Camshaft


Camshaft

The camshaft is an apparatus often used in piston engines to operate poppet valves. It consists of a cylindrical rod running the length of the cylinder bank with a number of oblong "lobes" or "cams" protruding from it, one for each valve. The cams force the valves open by pressing on the valve, or on some intermediate mechanism, as they rotate.

History

The first known cam and camshaft were invented in Iraq (Mesopotamia), described by Al-Jazari in 1206. [Georges Ifrah (2001). "The Universal History of Computing: From the Abacus to the Quatum Computer", p. 171, Trans. E.F. Harding, John Wiley & Sons, Inc. (See [http://www.banffcentre.ca/bnmi/programs/archives/2005/refresh/docs/conferences/Gunalan_Nadarajan.pdf] )] The cam and camshaft later appeared in European mechanisms from at least the 14th century, [A. Lehr (1981), "De Geschiedenis van het Astronomisch Kunstuurwerk", p. 227, Den Haag. (See [http://odur.let.rug.nl/~koster/musicbox/musicbox2.htm] )] or possibly earlier. [http://emp.byui.edu/DavisR/202/202C16.html retrieved June 21, 2007]

Timing

The relationship between the rotation of the camshaft and the rotation of the crankshaft is of critical importance. Since the valves control the flow of air/fuel mixture intake and exhaust gases, they must be opened and closed at the appropriate time during the stroke of the piston. For this reason, the camshaft is connected to the crankshaft either directly, via a gear mechanism, or indirectly via a belt or chain called a "timing belt" or "timing chain". In some designs the camshaft also drives the distributor and the oil and fuel pumps. Also on early fuel injection systems, cams on the camshaft would operate the fuel injectors.

In a two-stroke engine that uses a camshaft, each valve is opened once for each rotation of the crankshaft; in these engines, the camshaft rotates at the same rate as the crankshaft. In a four-stroke engine, the valves are opened only half as often; thus, two full rotations of the crankshaft occur for each rotation of the camshaft.

The timing of the camshaft can be advanced to produce better low end torque or it can be retarded to produce better high end toque.

Duration

Duration can often be confusing because manufacturers may select any lift point to advertise a camshaft's duration and sometimes will manipulate these numbers. The power and idle characteristics of a camshaft rated at .006" will be much different than one rated the same at .002". Whenever duration is quoted, be sure to note the lift at which it is given.

Many performance engine builders have learned to gauge a race profile's aggressiveness by looking at the duration at .020", .050" and .200". The .020" number determines how responsive the motor will be and how much low end torque the motor will make. The .050" number is used to estimate where peak power will occur, and the .200" number gives an estimate of the power potential.

In general, duration determines how many crankshaft degrees a camshaft maintains more than a given tappet lift.

Camshaft position

Depending on the location of the camshaft, the cams operate the valves either directly or through a linkage of pushrods and rockers. Direct operation involves a simpler mechanism and leads to fewer failures, but requires the camshaft to be positioned at the top of the cylinders. In the past when engines were not as reliable as today this was seen as too much bother, but in modern gasoline engines the overhead cam system, where the camshaft is on top of the cylinder head, is quite common. Some engines use two camshafts each for the intake and exhaust valves; such an arrangement is known as a "double" or "dual overhead cam" (DOHC), thus, a V engine may have four camshafts.

Maintenance

The rockers or cam followers sometimes incorporate a mechanism to adjust and set the valve play through manual adjustment, but most modern auto engines have hydraulic lifters, eliminating the need to adjust the valve lash at regular intervals as the valvetrain wears, and in particular the valves and valve seats in the combustion chamber.

Sliding friction between the surface of the cam and the cam follower which rides upon it is considerable. In order to reduce wear at this point, the cam and follower are both surface hardened, and modern lubricant motor oils contain additives specifically to reduce sliding friction. The lobes of the camshaft are usually slightly tapered, causing the cam followers or valve lifters to rotate slightly with each depression, and helping to distribute wear on the parts. The surfaces of the cam and follower are designed to "wear in" together, and therefore when either is replaced, the other should be as well to prevent excessive rapid wear. In some engines, the flat contact surfaces are replaced with rollers, which eliminate the sliding friction and wear but adds mass to the valvetrain.

Alternatives

In addition to mechanical friction, considerable force is required to overcome the valve springs used to close the engine's valves. This can amount to an estimated 25% of an engine's total output at idle, reducing overall efficiency. Some approaches to reclaiming this "wasted" energy include:
* Springless valves, like the desmodromic system employed today by Ducati
* Camless valvetrains using solenoids or magnetic systems have long been investigated by BMW and Fiat, and are currently being prototyped by Valeo and Ricardo
* The Wankel engine, a rotary engine which uses neither pistons nor valves, best known for being used by Mazda in the RX-7 and RX-8 sports cars.

ee also

* Sleeve valve
* Cylinder head porting
* Crankshaft

Gallery

Footnotes


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • camshaft — n. a shaft that has cams attached to it, forming part of a mechanical device. [WordNet 1.5] …   The Collaborative International Dictionary of English

  • camshaft — ► NOUN ▪ a shaft with one or more cams attached to it, especially one operating the valves in an internal combustion engine …   English terms dictionary

  • camshaft — [kam′shaft΄] n. a shaft of which a cam is an essential part, or to which a cam is fastened …   English World dictionary

  • camshaft — A shaft with cam lobes (bumps) which is driven by gears, a belt, or a chain from the crankshaft. The lobes push on the valve lifters to cause the valves to open and close. The camshaft turns at half the speed of the crankshaft. Also see double… …   Dictionary of automotive terms

  • camshaft — /kam shaft , shahft /, n. a shaft bearing integral cams. [1875 80; CAM + SHAFT] * * * ▪ engineering       in internal combustion engines, rotating shaft with attached disks of irregular shape (the cams), which actuate the intake and exhaust… …   Universalium

  • camshaft — UK [ˈkæmˌʃɑːft] / US [ˈkæmˌʃæft] noun [countable] Word forms camshaft : singular camshaft plural camshafts a bar in an engine, fixed to a cam …   English dictionary

  • camshaft — [[t]kæ̱mʃɑːft, ʃæft[/t]] camshafts N COUNT A camshaft is a rod in an engine and works to change circular motion into motion up and down or from side to side …   English dictionary

  • camshaft — A straight, gear driven shaft that contains lobes used to operate the intake and exhaust valves of a reciprocating engine. The camshaft is geared to the crankshaft in such a way that valves close and open at the correct time relative to the… …   Aviation dictionary

  • camshaft — kumštelinis velenas statusas T sritis automatika atitikmenys: angl. camshaft vok. Exzenterwelle, f; Nockenwelle, f rus. кулачковый вал, m; распределительный вал, m pranc. arbre à cames, m …   Automatikos terminų žodynas

  • camshaft — noun Date: 1847 a shaft to which a cam is fastened or of which a cam forms an integral part …   New Collegiate Dictionary


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.