/m3/kPa2) relation of power density
2
1
D
-3
1
T
1.24×10−24 1 1 1 34 1
2
1
D
-2
1
D
1.28×10−26 2 48 30 0.5 68
2
1
D
-3
2
He
2.24×10−26 2/3 83 16 0.43 80
p+-6
3
Li
1.46×10−27 1/2 1700 0.005 6800
p+-11
5
B
3.01×10−27 1/3 1240 500 0.014 2500

The maximum value of <σv>/T2 is taken from a previous table. The "penalty/bonus" factor is that related to a non-hydrogenic reactant or a single-species reaction. The values in the column "reactivity" are found by dividing 1.24×10−24 by the product of the second and third columns. It indicates the factor by which the other reactions occur more slowly than the 2
1
D
-3
1
T
reaction under comparable conditions. The column "Lawson criterion" weights these results with Ech and gives an indication of how much more difficult it is to achieve ignition with these reactions, relative to the difficulty for the 2
1
D
-3
1
T
reaction. The last column is labeled "power density" and weights the practical reactivity with Efus. It indicates how much lower the fusion power density of the other reactions is compared to the 2
1
D
-3
1
T
reaction and can be considered a measure of the economic potential.

### Bremsstrahlung losses in quasineutral, isotropic plasmas

The ions undergoing fusion in many systems will essentially never occur alone but will be mixed with electrons that in aggregate neutralize the ions' bulk electrical charge and form a plasma. The electrons will generally have a temperature comparable to or greater than that of the ions, so they will collide with the ions and emit x-ray radiation of 10–30 keV energy (Bremsstrahlung). The Sun and stars are opaque to x-rays, but essentially any terrestrial fusion reactor will be optically thin for x-rays of this energy range. X-rays are difficult to reflect but they are effectively absorbed (and converted into heat) in less than mm thickness of stainless steel (which is part of a reactor's shield). The ratio of fusion power produced to x-ray radiation lost to walls is an important figure of merit. This ratio is generally maximized at a much higher temperature than that which maximizes the power density (see the previous subsection). The following table shows the rough optimum temperature and the power ratio at that temperature for several reactions.[21]

fuel Ti (keV) Pfusion/PBremsstrahlung
2
1
D
-3
1
T
50 140
2
1
D
-2
1
D
500 2.9
2
1
D
-3
2
He
100 5.3
3
2
He
-3
2
He
1000 0.72
p+-6
3
Li
800 0.21
p+-11
5
B
300 0.57

The actual ratios of fusion to Bremsstrahlung power will likely be significantly lower for several reasons. For one, the calculation assumes that the energy of the fusion products is transmitted completely to the fuel ions, which then lose energy to the electrons by collisions, which in turn lose energy by Bremsstrahlung. However, because the fusion products move much faster than the fuel ions, they will give up a significant fraction of their energy directly to the electrons. Secondly, the plasma is assumed to be composed purely of fuel ions. In practice, there will be a significant proportion of impurity ions, which will then lower the ratio. In particular, the fusion products themselves must remain in the plasma until they have given up their energy, and will remain some time after that in any proposed confinement scheme. Finally, all channels of energy loss other than Bremsstrahlung have been neglected. The last two factors are related. On theoretical and experimental grounds, particle and energy confinement seem to be closely related. In a confinement scheme that does a good job of retaining energy, fusion products will build up. If the fusion products are efficiently ejected, then energy confinement will be poor, too.

The temperatures maximizing the fusion power compared to the Bremsstrahlung are in every case higher than the temperature that maximizes the power density and minimizes the required value of the fusion triple product. This will not change the optimum operating point for 2
1
D
-3
1
T
very much because the Bremsstrahlung fraction is low, but it will push the other fuels into regimes where the power density relative to 2
1
D
-3
1
T
is even lower and the required confinement even more difficult to achieve. For 2
1
D
-2
1
D
and 2
1
D
-3
2
He
, Bremsstrahlung losses will be a serious, possibly prohibitive problem. For 3
2
He
-3
2
He
, p+-6
3
Li
and p+-11
5
B
the Bremsstrahlung losses appear to make a fusion reactor using these fuels with a quasineutral, isotropic plasma impossible. Some ways out of this dilemma are considered—and rejected—in Fundamental limitations on plasma fusion systems not in thermodynamic equilibrium by Todd Rider.[22] This limitation does not apply to non-neutral and anisotropic plasmas; however, these have their own challenges to contend with.

## References

1. ^ J.K. Shultis, R.E. Faw (2002). Fundamentals of nuclear science and engineering. CRC Press. p. 151. ISBN 0824708342.
2. ^ Hans A. Bethe, "The Hydrogen Bomb", Bulletin of the Atomic Scientists, April 1950, page 99. Fetched from books.google.com on 18 April 2011.
3. ^ "Progress in Fusion". ITER. Retrieved 2010-02-15.
4. ^ "The National Ignition Facility: Ushering in a New Age for Science". National Ignition Facility. Retrieved 2009-09-13.
5. ^ "DOE looks again at inertial fusion as potential clean-energy source", David Kramer, Physics Today, March 2011, p 26
6. ^ The Most Tightly Bound Nuclei. Hyperphysics.phy-astr.gsu.edu. Retrieved on 2011-08-17.
7. ^ F. Winterberg "Conjectured Metastable Super-Explosives formed under High Pressure for Thermonuclear Ignition"
8. ^ Zhang, Fan; Murray, Stephen Burke; Higgins, Andrew (2005) "Super compressed detonation method and device to effect such detonation"
9. ^ I.I. Glass and J.C. Poinssot "IMPLOSION DRIVEN SHOCK TUBE". NASA
10. ^ D.Sagie and I.I. Glass (1982) "Explosive-driven hemispherical implosions for generating fusion plasmas"
11. ^ T. Saito, A. K. Kudian and I. I. Glass "Temperature Measurements Of An Implosion Focus"
12. ^ S.E. Jones (1986). "Muon-Catalysed Fusion Revisited". Nature 321 (6066): 127–133. Bibcode 1986Natur.321..127J. doi:10.1038/321127a0.
13. ^ Access: Desktop fusion is back on the table: Nature News. Nature.com. Retrieved on 2011-08-17.
14. ^ Supplementary methods for “Observation of nuclear fusion driven by a pyroelectric crystal”. Main article Naranjo, B.; Gimzewski, J.K.; Putterman, S. (2005). "Observation of nuclear fusion driven by a pyroelectric crystal". Nature 434 (7037): 1115–1117. Bibcode 2005Natur.434.1115N. doi:10.1038/nature03575. PMID 15858570.
15. ^ UCLA Crystal Fusion. Rodan.physics.ucla.edu. Retrieved on 2011-08-17.
16. ^ Phil Schewe and Ben Stein (2005). "Pyrofusion: A Room-Temperature, Palm-Sized Nuclear Fusion Device". Physics News Update 729 (1).
17. ^ Coming in out of the cold: nuclear fusion, for real | csmonitor.com. Christiansciencemonitor.com. Retrieved on 2011-08-17.
18. ^ Nuclear fusion on the desktop ... really! – Science{{ndash}} MSNBC.com. MSNBC (2005-04-27). Retrieved on 2011-08-17.
19. ^ FusEdWeb | Fusion Education. Fusedweb.pppl.gov (1998-11-09). Retrieved on 2011-08-17.
20. ^ [1]
21. ^ [2]
22. ^ Portable Document Format (PDF)

Wikimedia Foundation. 2010.

### Look at other dictionaries:

• nuclear fusion — fusion (def. 4). [1895 1900] * * * Process by which nuclear reactions between light elements form heavier ones, releasing huge amounts of energy. In 1939 Hans Bethe suggested that the energy output of the sun and other stars is a result of fusion …   Universalium

• nuclear fusion — uclear fusion n. A type of nuclear reaction in which atomic nuclei combine to form more massive nuclei with the simultaneous release of energy. Syn: fusion, nuclear fusion reaction. [WordNet 1.5] …   The Collaborative International Dictionary of English

• nuclear fusion — n FUSION (3) …   Medical dictionary

• nuclear fusion — n [U] a ↑nuclear reaction in which the nuclei (=central parts) of atoms join together, which produces power without producing any waste …   Dictionary of contemporary English

• nuclear fusion — n. the fusion of lightweight atomic nuclei, as of tritium or deuterium, into a nucleus of heavier mass, as of helium, with a resultant loss in the combined mass, which is converted into energy: the principle of the hydrogen bomb …   English World dictionary

• Nuclear fusion — См. Термоядерный синтез Термины атомной энергетики. Концерн Росэнергоатом, 2010 …   Термины атомной энергетики

• nuclear fusion — noun uncount the process of combining the central parts of atoms, producing energy …   Usage of the words and phrases in modern English

• nuclear fusion — noun a nuclear reaction in which nuclei combine to form more massive nuclei with the simultaneous release of energy • Syn: ↑fusion, ↑nuclear fusion reaction • Hypernyms: ↑nuclear reaction • Hyponyms: ↑cold fusion, ↑thermonuclear re …   Useful english dictionary

• nuclear fusion — branduolių sintezė statusas T sritis fizika atitikmenys: angl. nuclear fusion; nucleosynthesis vok. Kernfusion, f; Kernverschmelzung, f rus. синтез ядер, m; слияние ядер, n pranc. fusion nucléaire, f; nucléosynthèse, f …   Fizikos terminų žodynas

• nuclear fusion — branduolių sintezė statusas T sritis chemija apibrėžtis Vienų atomų branduolių pavertimas kitais branduoliais. atitikmenys: angl. nuclear fusion; nucleosynthesis rus. синтез ядер; слияние ядер …   Chemijos terminų aiškinamasis žodynas