- Powered hang glider
A foot-launched powered hang glider (FLPHG), also called powered harness, nanolight or hangmotor, is a powered hang glider harness with a motor and
propellerin pusher configuration. An ordinary hang glideris used for its wingand control frame, and the pilot can foot-launch from a hill or from flat ground, needing an area of about the size of a football field to get airborne, or much less area if there is an oncoming breeze and an absence of obstacles. Although the main appeal of FLPHGs is to the already experienced hang glider pilot, interest in these machines is growing rapidly, particularly in areas where there are no hills for foot-launching.
The pilot can cruise around in good weather at speeds of 40 to 72 km/h (25 to 45 mi/h), but powered harnesses have limited power and
thrust, so are best used as a self-launch device in order to achieve enough altitude to find a warm-rising air thermalfor soaring.
Summary: Some glider flights have been recorded as early as 875 AD. [
Abbas Ibn Firnasflights in 875 AD near Cordoba, Spain. (Ibn Firnas crater on the Moon is named in his honor).] Most early glider designs did not fulfill safe flight; the problem was that early flight pioneers did not understand the underlying principles that made a bird's wingwork. Starting in the 1880s technical and scientific advancements were made that led to the first truly practical gliders. Otto Lilienthal, a German engineer, duplicated some of his contemporaries' work and greatly expanded on it from 1874. He rigorously documented his work, strongly influencing later designers; for this reason, Lilienthal is one of the best known and most influential early aviation pioneer. His type of aircraft is now known as a hang glider.
Francis Rogalloand Gertrude Rogallo together applied for a patent for a fully flexible wing, the "flexible wing" or Rogallo wing, which in 1957 the American space agency NASAbegan testing in various flexible and semi-rigid configurations in order to use it as a recovery system for the Gemini space capsules. The various stiffening formats and the wing's simplicity of design and ease of construction, capability of slow flight and gentle landing characteristics, did not go unnoticed by hang glider enthusiasts. Some designers soon adapted Rogallo's flexible wing airfoilonto elementary hang gliders, producing the most successful hang glider configuration in history.
The reaction of most pilots would be to say that powered
microlights (ultralights) developed from hang gliding in the late 1970s, but it was not that simple. In fact, microlights are a rebirth, a return to the love of low-speed flight which the earliest aviators felt so keenly, but which was subsequently lost in the quest for militarysuperiority. [In 1898 Augustus Moore Herringadapted a compressed air engine to a weight-shift biplane.
http://www.flyingmachines.org/hrrg.html] ] For a second time in aviation history, during the 1970s, motorization of simple gliders, especially those portable and foot-launched, became the goal of many inventors and gradually, small wing-mounted power packs were adapted. These early experiments went largely unrecorded, even in log books, let alone the press, because the pioneers were uncomfortably aware that the addition of an engine made the craft liable to registration, airworthiness legislation, and the pilot liable to expensive licensing and probably, insurance. Inventors from
Australia, Franceand Englandproduced several successful microlight motor gliders in the early 1970s [French aviation historians on FLPHG: [http://perso.orange.fr/pulma1/Un%20peu%20d'histoire.htm] ] and very few were portable wings.
Surprisingly, what really launched the powered
ultralight aviationmovement in the USAwas not the Rogallo flexible wing but a whole series of rigid-wing motorized hang gliders. [British Microlight Aircraft Association, History of Microlighting [http://www.bmaa.org/histdets.asp?HistoryID=4] ] The "Icarus V" flying wing appeared with its tip rudders and swept-back style wing - a rigid biplane designed by genius teen-ager Taras Kiceniuk, Jr, while Larry Mauro's "Easy Riser" biplane started to sell in large numbers. Hang gliding record holder Don Mitchell [ In April of 1946 Mitchell completed construction of his 'Flying Wing' (not the "Mitchell Wing" hang glider which was developed in 1975). The American FAAissued an Experimental Airworthiness number for it. The wing was flown as a glider by Mitchell, Bolwus and Paul Tuntland. Then Mitchell mounted a Nelson 2-cycle engine on it and flew it as a powered glider with wheels for landing gear. [http://home.earthlink.net/~mitchellwing/mitchell.html] ] fitted his BF-10 [In the early 1940s Don Mitchell first became involved with flying wing glider design and construction. But WWII interrupted his research and experiments. Then in 1974, with the advent of hang glider mania, the Mitchell Wing resurfaced. It was at that time Dr. Howard Long took an interest in the half-forgotten project and asked Mitchell to make him a flying wing hang glider. The result was the foot-launched Mitchell Wing, controllable by a 'joystick'. The Mitchell Wing astounded the world of hang gliding. George Worthington, holder of eight world records in hang gliding and author of the book "In Search of World Records", wrote in the book..."I predict that the Mitchell Wing will be the highest performance foot-launhced hang glider we'll see for a long time." He was right and it was from this preliminary design that Mitchell developed his later powered models: The B-10 and Mitchell U-2 Superwing.] with a motor, though he still used the pilot's legs as undercarriage, an arrangement which persisted until his "B-10 Mitchell Wing" [Don Mitchell - U.S. Pacific [http://home.earthlink.net/~mitchellwing/mitchell.html] , B-10 Photos: [http://home.earthlink.net/~mitchellwing/b10pics.html] ] appeared. Then there was the "Manta Fledge IIB", the "Pterodactyl" series, and the Quicksilver created in 1972 by Bob Lovejoy. But foot-launched powered hang gliding -as we know it today- had been unsuccessful prior to 1976 because three basic elements were unrefined:
*Most hang gliders had poor performance. [Flex-wing hang glider technology underwent a performance jump in 1980, when "Ultralight Products" released the revolutionary "Comet" hang glider.]
*Small engine technology was underpowered and unreliable.
*Piloting skills and experience were limited.
In 1963 and during his free time, aeronautical engineer Barry Palmer built and experimented with a foot-launched powered hang glider at
Bloomfield, Connecticut. It was powered by a Convert|7|hp|kW|0|abbr=on West Bend engine and mounted on top of a Rogallo-type flexible wing hang glider; the propeller was convert|3|ft|m|0 in diameter and was made of balsawood, covered with fiberglassand mounted in pusher configuration. But the engine was quite underpowered and the craft could not achieve flight. [Interview with Gerard Farell on Jan. 23-24, 2007. "Foot launched powered Para-wing around 1963, Convert|7|hp|kW|0|abbr=on West Bend driving a convert|3|ft|m|0|sing=on dia. glass over balsa propeller. Main structure is 6061-T6 aluminum tubing, 4 mil polyethylene. The craft was not particularly portable, the wind was always coming down the slight slope in Bloomfield, CT, and the project was terminated as I was re-engineering it with a bigger engine and as I got a job offer to move to Miami and design, build and fly the wheeled wings (trikes)."] It is now estimated that a modern flexible Rogallo winghang glider requires at least Convert|6|hp|kW|0|abbr=on at the prop shaft and about 45 lbf (200 N) of thrust just to maintain level flight. Barry Palmer build during 1967 what is likely the first weight-shift powered trike aircraft. [Recorded by the FAAas: Palmer Parawing D-6, serial 1A, N7144, was registered on 4/24/1967. No limitations were noted.]
In 1973, Australian Bill Bennett, who was one of the most skilled pilots of the time and the largest U.S.
hang glidermanufacturer, was following in Barry Palmer's footsteps and attempting to motorize a flexible hang glider. Bennett built a McCulloch engine backpack that drove a small caged propeller. It did not, however, work particularly well, as the prop was almost completely masked by his back, and what little efficiency remained was further reduced by the thick wire guard with which Bennett was prudent enough to surround the propeller. In practice, when used with the best hang glider of the day, it was nothing more than a glide extender.In the late 1970s, light two-stroke engines started to become more powerful and reliable and hang gliderpilots were developing their skills to such an extent that they no longer considered it normal to crash each time they flew. The only unanswered questions were where to fit the engine, the size and pitch of the propeller and how it was driven.
On March 15, 1975 John Moody successfully added a Convert|12.5|hp|kW|0|abbr=on West Bend engine with a 71 cm (28") propeller to an "Easy Riser" biplane hang glider designed by Larry Mauro. Moody opened the throttle and ran until he lifted from the frozen surface of a
lakewest of Racine, Wisconsinand he flew for 30 minutes. Then on July 27, 1976 John Moody demonstrated [Article in PDF format: "Powered hang glider, you can launch it any where " [http://www.pioneerflyer.com/articles/ps-article.pdf] ] ultralight aviation at the annual EAA fly-in convention in Oshkosh, Wisconsinwith a foot launched McCulloch 101 powered "Icarus II" [ Smithsonian Air & Space Museum. Icarus hang glider development. [http://www.nasm.si.edu/research/aero/aircraft/icarus.htm] ] in front of thousands of aviation-loving spectators, starting the modern ultralight aviationrevolution in the USA. Later he added wheels to the aircraft and by the end of 1979, there were almost 100 competing companies selling powered ultralights (microlights) but very few were foot-launchable.
During the mid 1970s in
England, Steve Hunt experimented by fitting a Scorpion glider with a McCulloch chainsawengine driving a keel-mounted ducted fanvia a reduction gear unit, but he stopped development "because it was too heavy". However, he visualized the need for a clutchunit to facilitate starting and to reduce shock loading on the drive system. Meanwhile, powered hang glider flight was progressing in the United Statesand in 1977 the Soarmaster company located in Scottsdale, Arizona, produced the first commercial foot-launched powered hang glider, the Soarmaster. The unit was recommended for fitting on an "Electra Flyer Cirrus" or "Olympus" hang glider, as the mounting brackets and thrust line calculations had been done for these two gliders only. The Soarmaster company had developed a two-stroke engine unit with splash box lubricated chain reduction system, clutch and long drive-shaft that bolted just below the hang glider keel. It produced about Convert|10|hp|kW|0|abbr=on for about of 80 lbf (360 N) of static thrust and sustained climb rate as high as 150 ft/min (0.762 m/s). The keel-mounted transmission rendered the aircraft pitch unstable under power so a fine balance existed between applying too much power, causing the aircraft to overtake the pilot or not enough power for flight. Though marginal and difficult to fly, the Soarmaster was an encouraging development, until strange accidents began to happen; when the pilot pushed out or stalled the wing, propeller-related injuries to their feet ensued, earning it nicknames such as "ToeMaster" and "SawMaster". It turned out that when the pilot went weightless or stalled under power, the glider would tuck forward violently because the line of thrustwas well above the centre of gravity.
In 1979, a powered backpack called Motolotnia - White Eagle, designed by Jerzy Kolecki, became available for sale. [ Power Up Company, United States Patent # 4546938 [http://www.freepatentsonline.com/4546938.html] ] [Powered backpack Motolotnia 80 White Eagle photo of advert in "Flight Line" magazine, march-June 1982 [http://commons.wikimedia.org/wiki/
] ] [Jerzy Kolecki, founder of Kolecki New Aviation Engineering,
Sweden)] It consisted of a 90 cc McCulloch chainsawengine with a direct drive 61 cm (24") wooden prop, producing a quoted 77 lbf (340 N) of thrust; the rate of climb was about 150 ft/min (0.76 m/s) and flight duration was limited by the small fuel tank and engine overheating after several minutes. Other powered harnesses to reach the market in the 1980s were The Ranger [The Ranger, designed by Bruce Hudson, UK. Powered by the Solo 210 cc engine: [http://perso.orange.fr/pulma1/Un%20peu%20d'histoire.htm] ] and the Relax 220. [Relax 220, designed by Yves Rousseau.] The first truly successful foot-launched powered harness was the Mosquito. It did not have a keel-mounted motor, but the complete power unit was incorporated in the harness' frame. The harness was hooked on to the glider by a regular hang strap, placing the center of masswell below the keel, the ideal position for effective weight-shift control and thrust transmission. The Mosquito was designed and produced by Swedish inventor Johan Åhling (Swedish AeroSport). Åhling's Mosquito flew first in 1987, but it had only 10 horsepowerand a few problems had to be worked out. When the Mosquito was released again in 1990 with a reliable 15 hp (10.2 kg, 118 cc) go-kart engine [Radne Raket 120, 118 cc, Convert|15|hp|kW|0|abbr=on, 10.2 kg + exhaust and reduction drive [http://www.radne.se/Store/Product/ProductList.aspx?CategoryID=24&N=9.1] ] its appeal grew first amongst European and Australian hang glider pilots, and it was not until the late 1990s that the Mosquito started to become somewhat popular in North America, that by then, was obsessed with larger and heavier ultralights and undergoing a decreasing hang glider pilot population. Åhling's Mosquito was later redesigned and released in 2000 as the NRG.
As of 2008, there are a few harness designs similar to the Mosquito/NRG, each sporting unique strengths, and produced by other FLPHG manufacturers. [FLPHG manufacturers: [http://www.wind-drifter.com/manuf.htm] ] The latest generation of powered harnesses bear names such as Wasp , [Wasp designers: Ed Cleasby and Chris Taylor - Wasp Flight Systems and Sperwill.] DoodleBug, [DoodleBug designer: Ben Ashman - Flylight Airsports Ltd.] Raven, [Raven designer: Randy Haney - Powerplanes] X1, [X1 designers: Kenneth M. O'Sage II and Dave Little - Hidden Mountain Flight.] Zenon, [Zenon designer: Sotos Christoforou - Sky Gear.] Explorer LD, [Explorer designer: Bob Bauer - Airtime Products. Created in 1997; discontinued in 2004 and released again in 2007 as the 'Explorer LD'] and Fillo. [Fillo manufacturer: Milan Vita.]
On April 30, 2003 a modified DoodleBug named 'JetBug' took to the skies over
Englandwhile powered by a 95 pounds force (420 N) thrust gasoline turbine engine. The JetBug was produced in collaboration between Flylight Airsports Ltd. and MicroJet Engineering; it was piloted first by Ben Ashman and then by Stewart Bond. Its flight autonomy was only of ten minutes at 1 Liter/min. The JetBug is an occasional guest at air shows across England.
La Fédération Aéronautique Internationale (FAI) is the international standard-setting and record-keeping body for
aeronauticsand astronautics, so it also oversees the official records by foot-launched powered hang gliders, currently under the RWF1 category. [FAI microlight world records, RWF1 (Weight-shift control, foot-launched and flown solo) [http://records.fai.org/microlight/] ] The Medium Ropuleim microlight piloted by Yves Rousseauholds the official foot-launched altitude and climb records. Somehow, these records are filed as foot-launched, however, this microlight was too heavy to be foot-launched and it made use of wheels to launch with a Convert|42|hp|kW|0|abbr=on Rotax447 motor. (Click here for a photo of a similar aircraft: [http://commons.wikimedia.org/wiki/
] , and here for a video: [http://www.youtube.com/watch?v=7in0pW-uOF0] ). Such records by the Medium Ropuleim do not reflect in any way the performance of true foot-launched powered hang gliders, with a total aircraft & fuel weight limited by a pilot's strength to lift it, run and land on his/her feet. A review of the RWF1 category, past records and their logical classification are in order.
Unofficial FLPHG World Records - Confirmed but not validated by the FAI.
* On October 1977, Trip Mellinger successfully flew his "Easy Riser" from mainland
Californiato Catalina Island some convert|42|km|mi offshore.
*On 5 August, 1978 French pioneer Bernard Danis mated a Soarmaster unit to this convert|168|m2|sqft|1 "SK 2SS" wing and climbed to convert|1825|m|ft above sea level at the
Southern Alps. [Bernard Danis [http://www.bmaa.org/histdets.asp?HistoryID=5] ]
*May 9th. 1978, David Cook becomes the first pilot to cross the
English Channelwhile flying on a foot-launched powered hang glider; he used a "JV 23F" glider. [French aviation historians on FLPHG: [http://perso.orange.fr/pulma1/Un%20peu%20d'histoire.htm] ]
* On 1979, American pilot Larry Mauro flew convert|162|km|mi on a foot-launched "Easy Riser" powered hang glider.
* On 7 May, 1979 British pilot Gerry Breen set a new distance record for FLPHG of convert|325|km|mi from
Walesto Norwich, a non-stop world distance record that still stands today; using a Soarmaster, the flight took about 4 hours with a tailwindof about convert|25|kn|mph and reportedly consumed convert|25|L|impgal of fuel. [Interview with Gerard Farell on November 2006.] Three months later, on August 25 through 28, inspired by the film " Those Magnificent Men in their Flying Machines" and sponsored by British Airways, Breen flew his powered hang glider from Londonto Paris: Wishing to use a British made aircraft, Gerry Breen and Steve Hunt set about building with their version of the powered Soarmaster, but had no clutch. The unit, including glider, was considerably heavier than the Soarmaster and "Olympus" glider combination but the wing was much more robust. The hang glider was a "Hiway Super Scorpion" with a Convert|10|hp|kW|0|abbr=on McCulloch 125 cc engine mounted on the keel just forward of the hang strap. [This powered hang glider, registered G-BGNL, is now held by the [http://www.british-hang-gliding-museum.co.uk/acatalog/index.html British Hang Gliding Museum] .] The journey was plagued with mechanical failures but Breen overcame them and completed the trip. [Despite this achievement, Breen and Hunt recognized the deficiencies of the keelmounted engine and when Breen saw a picture of Roland Magallon's trike in the French hang gliding magazine "Vol Libre", he mentioned that the days of the Soarmaster 'were numbered.']
* On July 2002, Italian hang gliding champion and conservationist,
Angelo d'Arrigo, guided a flock of 10 endangered Western Siberian Cranes, bred in captivity, with an Icaro hang glider equipped with an NRG powered harness convert|5300|km|mi from the Arctic circlein Siberia, across Kazakhstanto the shores of the Caspian Seain Iran, avoiding Afghanistanand Pakistanwhere they fall victim to the abundant guns. For the most part, he relied on the sun and wind for propulsion in order to teach the young cranes to soar long distances. This exhausting $250,000 USD experiment lasted for six months and finished in winter 2002. [Interview with Angelo d'Arrigo: [http://www.hgfa.asn.au//skysailor/Issues/0505/siberianmigration.htm] ] [Siberian Crane Flyway coordination. [http://www.sibeflyway.org/Reintroduction-Flight-of-Hope-Project-web.html] ] If repeated a few times, scientists hope the new migratory route will be passed on from parent to fledgling for generations of cranes to come.
* On 2005, Chris Street soared his Explorer harness and "Litesport" hang glider over Mt. Cook, in the
Southern Alps, New Zealand, at an altitude of convert|4114|m|ft above sea level (ASL) while aided by mountain wave lift.
* On April 24 2005, English pilot Stewart Bond flew his DoodleBug and "Aeros Discus-14" glider in still air at an altitude of convert|3706|m|ft ASL.
* On July 16 2005, American pilot Bruce Decker performed a convert|3048|m|ft high
density altitudetakeoff in Colorado, USA using an X1 harness on an "ATOS 146" rigid wing hang glider; the wind was only convert|4.8|km/h|mph.
* On September 13, 2008, Irish pilot Patrick Laverty broke the powered harness altitude world record when he flew his home-made supine custom-made harness equipped with a 29hp ROS 125 engine coupled to an "Aeros Discus 14" hang glider to an altitude of convert|4668|m|ft ASL over Talybont, Ceredigion,
Wales, UK. Takeoff was at 600ft ASL and the the engine was equipped with the "Tuna" carburation system. [The altitude was recorded by a digital altimeter, a GPSand the flight was filmed as well; Video: [http://www.youtube.com/watch?v=NtiANJ6lJqI] ]
Currently, there are two harness configurations: prone (face down) and supine (sitting). Both configurations allow the pilot to takeoff and land on his/her feet. Foot-launched powered hang glider (FLPHG) harnesses are built around a light metal frame with the engine and propeller mounted on the rear in a
pusher configuration. Current powered harnesses weigh 22-32 kg (50-70 lb) not including the safety parachuteand fuel, and fold neatly into a convert|1.5|m|ft long harness bag with a handle. Most powered harnesses in production are equipped with the 'Radne Raket 120' two strokeengine which is based on HusqvarnaXP3120 chainsawparts. It has a displacement of convert|118|cm3|cuin and produces about Convert|15|hp|kW|0|abbr=on at 8900 RPM if equipped with a tuned exhaust; when coupled to a 1:3.5 belt-driven reduction driveand a 52" x 22" propeller, it produces about 100 lbf (440 N) of static thrust. For heavy pilots or pilots operating from higher than convert|1500|m|ft MSL fields, a powered harness equipped with an Convert|18|hp|kW|0|abbr=on engine is recommended. [18 hp Harnesses such as the 'X1' or 'Wasp Venom' equipped with the Vittorazi EVO 100 cc for about 130 lbf (580 N) thrust at convert|7000|ft|m|-2|abbr=on MSL] It is now estimated that a modern flex wing hang glider requires of at least Convert|6|hp|kW|0|abbr=on at the propeller and about 30 or 40 lb of thrust to maintain level flight at 'best glide' speed.
The motor is supported on the ground by two retractable skids, holding the propeller just off the ground. The 4 Liter
aerodynamicfuel tank is attached to the top of the control frame or is enclosed in the harness. Getting into the harness requires passing both legs through padded straps and wearing the harness like a vest, with a zipperand/or buckles at the front. The powered harness is hooked to the glider via a regular hang strap. The whole aircraft is easily maneuvered on the ground into takeoff position with the pilot buckled into the harness and ready to start the unit by themselves either with a manual or with an electric starter. The throttleis activated during takeoff by means of a mouth-throttle in order to have both hands free for proper weight-shift control. Once airborne, a foot throttle, thumb throttle or cruise controlcan be used. Zipping up the harness also retract the rear skids, which are then clipped into clamps on the side of the harness. The propeller is locked in place while soaring power off, as a wind milling propeller has more drag than a stationary one: Expect a 10 to 20% decrease in glide performance with a wind milling propeller (clutched units) and 2 to 4% decrease with a locked propeller. A folding propeller is often preferred by pilots who enjoy optimum soaringand cross country performance with the engine turned off.
Engine controls - Hang gliders are controlled by simply shifting the pilot's weight, but a powered harness must have engine controls and the pilot must know exactly where they are, without having to look and find them. Engine controls are ergonomically positioned at the sides of the harness, chest or shoulder straps and generally consist of throttle, choke, propeller lock, recoil starter handle or electric starter button and decompression valve. During training, it is very important to hang the harness from a solid location, climb in and practice often so that the pilot can automatically reach and activate any engine control without first looking at it.
Training & safety
Hang gliding is an
extreme sportbut perhaps often viewed as a higher-risk sport than it actually is. Nonetheless, there is great potential for injury for the reckless or ill-prepared. Unlike powered paragliding, it is absolutely essential that the aspiring pilot first take lessons in an unpowered hang gliderat a certified school and achieve some solo experience in order to develop all needed skills to perform automatic control inputs and consistently safe landings. Tow is the best launch method for progression to FLPHG. Basic aerodynamics, flightconcepts, some meteorology, local regulations, field choice, safetyand emergency procedures must also be learned during training. [British Hang Gliding and Paragliding Association Ltd. - [http://www.bhpa.co.uk/members/documents/FLPA_Training_Syllabus.pdf FOOT LAUNCHED POWERED AIRCRAFT (FLPA) TRAINING SYLLABUS - POWERED HANG GLIDING] ]
It is sometimes said that the factor which most affects safety is pilot attitude. A large proportion of accidents involve over-confident novices failing to heed advice, or pilots flying beyond their limits. Flying often can keep the pilots' skills current.A major safety consideration is simply having a large enough field that is free of obstructions. The pilot must not assume about how fast he will climb or that the engine will not quit. The pilot needs to have a way to safely turn or land at all times during every flight.
Safety precautions include: Certified training, equipment maintenance, pre-flight checks of glider and harness systems, helmet, safety
wheels at the lower end of the control frame, helmet, a hook-knife (for cutting their parachute bridle after impact or cutting their harness lines and straps in case of a tree or water landing), and a special emergency parachute(Note that unlike skydiving reserve parachutes in which the main canopy is cut away before deployment, hang gliding& paraglidingreserves are designed to open at low speeds and deploy with the glider still attached to the pilot.) Water, knee pads, gloves a mobile phoneand/or a transceiver radioare also desired.
Launching and landing are done into
wind. Though it is possible to launch and land in nil wind, a steady 8 km/h (5 miles/h) breeze is ideal. A successful takeoff depends mostly on level wings, speed and precise control of the angle of attack: If the angle of attack is too low then the powered glider will simply not fly. If the angle of attack is too high, then excessive drag results in not getting the speed needed to fly and climb.
A committed and fast run is required with a smooth control of pitch angle throughout the run, similar to a shallow slope launch (see: aborting a takeoff). The pilot remains upright throughout the run--allowing forward acceleration to be gradually provided by the thrust, so the pilot does not use his legs to accelerate but only to carry the weight of him and the glider. By gradually increasing thrust the pilot has time to counter the pitch-up moment introduced by the thrust with an appropriate counter pitch-down control movement. The pilot runs as long as necessary, taking strides of ever increasing length ('moon walking') and during the last steps most of the pilot’s weight will be carried by the glider. There must be no noticeable change in pitch angle, and "the pilot will have stopped running only after the last steps no longer touch the ground".
Failure to remain upright throughout the takeoff run is one of the main problems that experienced mountain-glider pilots suffer, as their normal tendency is to move towards prone position as soon as they feel the glider lifting. But on a flat-ground powered takeoff, one does not have the hill dropping away to help achieve flying speed - "the pilot must keep running up until he is firmly established in a climb". What can often make the difference between a successful takeoff and settling back to earth are those last long 'moon walking' steps.
During the takeoff run, the
thrustmust be transmitted to the glider through the hang strap and not through the pilot's hands to the control frame. By the time the glider comes off the pilot's shoulders, he must pull in and move his upper body forward through the control frame so that the hang strap becomes tight and is angled slightly forward, all while he is still upright and running. Because the thrust force enters the glider right at the hang point, it only requires a light touch to control the pitch.
During takeoff, particularly if something has started to go wrong, a fierce grip of the down tubes may cause the engine torque to be transmitted through the pilot to the glider. A tight grip can induce a roll which may require a rapid decision to abort the takeoff. A light touch on the control bar at all times can help to avoid this. Pull in and allow the glider to fly on ground effect for as long as possible in order to accelerate - the glider will climb on its own once it has the speed to do so; use of a speed bar helps to pull in more effectively at this stage. "Resist the temptation to push out". Shortly after lift-off, many gliders will suddenly climb too fast - be prepared for this, pull in, and you will avoid a stall. The overall sensation and glider behavior is similar to that of being [http://www.questairforce.com/aero.html aero towed] or winch towed. A powered launch is easier to do well if you allow the glider to achieve flight from the trim position - so you want to make sure this glider trim speed is fast enough for safety. If you are trimmed exactly at minimum sink (very close to mush/stall) then it would be advisable to move the hang point forward to where you have good roll response and control authority without pulling in (when gliding power off). Setting the trim speed higher will mean you have to run a bit faster, but when you do get airborne it will be at a safer airspeed and there will be less drag for the motor to overcome.
Aborting a takeoff
Aborting a takeoff is an important procedure and experienced mountain glider pilots must note that this is an option for every powered takeoff. Unlike a mountain launch, where your best bet is usually to continue once begun, significant sorrow and money can be saved by aborting a powered harness takeoff if things are not going exactly right. To abort a takeoff do not just stop running; between yourself, the glider and the harness you will have a lot of momentum. First release the throttle while you continue running, then the drag of the harness' skids will help you to bleed off the momentum that both you and the glider have achieved, sense the speed and flare to a stop. If that fails, settle the glider on its safety wheels while pushing out the control bar and roll to a stop, then hit the kill switch.
Learning to let go of the mouth-throttle is "critical". When things start to go wrong, the general tendency is to clench up our jaws, which compounds the problem with unwanted thrust; letting go of the mouth-throttle is the equivalent of tow line release and must be done without hesitation when needed. It is very useful to practice releasing the mouth-throttle while under stress by using dynamic
Climb and cruise speeds
* Climb speedIn general, the pilot must use best glide speed for takeoff and climb. The pilot must not push out on takeoff or climb. Note that the glider will climb on increased speed. Using full VG from a safe height is beneficial to climb rate. Many pilots new to powered flying make this common error, they are tempted to 'push-out' on climb but that causes to fly too slowly. To an observer on the ground they appear to wobble around and lose directional control; to the pilot there is a feeling that the glider wants to wind into turns and the wing feels unstable. The cause is a lack of
airspeed. Pushing out will decrease airspeed -just as when free hang gliding- and the wing may stall. Even if it doesn't, it will certainly exhibit those nasty characteristics of slow speed flight- dropping a wing into turns and feeling unstable in roll, in short, the pilot will be in “mush mode” with very poor control authority.
As soon as it is safe, the pilot gets the feet into the harness for stability (or
supine positionif flying the DoodleBug). One must keep the wings level at all times, keep the control bar pulled in and be ready to correct any roll early on. Again, note that the best rate of climb occurs at higher airspeedand that most flexible wings climb well at convert|10|mi|km|0/h above their stall speed. Today's powered harnesses develop a maximum of 45 kg (100 lb) of static thrust, but the rate of climbalso depends on weather conditions such as field altitude, air temperature, humidity, etc., and on glider size and wing loading. The harness' thrust is adequate for a sustained 200 - 300 ft/min (1.0 - 1.5 m/s) rate of climbat full power even when flying at airspeeds well above minimum sink. If a powered harness experience an engine failure when climbing steeply, the aircraft will lose a lot of height before recovering; climbing at a flatter angle and at a faster airspeed makes recovery easier and safer.
* Cruise SpeedCruise speed varies between hang glider brand, model, size and wing loading. To cruise fast and level while under power, pilots apply about 75% throttle (~ 6600 rpm for the Raket 120) and increasingly pull in while glancing at the
variometeruntil top speed is achieved without descending. Flight autonomy with 4 Liters (approx. 1 Gallon) of fuel depends on throttlesettings, but it ranges between 60 and 90 minutes of continuous engine use.
Control bar position
Adding the motor weight behind one's feet in a prone configuration unit, moves the combined center of gravity lower on the pilot's body. Because the pilot is now located farther forward in relation to the hang point, the
control barwill appear to be further back by about Convert|25|cm|in. This apparent bar trim position change occurs without the addition of power. Note that the actual trim characteristics of the glider have not changed, only the pilot's position with respect to the control bar. Though this new bar position may be disconcerting to experienced hang glider pilots, it should be clear that the pilot must rely instead on feeling the bar pressure and remain aware of airspeed at all times. With more experience, the new powered pilot will learn the new bar positions and use them automatically when flying the powered harness. Replacing the base tube for a 'speed bar' is quite recommended.
Even very experienced hang glider pilots will need to learn some new tricks when it comes to turning under power. Most hang glider pilots were taught to 'lead with your feet' in making turns. This is effective for un-powered flight, but adding weight and thrust to our feet changes things. Note that full power turns will become increasingly unstable with increasing roll angle so once the glider gains enough altitude, most pilots reduce the throttle for easier control during turns, especially on the early training stage.
* Power on - Ideally, keep the harness (and thrust line) parallel with the
keelof the wing so that the thrust pushes forwards and not sideways; some pilots simply yaw their body momentarily as that changes the thrust line and helps engage a turn. Most pilots use a combination of both weight-shift and thrust line to turn under power. Novice FLPHG pilots must not attempt powered turns at low altitude. Medium power and shallow bank turns at a safe height are recommended for the first few flights so that the new FLPHG pilot can get a feel for the effects of thrust on glider behavior. If the glider enters a powered 'lockout' simply reduce the power and stabilize the wing as usual. Shallow and medium bank turns must be well coordinated to prevent the engine from 'falling' toward the lower side and engaging the glider on a diving turn.
* Power off - Turns in a prone unit hooked to a flex wing, require of a somewhat additional effort to weight-shift the center of gravity; because of the engine mass, some experienced pilots new to powered harnesses find that only the front half of their body moves, that is: they cross-control without an effective shift of their center of gravity. Keeping the body parallel to the keel for turns or corrections is easier than weight-shifting one's feet. Shallow and medium bank turns must be well coordinated to prevent the engine from 'falling' toward the lower side and engaging the glider on a diving turn.
* Limit Lines - The DoodleBug is a supine unit that uses limit lines at the rear to keep the engine & propeller relatively stationary; the port line is approx. 1 inch shorter than the starboard line, and are secured to the lower wing wire tangs so that sideways movement of the harness is restricted to convert|10.1|cm|in approximately on each side of dead centre. As the pilot moves to one side, this arrangement moves the thrust line so that it actually pushes in the turn direction. It is evident that this setup is beneficial in helping to create a more coordinated turn and also in stability while flying through turbulence. Some pilots flying prone configuration units like the freedom of being able to control the direction of thrust as it gives them another way to fine tune a turn. Prone configuration units do not require of limit lines but they are recommended during the early training stages. Limit lines may also offer help when moderate thermal turbulence is expected as they help prevent the engine from 'falling' toward the lower side of the turn or provoke oscillations. On the ground, the limit lines might also prevent propeller strikes to the trailing edge of the wing.
As usual, the pilot must plan the landing approach and execute it as planned in order to avoid sharp turns or sudden changes in
aircraft attitudes. The FLPHG pilot must get ready at higher altitude than usual in order to set a landing configuration: turn off the engine (optional), lock the propeller, the harness' legs have to be un-clipped and the harness unzipped, and it is a little more work than a normal pod harness, definitely not something to be trying to do on final. The engine may be left on idle (if equipped with a centrifugal clutch) during final glide and if the pilot decides to abort the landing, then the propeller brake is released and the mouth throttle activated.
But the landings are surprisingly easy: keep the speed up as usual and keep one leg straight and snug in the harness' boot for as long as possible to prevent the motor from swinging sideways. Bleed off speed on
ground effectand when you feel the harness' legs dragging, wait for the flare window appropriate for the glider and flaremildly. Your forward position and extra massgive you more flare authority than you are used to. The mass of the motor still wants to continue forward, so expect a feeling like a nudge from behind after you have landed, and be prepared to take a step or two.
Alternatively, running out the landing is possible as the rear skids generate enough drag against the ground to slow down the aircraft.
Although it started out as simply gliding down small hills on low performance wings, hang gliding over the last 120 years has evolved to the ability to soar for hours with hawks and eagles, gain thousands of feet of altitude in thermal updrafts, and fly cross country over distances of hundreds of miles. If the pilot finds lift, he/she may wish to shut off the engine and soar. While soaring, the propeller is locked or folded to reduce drag. In-flight engine restarts can be a powerful didactic tool for learning or improving thermalling skills, as the pilot does not have to land every time he does an incorrect decision and loses the lift. This brings about significant increase in soaring airtime and opportunities needed to better understand lift, usable cloud life, sink, drift, ridge lift, timing transition glides, etc.
While soaring a prone unit power off, the biggest difference will be the extra mass at one's feet when roll for a turn, which requires additional effort at stabilizing the wing during mild or moderate
turbulence. Unpowered glider pilots can stay airborne for hours. This is possible because they seek out rising air masses or lift from the following sources:
ThermalsThe most commonly used source of lift is created by the sun's energy heating the ground which in turn heats the air above it. This warm air rises in columns known as
thermals. Soaring pilots quickly become aware of visual indications of thermalssuch as: cumulus clouds, cloud streets, dust devils, soaring birds and haze domes. Having located a thermal, a glider pilot will circle within the area of rising air to gain height. In the case of a cloud street, thermals can line up with the wind creating rows of thermals and sinking air. A pilot can use a cloud street to fly long straightline distances by remaining in the row of rising air.
Ridge liftAnother form of lift occurs when the wind meets a mountain, cliff or hill. The air is deflected up the
windwardface of the mountain forming lift. Gliders can "surf" and climb in this rising air by flying along the feature. Another name for flying with ridge lift is slope soaring.
Mountain waveThe third main type of lift used by glider pilots are the
lee wavesthat occur near mountains. The obstruction to the airflow can generate standing waves with alternating areas of lift and sink. The top of each wave peak is often marked by lenticular cloudformations.
ConvergenceAnother form of lift results from the
convergenceof air masses, as with a sea-breeze front.
More exotic forms of lift are the polar vortexes which the
Perlan Projecthopes to use to soar to great altitudes. [Pelan project [http://perlanproject.com] ] A rare phenomenon known as Morning Glory has also been used by glider pilots in Australia. [ [http://www.dropbears.com/brough/index.html A Guide to the Morning Glory] at www.dropbears.com]
Hang Glider Selection
An ideal glider would be an intermediate model that has a low
stall speed, easy handling, good penetration and of the correct size. Consider that by adding about 40 lb to the hook-in weight, the free flying stall speedis increased by about 7% or 8% so a glider of appropriate size (hook in weight range) should be used. For first glider, the best choices are flexible gliders with single surface (novice) because of their low stall speed, ease of landing and gentle handling characteristics. Examples: Falcon II, Mark IV, Pulse, Eagle and Target, to name a few (2006).
stall speed- very important, especially for a beginner to FLPHG. Lower takeoff speeds are safer and less intimidating. Also good for higher altitudes.
* Easy Handling/Roll Stable - roll stability is important, especially for a beginner. A spirally unstable glider (some high performance gliders have been tuned that way to help initiate turns into thermals) will be more of a challenge while climbing under power.
* Good L/D (Lift/Drag ratio) - for maximum climb rate and best
glide ratio. A fast rigid wing will climb better than a floater. Good L/D is useful to pilots who enjoy soaring cross-country power off.
* Short to moderate root chord - for propeller clearance. All powered harnesses require the glider keel to be cut be cut off no further than Convert|119|cm|in behind the hang point; the cut off section can be sleeved and refitted to help rig the wing.
Medium and high performance flexible hang gliders may also be used but only by well experienced pilots. Most "rigid wing" hang gliders such as the Exxtacy, Axxess and ATOS accept the powered harness readily. Some pilots believe the Exxtacy to be the ultimate hang glider for flying with a powered harness because of its docility, high wing loading, penetration, ease of control with minimum weight-shift and the advantage of flaps, making the landings much easier.
In order to maximize a pilot's understanding of how the hang glider is flying, most pilots carry a series of small instruments, often interconnected. The most basic being an airspeed indicator, a variometer and altimeter. Many pilots also use two-way communication radios and some also carry a map and/or GPS unit. Some pilots also make use of a small
tachometerto ensure the engine is developing full power prior to takeoff. Hang gliders do not have instrument panels as such, so all the instruments are mounted on the control frame of the glider, except for the radio and tachometer which are mounted on the harness.
VariometerPeople can sense the
accelerationwhen they first enter a rising thermal, but they cannot detect the difference between constant rising air and constant sinking air, so they turn to technology for help. A variometeris a very sensitive vertical speed indicator; in other words, indicates climb or sink rate with audio signals (beeps) and/or a visual display. These units are generally electronic, vary in sophistication and often include, an altimeterand airspeed indicator. More advanced units often incorporate a barographfor recording flight data and/or a built in GPS. The main purpose of a variometer is in helping a pilot find and stay in the ‘core’ of a thermal to maximise height gain, and conversely indicating when he or she is in sinking air, and needs to find rising air.Variometers are sometimes capable of electronic calculations based on the 'MacCready Ring' to indicate the optimal speed to fly for given conditions. The MacCready theory solves the problem of how fast a pilot should cruise between thermals, given both the average lift the pilot expects in the next thermal climb, as well as the amount of lift or sink he encounters in cruise mode. Some electronic variometers make the calculations automatically, after allowing for factors such as the glider's theoretical performance (glide ratio), altitude, hook in weight and wind direction.
RadioPilots use radio for training purposes and when traveling on cross-country flights. Radios used are PTT (
push-to-talk) transceivers. Best range is achieved with FM VHF 2-meter band (144–148 MHz) radios. Usually a microphone and earphones are incorporated in the helmet and the PTT switch is strapped to a finger.
GPS(global positioning system) is a necessary navigation accessory when flying competitions, where it has to be demonstrated that way-points have been correctly passed. More common uses include being able to determine driftdue to the prevailing wind, providing position information to allow restricted airspaceto be avoided, and identifying one’s location for retrieval teams after landing-out in unfamiliar territory.It can also be interesting to view a GPS track of a flight when back on the ground, to analyze flying technique. Computer softwareis available which allows various different analyses of GPS tracks. [e.g: [http://www.compegps.com/new/products.php?var=1&tipoweb=1&todos=1&prod=16 CompeGPS.] ] More recently, the use of GPS data, linked to a computer, has enabled pilots to share 3D tracks of their flights on Google Earth. This fascinating insight allows comparisons between competing pilots to be made in a detailed 'post-flight' analysis.
Pros & contras
Some compromises and advantages when comparing a FLPHG with unpowered hang gliding:
*Glider launch autonomy. No crew required.
*Multiple takeoff areas available. No long drives.
*No need to invest a whole day in order to fly.
*Easy to face the wind for takeoff, regardless of wind direction.
*Ridge soaring new places without land access to the top.
*In-flight restarts allow the pilot to soar cross-country downwind and then fly under power back to his departure point.
*Restarts can also be a powerful didactic tool for learning or improving thermalling skills.
*Significant increase in soaring airtime and opportunities needed to better understand thermals, usable cloud life, sink, drift, transition glides, ridge lift, landing approach, etc.
*Ability to fly in non-thermal days.
*By far, the largest disadvantage is the engine and propeller
noise: about 90 dB at 1 m (3 ft) and about 58 dB at convert|760|m|ft AGL.
*The added harness
weightcan increase injuryin case of a severe nose in.
*There is a slightly longer set-up time with a more complex preflight.
*Requires some basic knowledge of two-stroke engine maintenance and repair.
*Fuel and oil transport.
*Slight drag increase when on glide.
*Increased effort required to weight-shift a flexible wing.
*Prone configuration units are more difficult to coordinate a sustained high bank turn.
Powered hang gliders' technology is quite young and continuously evolving and improving.
Stephan Nitsch and
Yves Rousseaubelieve that the modern hang glider is suitable for flapping flight as the flex-wing behaves like a bird wing or a bat wing and the airframe can be adapted to flapping flight driven by a compressed air engine. [Ornithopter hang glider: [http://www.jumpnfly.privat.t-online.de/ni.htm?nilinks.htm] ] [Yves Rousseau: [http://www.jumpnfly.privat.t-online.de/rouss00.jpg] ] Ducted fan
* A ducted fan offers greater propulsive efficiency and a smaller frontal area.
* By reducing propeller blade tip losses and directing its thrust towards the back only, the ducted fan is more efficient in producing thrust than a conventional propeller advancing at low speed (80 knots).
* Ducted fans are quieter than propellers: they shield the blade noise, and reduce the tip speed and intensity of the tip vortices both of which contribute to noise production.
* Complex duct design.
* Requires of high RPM and minimal vibration - Electric or
* A significant weight increase even if constructed from advanced composites.
* Tradeoff between additional power and drag increase during glide (power off) and also, at an angle of incidence of 32o, parts of the duct would be stalled and producing drag. [Jon Longbottom - Mechanical aeronautics, thesis in PDF format: [http://www.thepico.com.au/pico/images/b/bb/Drag_reduction_of_Paramotor.pdf] ]
Electric motorsOn 1979, Larry Mauroadded a landing gear to an electric "Solar Riser" hang glider; although it was the first solar airplane, it may not be universally held as the first "foot-launched" electric powered hang glider. Advances in batteries, solar cells, and ultra capacitors are being considered for bringing electric powered paragliders and hang gliders to practical and affordable use.
* Designers Csaba Lemak and Patrick MacKenzie constructed a
powered paragliderpowered by 112 Lithium Polymer ( LiPo) batteries and a Convert|17|hp|kW|0|abbr=on custom wound three phase motor weighing 1.5 kg coupled to a 3.6 to 1 reduction drive. [Electric Paramotor home page. [http://www.electricppg.com/] ] Their electric powered paraglider flew for the first time on June 6, 2006 in Ontario, Canada. With flight autonomy of only 35 minutes, it has many advantages, such as ease of operation, minimum maintenance and power output is not altitude dependent.
* Richard Kruger-Sprengel (Helix Propeller) and German designer Werner Eck, have produced at least two electric powered paraglider (EPPG) prototypes [Werner Eck, designer of an Electric PGG [http://www.marksparaglidingpages.com/] ] , their first machine flew in 2001 for 3.5 minutes and was the first EPPG; their latest prototype was tested again on March 2008 and it uses a motor described as: LEM 200 / Fa. Lemco, brushes – disc / 5.5 kg, direct current, 10 kW at 2.200 rpm, 50 Volt at 200 Ampere. Controller: Fa. Brusa, 48 V / 500 A / 1,7 kg. Battery: 14 accumulator Saft 35 Ah connected in series 14 x 3,6 V = 50,4 V. Lithium-Ion-Technology. Weight: 15 kg. Time to charge: 20 min to 2 hours. The latest efforts are described on [http://www.electricppg.com/Developments/werner_eck/index.htm Werner Eck] . Since 2007 Werner Eck is using a personal brushless direct drive outrunner; it is visible on website [http://www.sinusleistungssteller.de/index.html SLS]
* ElectroPropulsion Ltd. and Electric Flight Systems Ltd. have teamed up with the British Defence Academy scientists to assist in research and development of electric powered flight optimised for the leisure aviation market.
*Extremely easy re-start.
*Simple operation and maintenance.
*Small size components.
*No flammable fuel or oil required.
*No exhaust gases.
*Minimal cooling required, allowing for better aerodynamic profile.
*Noise produced only by the propeller.
* Battery weight, cost, recharge method.
* Flight autonomy time.
Human powered aircraft
List of personal aircraft
* [http://www.ultraflightradio.com UltraFlight Radio Show] - Internet-based weekly talk show devoted to all aspects of recreational flight.
* [http://www.glider-one.si/index.php?option=com_content&task=view&id=28&Itemid=1 Enstroj - Elektro Apis - FLY in the future with an electric self-launch sailplane APIS Electro Energy]
* [http://www.wind-drifter.com Wind-drifter] Powered harnesses' technical details, articles, etc. by Mr. Richard Cobb, a hang gliding pioneer, former Advanced Instructor and a kind contributor to this article.
* [http://www.flpa.org/ Foot Launched Powered Aircraft] Links directory by category and location.
* [http://www.airtimeproducts.com.au/atpexplorerld.html Explorer LD] manufacturer.
* [http://www.hiddenmt.com X1] manufacturer.
* [http://www.swedishaerosport.se/mosquito.htm Mosquito - NRG] manufacturer.
* [http://www.flylight.co.uk/footlaunched/index.htm DoodleBug] manufacturer.
* [http://www.waspsystems.co.uk/ Wasp] manufacturer.
* [http://www.powerplanes.com/raven.html Raven] manufacturer.
* [http://skygear.com Zenon] manufacturer.
* [http://www.fillo.cz/Fillo Fillo] manufacturer.
* [http://www.angelodarrigo.com/ Angelo d'Arrigo] Conservationist, adventurer & pilot.
* [http://www.gerrybreen.com/index1.htm Gerry Breen] - FLPHG & microlight pioneer.
* [http://groups.yahoo.com/group/e-flphg/ E-FLPHG discussion list] for questions & feedback on electric hang gliders
* [http://groups.yahoo.com/group/flphg/ FLPHG discussion list] for questions & feedback.
* [http://www.radne.se/Store/Product/ProductDetails.aspx?PartNo=3201-3 Radne Raket 120] engine.
* [http://www.geocities.com/farellus/Explorer_Modifications.html FLPHG modifications and tuning.]
* [http://www.electraflyer.com/ ElectraFlyer]
* [http://www.bhpa.co.uk British Hang Gliding and Paragliding Association]
* [http://www.bmaa.org/ British Microlight Aircraft Association]
* [http://www.abvl.com.br/ Brazilian Hang Gliding Association]
* [http://www.zeilvliegen.nl/ Dutch official hang gliding site]
* [http://www.delta-met.nl/ Dutch official hang gliding site about FLPHG in Holland]
* [http://www.dhv.de/english/index.html German Hang Gliding Association (English)]
* [http://members.aol.com/dfscinc/faq.html Hang gliding FAQ]
* [http://www.hgfa.asn.au/ Hang Gliding Federation of Australia]
* [http://www.hpac.ca/ Hang Gliding and Paragliding Association of Canada]
* [http://www.ihpa.ie/ Irish Hang Gliding and Paragliding Association]
* [http://www.hangflyg.org/ Swedish Hang Gliding Association]
* [http://www.ushga.org U.S. Hang Gliding & Paragliding Association]
* [http://www.usppa.org/ U.S. Powered Paragliding Association]
Wikimedia Foundation. 2010.
Look at other dictionaries:
hang glider — A glider, including a powered glider with the engine not operating, capable of being launched and landed solely by the use of the pilot’s legs. The term includes paragliders … Aviation dictionary
Rotary-wing hang glider — When a helicopter or gyrocopter is in engine off deliberately or inadvertently, then a sector of flight occurs that is autorotation hang gliding. When human powered helicopter flights experience the pilot in rest mode, then a hang gliding flight… … Wikipedia
Bryan Allen (hang glider) — Bryan L. Allen (born October 13, 1952 in Visalia, California) is self taught hang glider pilot and bicyclist. He achieved fame when he piloted the aircraft that won the first two Kremer prizes for human powered flight, the Gossamer Condor (1977)… … Wikipedia
Powered paragliding — Powered paragliding, also known as paramotoring, is a form of ultralight aviation where the pilot wears a motor on his or her back (a paramotor) which provides enough thrust to take off using a paraglider wing paraglider. It can be launched in… … Wikipedia
Glider — Gliders or Sailplanes are heavier than air aircraft primarily intended for unpowered flight. See also gliding and motor gliders for more details. [cite web url = http://www.ssa.org/UsTeam/adobe%20pdf/pr%20pdf/BR%20Sailplanes%20V3%2004.pdf title … Wikipedia
Powered parachute — A powered parachute (motorized parachute, PPC, paraplane) is a parachute with motor and wheels. The aircraft s airspeed is typically about 25–35 mph (40–60 km/h). PPCs operate safely at heights ranging from a few feet off the ground (while ground … Wikipedia
Hang gliding — Hang glider launching from Mount Tamalpais … Wikipedia
glider — /gluy deuhr/, n. 1. a motorless, heavier than air aircraft for gliding from a higher to a lower level by the action of gravity or from a lower to a higher level by the action of air currents. 2. a porch swing made of an upholstered seat suspended … Universalium
History of hang gliding — Hang gliding is an air sport employing a foot launchable aircraft known as a hang glider. Typically, hang gliders are composed of an aluminium or composite framed fabric wing. The pilot is ensconced in a harness depending from the airframe, and… … Wikipedia
Motor glider — DG 808B 18m self launching See also: glider (sailplane) A motor glider is a fixed wing aircraft that can be flown with or without engine power. The FAI Gliding Commission Sporting Code definition is: A fixed wing aerodyne equipped with a means of … Wikipedia