Stamping simulation


Stamping simulation

Stamping simulation, is a technology that calculates the process of sheet metal stamping, predicting common defects such as splits, wrinkles, springback and material thinning. Also known as forming simulation, the technology is a specific application of non-linear finite element analysis. The technology has many benefits in the manufacturing industry, especially the automotive industry, where lead time to market, cost and lean manufacturing are critical to the success of a company.

Recent research by the Aberdeen research company (October 2006) found that the most effective manufacturers spend more time simulating upfront and reap the rewards towards the end of their projects. [http://www.aberdeen.com/summary/report/benchmark/BM_Simulation_driven_Design_3591.asp]

Stamping simulation is used when a sheet metal part designer or toolmaker desires to assess the likelihood of successfully manufacturing a sheet metal part, without the expense of making a physical tool. Stamping simulation allows any sheet metal part forming process to be simulated in the virtual environment of a PC for a fraction of the expense of a physical tryout.

Results from a stamping simulation allow sheet metal part designers to assess alternative designs very quickly to optimize their part for low cost manufacture.

Capabilities of Stamping Simulation

Material yield (utilisation) calculations and blank shape estimates: Using a 3D CAD model of the final part, the data is meshed automatically and then “unrolled” or developed to a flat blank shape. From here blank nesting and rectangular, trapezoid or any other shape fitting can be applied. The final data produced is a 2D CAD line which can then be used to calculate material utilisation across any blank nesting or shape configurations.

Tip angles (or part tipping) and undercut checks: Using the 3D CAD of the final part shape, the data is automatically tipped into the most suitable pressing angle with the intent to ensure no elements in the mesh “undercut” the vertical motion of a press machine. This step provides a very quick indication of the possibility of forming the desired part shape in one process or if there is a need to do it in two or three or more processes. If there are undercutting areas, they are highlighted and decision can be made as to whether the part shape can be changed (to avoid the undercutting) or if an additional forming process is needed. This step sets the press tip angles and positions the 3D CAD model into the pressing coordinate system, ready for further die face designing.

Forming simulation (or drawing simulation): Stamping Simulation software can deliver a lot more than just a simulation of the forming process. The first step in the process is to create die face data. Using the final part shape that has been tipped in to the pressing direction, die face surfaces are created. In a simple crash form, the boundaries of the part simply need to be extended, but in a draw process addendum and binder surfaces need to be created. With this, the earlier developed blank shape (square, pre-trimmed or otherwise) is used with the newly created die face surfaces to run the simulation. [http://www.stampingsimulation.com/news/2007/06/22/the-capabilities-of-simulation.html]

Splitting, thinning and wrinkling checks: The primary purpose of the forming simulation step is to check how the material behaves prior to machining of any tool steel. The results produced in the forming simulation step illustrate very clearly the calculated areas of material yielding (splitting), amounts of necking (thinning or changes in thickness) and areas of material compression (wrinkles and folds). The Forming Limit Diagram (FLD) is key to analyzing this data as it plots each element’s strain (in major and minor axis) on a graph and compares it to the material’s limits to determine if any of these defects will be present. With this information in hand, countermeasures and adjustments are made to the die face design and then the forming simulation is re-run, until each defect is removed or an acceptable result is achieved.

Die face data export: Once all the problems have been ironed out of the draw process and an acceptable “draw panel” has been produced in the virtual environment, the die face data that was used in the simulation can be export as CAD (igs, stl or any other format) for use when designing a complete tool and creating NC cutter paths. Basically, the die face data can be used in any other CAD/CAM package for use in an actual tool build.

Blank shape development: There are many cases where it is not possible to simply blank the material to the shape estimated in the first step (blank shape estimate), form it and end up with a perfect result. If the part needs to be drawn then wiped down for example, then some trimming occurs aftering drawing and needs to be developed so that after the wipe down, the trim length is correct. With the simulation software, this can all be done in a virtual environment. After the draw simulation step is complete, the “virtual draw panel” can be virtually “laser trimmed” then wiped or flanged down. The virtual laser trim shape can then be adjusted until the final trim line is developed to the correct shape. This means when the time comes to develop an actual trim die, a very accurate starting point is available, which rarely needs further adjustment meaning the time and cost to build a real trim die, is drastically reduced.

Multiple stage forming: If a part cannot be formed in a single stage then each subsequent stage can be simulated and checked too. It is simply a matter of taking the result from the previous stage and feeding it into the next. The previous stage results may include a draw, a trim, a hole pierce or any other operation, all of which gets carried over into the next stage’s simulation.

Pierce hole roundness checks: A simulation of a hole pierced in a blank, then formed can be performed. This gives an accurate simulation of whether a hole can be safely pierced in a blank stage then drawn, without losing it’s roundness or desired position (usually determined by the quality specification of the final part). Conversly, such a simulation may show that an unimportant hole will go “egg shaped” after forming but if acceptable, it can remain as a hole pierced in the blank, as opposed to piercing it last when maybe a cam unit or otherwise would be required.

Springback check: A springback check can be performed after any stage. For example, after the first draw stage or after the final stage. The end result is not just a number on paper of the amount of springback, but a full 3D CAD model of the part in the sprung back state (and can be exported in any CAD format). This means it is very easy to use this data to counteract the spring back or decide whether the amount of springback is acceptable or not. [http://www.stampingsimulation.com/news/2007/06/22/the-capabilities-of-simulation.html]

Associated Sites

Stamping Simulation Software providers

[http://www.esi-group.com/products/metal-forming/pam-stamp-2g ESI Group PAM-STAMP 2G]

[http://www.autoform.com Autoform Engineering GmbH]

[http://www.eta.com Engineering Technology Associates Inc]

[http://www.forming.com Forming Technologies Inc]

[http://www.stampingsimulation.com StampingSimulation.com Pty Ltd]


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Stamping (metalworking) — Contents 1 Operations 2 Simulation 3 See also 4 References …   Wikipedia

  • Business and Industry Review — ▪ 1999 Introduction Overview        Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… …   Universalium

  • LS-DYNA — is an advanced general purpose multiphysics simulation software package that is actively developed by the Livermore Software Technology Corporation (LSTC). While the package continues to contain more and more possibilities for the calculation of… …   Wikipedia

  • PAM-CRASH — is a software package from ESI Group used for crash simulation and the design of occupant safety systems, primarily in the automotive industry. PAM CRASH enables automotive engineers to simulate the performance of a proposed vehicle design and… …   Wikipedia

  • Military equipment of Turkey — The military equipment of Turkey includes a wide array of arms, artilleries, large surface vessels, cannons, armored vehicles, mortars, unmanned vehicles and many different equipments. Contents 1 Historical development 1.1 General 1.2 1923 1950 …   Wikipedia

  • NX (software) — Infobox Software name = NX caption = NX screenshot developer = Siemens PLM Software latest release version = NX 6 latest release date = June 30, 2008 operating sy stem = Unix / Windows / Linux / Mac OS X genre = CAD software license = Proprietary …   Wikipedia

  • arts, East Asian — Introduction       music and visual and performing arts of China, Korea, and Japan. The literatures of these countries are covered in the articles Chinese literature, Korean literature, and Japanese literature.       Some studies of East Asia… …   Universalium

  • Electrical discharge machining — An electrical discharge machine Electric discharge machining (EDM), sometimes colloquially also referred to as spark machining, spark eroding, burning, die sinking or wire erosion,[1] is a manufacturing process whereby a desired shape is obtained …   Wikipedia

  • Brazil national football team — Infobox National football team Name = Brazil Badge = CBF logo.svg Badge size = 130px FIFA Trigramme = BRA Nickname = A Seleção (The Selection/National Team) Association = Confederação Brasileira de Futebol (Brazilian Football Confederation)… …   Wikipedia

  • History of ferrous metallurgy — Iron (material) redirects here. For the chemical element Fe, see Iron. Bloomery smelting during the Middle Ages. The history of ferrous metallurgy began far back in prehistory. The earliest surviving iron artifacts, from the 5th millennium BC in… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.