Electrical resistivity and conductivity
Electrical resistivity (also known as resistivity, specific electrical resistance, or volume resistivity) is a measure of how strongly a material opposes the flow of electric current. A low resistivity indicates a material that readily allows the movement of electric charge. The SI unit of electrical resistivity is the ohm metre (Ωm). It is commonly represented by the Greek letter ρ (rho).
Electrical conductivity or specific conductance is the reciprocal quantity, and measures a material's ability to conduct an electric current. It is commonly represented by the Greek letter σ (sigma), but κ (esp. in electrical engineering) or γ are also occasionally used. Its SI unit is siemens per metre (S·m−1) and CGSE unit is reciprocal second (s−1):
Electrical resistivity ρ (Greek: rho) is defined by,
- ρ is the static resistivity (measured in ohm-metres, Ω-m)
- E is the magnitude of the electric field (measured in volts per metre, V/m),
- J is the magnitude of the current density (measured in amperes per square metre, A/m²),
and E and J are both inside the conductor.
Many resistors and conductors have a uniform cross section with a uniform flow of electric current and are made of one material. (See the diagram to the right.) In this case, the above definition of ρ leads to:
- R is the electrical resistance of a uniform specimen of the material (measured in ohms, Ω)
- is the length of the piece of material (measured in metres, m)
- A is the cross-sectional area of the specimen (measured in square metres, m²).
The reason resistivity has the dimension units of ohm-metres can be seen by transposing the definition to make resistance the subject:
The resistance of a given sample will increase with the length, but decrease with greater cross-sectional area. Resistance is measured in ohms. Length over area has units of 1/distance. To end up with ohms, resistivity must be in the units of "ohms × distance" (SI ohm-metre, US ohm-inch).
In a hydraulic analogy, increasing the cross-sectional area of a pipe reduces its resistance to flow, and increasing the length increases resistance to flow (and pressure drop for a given flow).
The above scalar equation:
is only valid for resistors and conductors which are homogeneous and isotropic, that is the conductivity is uniform throughout the conductor, carrying a uniform electric current per unit cross-sectional area J, through a uniform internal electric field E, all in one dimension only.
For all three dimensions we have at all points (r = position vector at a point in the conductor):
in which (1, 2, 3 refer to components)
This is still only true if E and J are collinear, under the same conditions as above.
Since E and J are generally vector fields, the material may not be homogeneous or isotropic so the conductivity may vary from point to point, and the E and J are not always collinear at the same point, the definition generalizes by treating conductivity as a rank-2 tensor field σ:
where rank-2 tensors can be represented by matrices
equivalent to the matrix equation
which allows a simple relation between components to be read off, using the Einstein summation convention;
The above tensor equation serves as a definition for the conductivity tensor (or field). A similar analysis for resistivity can be done, introducing a resistivity tensor (or field) in an identical form,
Resistivity of various materials
- A conductor such as a metal has high conductivity and a low resistivity.
- An insulator like glass has low conductivity and a high resistivity.
- The conductivity of a semiconductor is generally intermediate, but varies widely under different conditions, such as exposure of the material to electric fields or specific frequencies of light, and, most important, with temperature and composition of the semiconductor material.
The degree of doping in semiconductors makes a large difference in conductivity. To a point, more doping leads to higher conductivity. The conductivity of a solution of water is highly dependent on its concentration of dissolved salts, and other chemical species that ionize in the solution. Electrical conductivity of water samples is used as an indicator of how salt-free, ion-free, or impurity-free the sample is; the purer the water, the lower the conductivity (the higher the resistivity). Conductivity measurements in water are often reported as specific conductance, relative to the conductivity of pure water at 25 °C. An EC meter is normally used to measure conductivity in a solution.
Material ρ [Ω·m] at 20 °C σ [S/m] at 20 °C Temperature
Reference Silver 1.59×10-8 6.30×107 0.0038  Copper 1.68×10-8 5.96×107 0.0039  Annealed Copper[note 2] 1.72×10-8 5.80×107  Gold[note 3] 2.44×10-8 4.10×107 0.0034  Aluminium[note 4] 2.82×10-8 3.5×107 0.0039  Calcium 3.36×10-8 2.98×107 0.0041 Tungsten 5.60×10-8 1.79×107 0.0045  Zinc 5.90×10-8 1.69×107 0.0037  Nickel 6.99×10-8 1.43×107 0.006 Lithium 9.28×10-8 1.08×107 0.006 Iron 1.0×10-7 1.00×107 0.005  Platinum 1.06×10-7 9.43×106 0.00392  Tin 1.09×10-7 9.17×106 0.0045 Lead 2.2×10-7 4.55×106 0.0039  Titanium 4.20×10-7 2.38×106 X Manganin 4.82×10-7 2.07×106 0.000002  Constantan 4.9×10-7 2.04×106 0.000008  Stainless steel[note 5] 6.897×10-7 1.450×106  Mercury 9.8×10-7 1.02×106 0.0009  Nichrome[note 6] 1.10×10-6 9.09×105 0.0004  Carbon (amorphous) 5×10-4 to 8×10-4 1.25 to 2×103 −0.0005  Carbon (graphite)[note 7] 2.5e×10-6 to 5.0×10-6 ⊥basal plane
3.0×10−3 //basal plane
2 to 3×105 ⊥basal plane
3.3×102 //basal plane
 Carbon (diamond)[note 8] 1×1012 ~10-13  Germanium[note 8] 4.6×10-1 2.17 −0.048  Sea water[note 9] 2×10-1 4.8  Drinking water[note 10] 2×101 to 2×103 5×10-4 to 5×10-2  Deionized water[note 11] 1.8×105 5.5 × 10−6  Silicon[note 8] 6.40×102 1.56×10-3 −0.075  GaAs 5×10-7 to 10×10-3 5×10-8 to 103  Glass 10×1010 to 10×1014 10-11 to 10-15 ?  Hard rubber 1×1013 10-14 ?  Sulfur 1×1015 10-16 ?  Air 1.3×1016 to 3.3×1016 3 to 8 × 10−15  Paraffin 1×1017 10-18 ? Quartz (fused) 7.5×1017 1.3×10-18 ?  PET 10×1020 10-21 ? Teflon 10×1022 to 10×1024 10-25 to 10-23 ?
The effective temperature coefficient varies with temperature and purity level of the material. The 20 °C value is only an approximation when used at other temperatures. For example, the coefficient becomes lower at higher temperatures for copper, and the value 0.00427 is commonly specified at 0 °C. For further reading: http://library.bldrdoc.gov/docs/nbshb100.pdf.
The extremely low resistivity (high conductivity) of silver is characteristic of metals. George Gamow tidily summed up the nature of the metals' dealings with electrons in his science-popularizing book, One, Two, Three...Infinity (1947): "The metallic substances differ from all other materials by the fact that the outer shells of their atoms are bound rather loosely, and often let one of their electrons go free. Thus the interior of a metal is filled up with a large number of unattached electrons that travel aimlessly around like a crowd of displaced persons. When a metal wire is subjected to electric force applied on its opposite ends, these free electrons rush in the direction of the force, thus forming what we call an electric current." More technically, the free electron model gives a basic description of electron flow in metals.
In general, electrical resistivity of metals increases with temperature, while the resistivity of intrinsic semiconductors decreases with increasing temperature. In both cases, electron–phonon interactions can play a key role. At high temperatures, the resistance of a metal increases linearly with temperature. As the temperature of a metal is reduced, the temperature dependence of resistivity follows a power law function of temperature. Mathematically the temperature dependence of the resistivity ρ of a metal is given by the Bloch–Grüneisen formula:
where ρ(0) is the residual resistivity due to defect scattering, A is a constant that depends on the velocity of electrons at the Fermi surface, the Debye radius and the number density of electrons in the metal. ΘR is the Debye temperature as obtained from resistivity measurements and matches very closely with the values of Debye temperature obtained from specific heat measurements. n is an integer that depends upon the nature of interaction:
- n=5 implies that the resistance is due to scattering of electrons by phonons (as it is for simple metals)
- n=3 implies that the resistance is due to s-d electron scattering (as is the case for transition metals)
- n=2 implies that the resistance is due to electron–electron interaction.
As the temperature of the metal is sufficiently reduced (so as to 'freeze' all the phonons), the resistivity usually reaches a constant value, known as the residual resistivity. This value depends not only on the type of metal, but on its purity and thermal history. The value of the residual resistivity of a metal is decided by its impurity concentration. Some materials lose all electrical resistivity at sufficiently low temperatures, due to an effect known as superconductivity.
An even better approximation of the temperature dependence of the resistivity of a semiconductor is given by the Steinhart–Hart equation:
where A, B and C are the so-called Steinhart–Hart coefficients.
This equation is used to calibrate thermistors.
In non-crystalline semi-conductors, conduction can occur by charges quantum tunnelling from one localised site to another. This is known as variable range hopping and has the characteristic form of , where n=2,3,4 depending on the dimensionality of the system.
Complex resistivity and conductivity
When analyzing the response of materials to alternating electric fields, in applications such as electrical impedance tomography, it is necessary to replace resistivity with a complex quantity called impeditivity (in analogy to electrical impedance). Impeditivity is the sum of a real component, the resistivity, and an imaginary component, the reactivity (in analogy to reactance). The magnitude of Impeditivity is the square root of sum of squares of magnitudes of resistivity and reactivity.
Conversely, in such cases the conductivity must be expressed as a complex number (or even as a matrix of complex numbers, in the case of anisotropic materials) called the admittivity. Admittivity is the sum of a real component called the conductivity and an imaginary component called the susceptivity.
An alternative description of the response to alternating currents uses a real (but frequency-dependent) conductivity, along with a real permittivity. The larger the conductivity is, the more quickly the alternating-current signal is absorbed by the material (i.e., the more opaque the material is). For details, see Mathematical descriptions of opacity.
Resistivity density products
In some applications where the weight of an item is very important resistivity density products are more important than absolute low resistivity- it is often possible to make the conductor thicker to make up for a higher resistivity; and then a low resistivity density product material (or equivalently a high conductance to density ratio) is desirable. For example, for long distance overhead power lines— aluminium is frequently used rather than copper because it is lighter for the same conductance.
Material Resistivity [nΩ·m] Density [g/cm³] Resistivity-density product [nΩ·m·g/cm³] Sodium 47.7 0.97 46 Lithium 92.8 0.53 49 Calcium 33.6 1.55 52 Potassium 72.0 0.89 64 Beryllium 35.6 1.85 66 Aluminium 26.50 2.70 72 Magnesium 43.90 1.74 76.3 Copper 16.78 8.96 150 Silver 15.87 10.49 166 Gold 22.14 19.30 427 Iron 96.1 7.874 757
Silver, although it is the least resistive metal known, has a high density and does poorly by this measure. Calcium and the alkali metals make for the best products, but are rarely used for conductors due to their high reactivity with water and oxygen. Aluminium is far more stable. And the most important attribute, the current price, excludes the best choice: Beryllium.
- Conductivity near the percolation threshold
- Electric effective resistance
- Electrical resistivities of the elements (data page)
- Electrical resistivity imaging
- Ohm's law
- Sheet resistance
- SI electromagnetism units
- Skin depth
Notes and references
- ^ The numbers in this column increase or decrease the significand portion of the resistivity. For example, at 30 °C (303 K), the resistivity of silver is 1.65×10−8. This is calculated as Δρ = α ΔT ρo where ρo is the resistivity at 20 °C (in this case) and α is the temperature coefficient.
- ^ Referred to as 100% IACS or International Annealed Copper Standard. The unit for expressing the conductivity of nonmagnetic materials by testing using the eddy-current method. Generally used for temper and alloy verification of aluminium.
- ^ Gold is commonly used in electrical contacts because it does not easily corrode.
- ^ Commonly used for high voltage power lines
- ^ 18% chromium/ 8% nickel austenitic stainles steel
- ^ Nickel-Iron-Chromium alloy commonly used in heating elements.
- ^ Graphite is strongly anisotropic.
- ^ a b c The resistivity of semiconductors depends strongly on the presence of impurities in the material.
- ^ Corresponds to an average salinity of 35 g/kg at 20 °C.
- ^ This value range is typical of high quality drinking water and not an indicator of water quality
- ^ Conductivity is lowest with monoatomic gases present; changes to 1.2 × 10-4 upon complete de-gassing, or to 7.5×10-5 upon equilibration to the atmosphere due to dissolved CO2
- ^ Mathematical Methods for Physics and Engineering (3rd Edition), K.F. Riley, S.J. Bence, M.P. Hobson, Cambridge University Press, 2010, ISBN 9 780521 769718
- ^ a b c d e f g h i j k l m n o Serway, Raymond A. (1998). Principles of Physics (2nd ed ed.). Fort Worth, Texas; London: Saunders College Pub. p. 602. ISBN 0-03-020457-7.
- ^ a b c d Griffiths, David (1999) . "7. Electrodynamics". In Alison Reeves (ed.). Introduction to Electrodynamics (3rd edition ed.). Upper Saddle River, New Jersey: Prentice Hall. p. 286. ISBN 0-13-805326-X. OCLC 40251748.
- ^ http://physics.mipt.ru/S_III/t (PDF format; see page 2, table in the right lower corner)
- ^ a b Giancoli, Douglas C. (1995). Physics: Principles with Applications (4th ed ed.). London: Prentice Hall. ISBN 0-13-102153-2.
(see also Table of Resistivity)
- ^ John O'Malley, Schaum's outline of theory and problems of basic circuit analysis, p.19, McGraw-Hill Professional, 1992 ISBN 0070478244
- ^ Glenn Elert (ed.), "Resistivity of steel", The Physics Factbook, retrieved and archived 16 June 2011.
- ^ Y. Pauleau, Péter B. Barna, P. B. Barna, Protective coatings and thin films: synthesis, characterization, and applications, p.215, Springer, 1997 ISBN 0792343808.
- ^ Hugh O. Pierson, Handbook of carbon, graphite, diamond, and fullerenes: properties, processing, and applications, p.61, William Andrew, 1993 ISBN 0815513399.
- ^ Lawrence S. Pan, Don R. Kania, Diamond: electronic properties and applications, p.140, Springer, 1994 ISBN 0792395247.
- ^ Physical properties of sea water
- ^ Pashley, R. M.; Rzechowicz, M; Pashley, LR; Francis, MJ (2005). "De-Gassed Water is a Better Cleaning Agent". The Journal of Physical Chemistry B 109 (3): 1231. doi:10.1021/jp045975a. PMID 16851085.
- ^ Ohring, Milton (1995). Engineering materials science, Volume 1 (3rd edition ed.). p. 561.
- ^ Pawar, S. D.; Murugavel, P.; Lal, D. M. (2009). "Effect of relative humidity and sea level pressure on electrical conductivity of air over Indian Ocean". Journal of Geophysical Research 114: D02205. Bibcode 2009JGRD..11402205P. doi:10.1029/2007JD009716.
- ^ 
- Paul Tipler (2004). Physics for Scientists and Engineers: Electricity, Magnetism, Light, and Elementary Modern Physics (5th ed.). W. H. Freeman. ISBN 0-7167-0810-8.
Wikimedia Foundation. 2010.
Look at other dictionaries:
Electrical resistivity tomography — (ERT) or electrical resistivity imaging (ERI) is a geophysical technique for imaging sub surfaces structures from electrical measurements made at the surface, or by electrodes in one or more boreholes. It is closely related to the medical imaging … Wikipedia
Electrical conductivity — or specific conductivity is a measure of a material s ability to conduct an electric current. When an electrical potential difference is placed across a conductor, its movable charges flow, giving rise to an electric current. The conductivity σ… … Wikipedia
Resistivity — Electrical resistivity (also known as specific electrical resistance) is a measure of how strongly a material opposes the flow of electric current. A low resistivity indicates a material that readily allows the movement of electrical charge. The… … Wikipedia
Electrical impedance tomography — (EIT), is a medical imaging technique in which an image of the conductivity or permittivity of part of the body is inferred from surface electrical measurements. Typically conducting electrodes are attached to the skin of the subject and small… … Wikipedia
resistivity — /ree zis tiv i tee/, n. 1. the power or property of resistance. 2. Also called specific resistance. Elect. the resistance between opposite faces of a one centimeter cube of a given material; ratio of electric intensity to cross sectional area;… … Universalium
Electrical conductivity meter — An electrical conductivity meter. An electrical conductivity meter (EC meter) measures the electrical conductivity in a solution. Commonly used in hydroponics, aquaculture and freshwater systems to monitor the amount of nutrients, salts or… … Wikipedia
conductivity — 1. The power of transmission or conveyance of certain forms of energy, as heat, sound, and electricity, without perceptible motion in the conducting body. 2. The property, inherent in living protoplasm, of transmitting a state of excitation … Medical dictionary
conductivity — noun (plural ties) Date: 1837 the quality or power of conducting or transmitting: as a. the reciprocal of electrical resistivity b. the quality of living matter responsible for the transmission of and progressive reaction to stimuli … New Collegiate Dictionary
Electrical conduction — is the movement of electrically charged particles through a transmission medium (electrical conductor). The movement of charge constitutes an electric current. The charge transport may result as a response to an electric field, or as a result of… … Wikipedia
Conductivity (electrolytic) — The conductivity (or specific conductance) of an electrolyte solution is a measure of its ability to conduct electricity. The SI unit of conductivity is siemens per meter (S/m). Conductivity measurements are used routinely in many industrial and… … Wikipedia