Closure (container)

An aluminum bottle with a threaded aluminum screw closure

Closures are devices and techniques used to close or seal a bottle, jug, jar, tube, can, etc. Closures can be a cap, cover, lid, plug, etc.

Other types of containers such as boxes and drums may also have closures but are not discussed in this article.

Contents

Purpose of closures

Many containers and packages require a means of closing. It can be a separate device or seal or sometimes a integral latch or lock. Depending on the contents and container, closures have several functions:

  • Keep the container closed and the contents contained for the specified shelf life until time of opening
  • Provide a barrier to dirt, oxygen, moisture, etc. Control of permeation is critical to many types of products: foods, chemicals, etc.
  • Keep the product secure from undesired premature opening
  • Provide a means of reclosing or reusing the container
  • Assist in dispensing and use of product
  • Allow reasonable ease to open the container by the intended user. Difficult to open containers may cause wrap rage. The force or torque required to open a closure is an important consideration for packaging engineers.[1][2]

Many types of packaging with their closures are regulated for strength, safety, security, communication, recycling, and environmental requirements.

Types of closures

Closures need a means of attaching to the container with sufficient security. Threads, lugs, hinges, locks, adhesives, etc. are used.

Many closures need to have the ability to adjust to slight manufacturing variation in the container and the closure structure. Some closures are made of flexible material such as cork, rubber, or plastic foam. Often an o-ring or a closure liner (gasket made of pulp or foam cap liner) is used. Linerless closures often use a deformable plastic rim or structure to maintain the seal.

Secondary seals are common with sensitive products that may deteriorate or where extra security is needed. Foil or plastic innerseals are used on some bottles, Heat sealed lidding films are used on some tubs. External shrink bands, labels, and tapes are sometimes used outside the primary closure structure.

Screw top

A screw closure is a mechanical device which is screwed on and off of a threaded "finish" on a container. Either continuous threads (C-T) or lugs are used. Metal caps can be either preformed or in some instances, rolled on after application. Plastic caps may use several types of molded polymer.

Some screw tops have multiple pieces. For example, a mason jar often has a lid with a built in rubbery seal and a separate threaded ring or band.

Crown cap

Crown caps

Beverage bottles are frequently closed with crown beverage caps. These are shallow metal caps that are crimped into locking position around the head of the bottle.

Snap on

Some closures snap on . For opening , the top is designed to pry off or , break off, or have a built in dispenser.

Friction fit

Some containers have a loose lid for a closure. Laboratory glassware often has ground glass joints that allow the pieces to be fitted together easily.

An Interference fit or friction fit requires some force to close and open, providing additional security. Paint cans often have a friction fit plug.

Tamper-evident

Resistance to tampering is required for some types of products. Container closures can be one of several layers of packaging to deter tampering and to prodive evidence of attempts at tampering.

Dispensing

A wide variety of convenience dispensing features can be built in to closures. Spray bottles and cans with aerosol spray have special closure requirements. Pour spouts, measuring attachments, sifting devices, etc. are common.

Child-resistant

Child-resistant packaging or C-R packaging has special closures designed to reduce the risk of children ingesting dangerous items. This is often accomplished by the use of a special safety cap. It is required by regulation for prescription drugs, over-the-counter medications, pesticides, and household chemicals.

Examples

History

Early pottery and ceramic containers often had lids that fit reasonably snug onto the body of the container. The narrow necks of ancient amphora were closed with a plug of cork, wood, or ceramic and sealed with mortar.[3] Wooden Barrels often had bungholes closed by cork or wood bungs.

Some early tinplate cans were made with threaded necks for screw top closures.

Beverage bottles started using the Hutter Stopper in 1893. This involved a porcelain plug fitted with a rubber washer, which was then forced down into the lip of the bottle. This technique only works with carbonated beverages. The Hutter Stopper became standard in beer bottling in the late 1890s / early 1900s. Bail closures on bottles were invented by Henry William Putnam in 1859. These involved heavy wire bail attached to a bottle's neck that swung over the cork to hold it in.

The world's first modern bottle cap, the crown cork, was invented by William Painter in 1890 in Baltimore. The screw cap using rust resistant aluminum was first used in prescription drug bottling in the 1920s.Molded urea based bottle caps were first introduced in the early 1900s.

A history of accidents involving children opening household packaging and ingesting the contents led the US Congress to pass the Poison Prevention Packaging Act of 1970.

The manufacture of closures

The Closure & Container Manufacturers Association is the main American trade association for closure manufacturers. It develops voluntary industry standards for its members to use in the manufacture of closures.

See also

References

  1. ^ Yaxall, A; Longley, Janson, Wearn, Manson (2006). "The Use of Uncertinty Analysis for Design of Container Closures". Packaging Technology and Science (Wiley) 19: 139–147. 
  2. ^ Carus, D. A.; Grant, Wattie, Pridham (2006). "Development and Validation of a Tequnique to Meassure and Compare the Opening Characteristics of Tamper-evident Bottle Closures". Packaging Technology and Science (Wiley) 19: 105–118. 
  3. ^ Tweede, D (June), "Commercial Amphoras, the First Consumer Package", Journal of Macromarketing 22, 1: 185–198, http://faculty.quinnipiac.edu/charm/CHARM%20proceedings/CHARM%20article%20archive%20pdf%20format/Volume%2010%202001/185%20twede.pdf 

Books

  • Brody, A. L., and Marsh, K, S., "Encyclopedia of Packaging Technology", John Wiley & Sons, 1997, ISBN 0-471-06397-5
  • Soroka, W, "Fundamentals of Packaging Technology", IoPP, 2002, ISBN 1-930268-25-4

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Closure & Container Manufacturers Association — Logo of the Closure Container Manufacturers Association. The Closure Container Manufacturers Association (CCMA) is a trade association of manufacturers who produce closures and containers. Only manufacturers of plastic containers are represented… …   Wikipedia

  • Closure — may refer to: Closure (container) used to seal a bottle, jug, jar, can, or other container Closure (wine bottle), a stopper Closure (business), the process by which an organization ceases operations Closure (philosophy), a principle in… …   Wikipedia

  • Container compression test — The container compression test measures the compressive strength of packages such as boxes, drums, and cans. It usually provides a plot of deformation vs compressive force. It is commonly used to evaluate shipping containers made of corrugated… …   Wikipedia

  • Closure (computer science) — In computer science, a closure (also lexical closure, function closure, function value or functional value) is a function together with a referencing environment for the non local variables of that function.[1] A closure allows a function to… …   Wikipedia

  • closure — 1. The completion of a reflex pathway. 2. The place of coupling between stimuli in the establishment of conditioned learning. 3. To achieve or experience a sense of completion in a mental task. flask c. in dentistry, the procedure of bringing the …   Medical dictionary

  • Drum (container) — A standard, 55 US gallon / 44 Imperial gallon drum. A drum is a cylindrical container used for shipping bulk cargo. Drums can be made of steel, dense paperboard (commonly called a fiber drum), or plastics, and are generally used for the… …   Wikipedia

  • Chub (container) — One type of chub used for bulk sausaage A Chub is a type of container formed by a tube of flexible packaging material. The cylindrical p …   Wikipedia

  • Clamshell (container) — Raspberries in a plastic clamshell package Clamshell pack of screws …   Wikipedia

  • Lid (container) — Lid of a Tic Tac mint case A lid, also known as a cap, is part of a container, and serves as the cover or seal, usually one that completely closes the object. Contents 1 …   Wikipedia

  • Screw cap — A screw cap or closure is a common type of closure for bottles, jars, and tubes. Common screw closures: Plastic bottle with plastic screw cap, Dispensing closure for salad dressing (with inner seal), Break away closure for syrup, Dispensing pump… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.