Plug flow reactor model


Plug flow reactor model

The plug flow reactor (PFR) model is used to describe chemical reactions in continuous, flowing systems. The PFR model is used to predict the behaviour of chemical reactors, so that key reactor variables, such as the dimensions of the reactor, can be estimated. PFRs are also sometimes called as Continuous Tubular Reactors (CTRs).

Fluid going through a PFR may be modeled as flowing through the reactor as a series of infinitely thin coherent "plugs", each with a uniform composition, traveling in the axial direction of the reactor, with each plug having a different composition from the ones before and after it. The key assumption is that as a plug flows through a PFR, the fluid is perfectly mixed in the radial direction but not in the axial direction (forwards or backwards). Each plug of differential volume is considered as a separate entity, effectively an infinitesimally small batch reactor, limiting to zero volume. As it flows down the tubular PFR, the residence time ( au) of the plug is a function of its position in the reactor. In the ideal PFR, the residence time distribution is therefore a Dirac delta function with a value equal to au.

PFR modelling

PFRs are frequently referred to as piston flow reactors, or sometimes as continuous tubular reactors. They are governed by ordinary differential equations, the solution for which can be calculated providing that appropriate boundary conditions are known.

The PFR model works well for many fluids: liquids, gases, and slurries. Although turbulent flow and axial diffusion cause a degree of mixing in the axial direction in real reactors, the PFR model is appropriate when these effects are sufficiently small that they can be ignored.

In the simplest case of a PFR model, several key assumptions must be made in order to simplify the problem, some of which are outlined below. Note that not all of these assumptions are necessary, however the removal of these assumptions does increase the complexity of the problem. The PFR model can be used to model multiple reactions as well as reactions involving changing temperatures, pressures and densities of the flow. Although these complications are ignored in what follows, they are often relevant to industrial processes.

Assumptions:
* plug flow
* steady state
* constant density (reasonable for some liquids but a 20% error for polymerizations; valid for gases only if there is no pressure drop, no net change in the number of moles, nor any large temperature change)
* constant tube diameter
* single reaction

A material balance on the differential volume of a fluid element, or plug, on species "i" of axial length "dx" between "x" and "x + dx" gives

[accumulation] = [in] - [out] + [generation] - [consumption] 1. F_{i}(x) - F_{i}(x+dx) + A_t dx u_i r = 0 . cite book | last = Schmidt | first = Lanny D. | title = The Engineering of Chemical Reactions | publisher = Oxford University Press | date = 1998 | location = New York | id = ISBN 0-19-510588-5 ]

When linear velocity, "u", and molar flow rate relationships, "Fi", u = frac{dot{v{A_t} = frac{4 dot{v{pi D^2} and F_i = A_t u C_i , , are applied to Equation 1 the mass balance on "i" becomes

2. A_t u [C_i(x) - C_i(x + dx)] + A_t dx u_i r = 0 , .

When like terms are canceled and the limit "dx" → 0 is applied to Equation 2 the mass balance on species "i" becomes

3. u frac{dC_i}{dx} = u_i r ,

where "Ci(x)" is the molar concentration of species "i" at position "x", "At" the cross-sectional area of the tubular reactor, "dx" the differential thickness of fluid plug, and u_i stoichiometric coefficient. The reaction rate, "r", can be figured by using the Arrhenius temperature dependence. Generally, as the temperature increases so does the rate at which the reaction occurs. Residence time, au, is the average amount of time a discrete quantity of reagent spends inside the tank.

Assume:
* isothermal conditions, or constant temperature (k is constant)
* single, irreversible reactionA = -1)
* first-order reaction (r = kCA)

After integration of Equation 3 using the above assumptions, solving for "CA(L)" we get an explicit equation for the output concentration of species "A",

4. C_A(L) = C_{Ao} e^{-k au} , ,

where "CAo" is the inlet concentration of species "A".

Operation and uses

PFRs are used to model the chemical transformation of compounds as they are transported in systems resembling "pipes". The "pipe" can represent a variety of engineered or natural conduits through which liquids or gases flow. (e.g. rivers, pipelines, regions between two mountains, etc.)

An ideal plug flow reactor has a fixed residence time: Any fluid (plug) that enters the reactor at time t will exit the reactor at time t+ au, where au is the residence time of the reactor. The residence time distribution function is therefore a dirac delta function at au. A real plug flow reactor has a residence time distribution that is a narrow pulse around the mean residence time distribution.

A typical plug flow reactor could be a tube packed with some solid material (frequently a catalyst). Typically these types of reactors are called packed bed reactors or PBR's. Sometimes the tube will be a tube in a shell and tube heat exchanger.

Advantages and disadvantages

CSTRs (Continuous Stirred Tank Reactor) and PFRs have fundamentally different equations, so the kinetics of the reaction being undertaken will to some extent determine which system should be used. However there are a few general comments that can be made with regards to PFRs compared to other reactor types.

Plug flow reactors have a high volumetric unit conversion, run for long periods of time without maintenance, and the heat transfer rate can be optimized by using more, thinner tubes or fewer, thicker tubes in parallel. Disadvantages of plug flow reactors are that temperatures are hard to control and can result in undesirable temperature gradients. PFR maintenance is also more expensive than CSTR maintenance. [ [http://www.engin.umich.edu/~cre/asyLearn/bits/pfrfinal/index.htm University of Michigan website: Plug Flow Reactors] ]

Through a recycle loop a PFR is able to approximate a CSTR in operation. This occurs due to a decrease in the concentration change due to the smaller fraction of the flow determined by the feed; in the limiting case of total recycling, infinite recycle ratio, the PFR perfectly mimics a CSTR.

Applications

Plug flow reactors are used for some of the following applications:

*Large-scale reactions

*Fast reactions

*Homogeneous or heterogeneous reactions

*Continuous production

*High-temperature reactions

ee also

*chemical reactors
*chemical reactions
*microreactor
*oscillatory baffled reactor

Reference and sources


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Plug flow — In fluid mechanics, Plug Flow is a simple model of the velocity profile of a fluid flowing in a pipe. In plug flow, the velocity of the fluid is assumed to be constant across any cross section of the pipe perpendicular to the axis of the pipe.… …   Wikipedia

  • Chemical reactor — In chemical engineering, chemical reactors are vessels designed to contain chemical reactions. The design of a chemical reactor deals with multiple aspects of chemical engineering. Chemical engineers design reactors to maximize net present value… …   Wikipedia

  • PFR (disambiguation) — PFR could refer to:* Partito Fascista Repubblicano, a former political party in Italy * Plug flow reactor model, a reactor simulation model * Pontefract Baghill railway station, England; National Rail station code PFR * PFFR, an alternative rock… …   Wikipedia

  • Mass balance — A mass balance (also called a material balance) is an application of conservation of mass to the analysis of physical systems. By accounting for material entering and leaving a system, mass flows can be identified which might have been unknown,… …   Wikipedia

  • COCO simulator — The COCO Simulator is a free of charge, non commercial, graphical, modular and CAPE OPEN compliant, steady state, sequential simulation process modeling environment. It was originally intended as a test environment for CAPE OPEN modeling tools… …   Wikipedia

  • Ignimbrite — is a volcanic pyroclastic rock, often of dacitic or rhyolitic composition. Ignimbrite is the deposit of a pumice rich pyroclastic density current, or pyroclastic flow , a hot suspension of particles and gases that flows rapidly from a volcano,… …   Wikipedia

  • Oil shale extraction — is an industrial process in which kerogen mdash;a mixture of organic chemical compounds (including hydrocarbons) found in oil shale mdash;is converted into synthetic crude oil through pyrolysis. In pyrolysis, oil shale is heated in the absence of …   Wikipedia

  • Business and Industry Review — ▪ 1999 Introduction Overview        Annual Average Rates of Growth of Manufacturing Output, 1980 97, Table Pattern of Output, 1994 97, Table Index Numbers of Production, Employment, and Productivity in Manufacturing Industries, Table (For Annual… …   Universalium

  • Nuclear meltdown — Three of the reactors at Fukushima I overheated, causing core meltdowns. This was compounded by hydrogen gas explosions and the venting of contaminated steam which released large amounts of radioactive material into the air.[1] …   Wikipedia

  • Nobel Prizes — ▪ 2009 Introduction Prize for Peace       The 2008 Nobel Prize for Peace was awarded to Martti Ahtisaari, former president (1994–2000) of Finland, for his work over more than 30 years in settling international disputes, many involving ethnic,… …   Universalium


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.