Thermionic emission

Thermionic emission
Closeup of the filament on a low pressure mercury gas discharge lamp showing white thermionic emission mix coating on the central portion of the coil. Typically made of a mixture of barium, strontium and calcium oxides, the coating is sputtered away through normal use, often eventually resulting in lamp failure.

Thermionic emission is the heat-induced flow of charge carriers from a surface or over a potential-energy barrier. This occurs because the thermal energy given to the carrier overcomes the binding potential, also known as work function of the metal. The charge carriers can be electrons or ions, and in older literature are sometimes referred to as "thermions". After emission, a charge will initially be left behind in the emitting region that is equal in magnitude and opposite in sign to the total charge emitted. But if the emitter is connected to a battery, then this charge left behind will be neutralized by charge supplied by the battery, as the emitted charge carriers move away from the emitter, and finally the emitter will be in the same state as it was before emission. The thermionic emission of electrons is also known as thermal electron emission.

The classical example of thermionic emission is the emission of electrons from a hot cathode, into a vacuum (archaically known as the Edison effect) in a vacuum tube. The hot cathode can be a metal filament, a coated metal filament, or a separate structure of metal or carbides or borides of transition metals. Vacuum emission from metals tends to become significant only for temperatures over 1000 K. The science dealing with this phenomenon has been known as thermionics, but this name seems to be gradually falling into disuse.

The term "thermionic emission" is now also used to refer to any thermally-excited charge emission process, even when the charge is emitted from one solid-state region into another. This process is crucially important in the operation of a variety of electronic devices and can be used for power generation or cooling. The magnitude of the charge flow increases dramatically with increasing temperature.

Contents

History

In reading this history, it is necessary to remember that the electron was not identified as a separate physical particle until the 1897 work of J. J. Thomson. One therefore has to be careful in using the word "electron" when discussing experiments that took place before this date.

The phenomenon was initially reported in 1873 by Frederick Guthrie in Britain. While doing work on charged objects, Guthrie discovered that a red-hot iron sphere with a positive charge would lose its charge (by somehow discharging it into air). He also found that this did not happen if the sphere had a negative charge.[1] Other early contributors included Hittorf (1869–1883), Goldstein (1885), and Elster and Geitel (1882–1889).

The Edison effect in a diode tube. A diode tube is connected in two configurations, one has a flow of electrons and the other does not. Note that the arrows represent electron current, not conventional current.

The effect was rediscovered by Thomas Edison on February 13, 1880, while trying to discover the reason for breakage of lamp filaments and uneven blackening (darkest near one terminal of the filament) of the bulbs in his incandescent lamps.

Edison built several experiment bulbs, some with an extra wire, a metal plate, or foil inside the bulb which was electrically separate from the filament, and thus could serve as an electrode. He connected a galvanometer, a device used to measure current, to the output of the extra metal electrode. When the foil was charged negatively relative to the filament, no charge flowed between the filament and the foil. We now know that this was because the filament was emitting electrons, and thus were not attracted to the negatively charged foil. In addition, charge did not flow from the foil to the filament because the foil was not heated enough to emit charge (later called thermionic emission). However, when the foil was given a more positive charge than the filament, negative charge (in the form of electrons) could flow from the filament through the vacuum to the foil. This one-way current was called the Edison effect (although the term is occasionally used to refer to thermionic emission itself). He found that the current emitted by the hot filament increased rapidly with increasing voltage, and filed a patent application for a voltage-regulating device using the effect on November 15, 1883 (U.S. patent 307,031,[2] the first US patent for an electronic device). He found that sufficient current would pass through the device to operate a telegraph sounder. This was exhibited at the International Electrical Exposition in Philadelphia in September 1884. William Preece, a British scientist took back with him several of the Edison Effect bulbs, and presented a paper on them in 1885, where he referred to thermionic emission as the "Edison Effect." [3] The British physicist John Ambrose Fleming, working for the British "Wireless Telegraphy" Company, discovered that the Edison Effect could be used to detect radio waves. Fleming went on to develop the two-element vacuum tube known as the diode, which he patented on November 16, 1904.

The thermionic diode can also be configured as a device that converts a heat difference to electric power directly without moving parts (a thermionic converter, a type of heat engine).

Following J. J. Thomson's identification of the electron, the British physicist Owen Willans Richardson began work on the topic that he later called "thermionic emission". He received a Nobel Prize in Physics in 1928 "for his work on the thermionic phenomenon and especially for the discovery of the law named after him".

Richardson's Law

In any solid metal, there are one or two electrons per atom that are free to move from atom to atom. This is sometimes collectively referred to as a "sea of electrons". Their velocities follow a statistical distribution, rather than being uniform, and occasionally an electron will have enough velocity to exit the metal without being pulled back in. The minimum amount of energy needed for an electron to leave a surface is called the work function. The work function is characteristic of the material and for most metals is on the order of several electronvolts. Thermionic currents can be increased by decreasing the work function. This often-desired goal can be achieved by applying various oxide coatings to the wire.

In 1901 Richardson published the results of his experiments: the current from a heated wire seemed to depend exponentially on the temperature of the wire with a mathematical form similar to the Arrhenius equation. Later, he proposed that the emission law should have the mathematical form [4]

J = A_{\mathrm{G}} T^2 \mathrm{e}^{-W \over k T}

where J is the emission current density [SI unit: A/m2], T is the thermodynamic temperature of the metal [SI unit: kelvin (K)], W is the work function of the metal, k is the Boltzmann constant, and AG is a parameter discussed next.

In the period 1911 to 1930, as physical understanding of the behaviour of electrons in metals increased, various different theoretical expressions (based on different physical assumptions) were put forwards for AG, by Richardson, Dushman, Fowler, Sommerfeld and Nordheim. Over 60 years later, there is still no consensus amongst interested theoreticians as to what the precise form of the expression for AG should be, but there is agreement that AG must be written in the form

 A_{\mathrm{G}} = \; \lambda_{\mathrm{R}} A_0

where λR is a material-specific correction factor that is typically of order 0.5, and A0 is a universal constant given by [4]

A_0 = {4 \pi m k^2 e \over h^3} = 1.20173 \times 10^6\,\mathrm{A\,m^{-2}\,K^{-2}}

where m and −e are the mass and charge of an electron, and h is Planck's constant.

In fact, by about 1930 there was agreement that, due to the wave-like nature of electrons, some proportion rav of the outgoing electrons would be reflected as they reached the emitter surface, so the emission current density would be reduced, and λR would have the value (1-rav). Thus, one sometimes sees the thermionic emission equation written in the form

J = (1-r_{\mathrm{av}}) A_0 T^2 \mathrm{e}^{-W \over k T}.

However, a modern theoretical treatment by Modinos assumes that the band-structure of the emitting material must also be taken into account. This would introduce a second correction factor λB into λR, giving AG = λB(1 − rav)A0. Experimental values for the "generalized" coefficient AG are generally of the order of magnitude of A0, but do differ significantly as between different emitting materials, and can differ as between different crystallographic faces of the same material. At least qualitatively, these experimental differences can be explained as due to differences in the value of λR.

Considerable confusion exists in the literature of this area because: (1) many sources do not distinguish between AG and A0, but just use the symbol A (and sometimes the name "Richardson constant") indiscriminately; (2) equations with and without the correction factor here denoted by λR are both given the same name; and (3) a variety of names exist for these equations, including "Richardson equation", "Dushman's equation", "Richardson-Dushman equation" and "Richard-Laue-Dushman equation". In the literature, the elementary equation is sometimes given in circumstances where the generalized equation would be more appropriate, and this in itself can cause confusion. To avoid misunderstandings, the meaning of any "A-like" symbol should always be explicitly defined in terms of the more fundamental quantities involved.

Because of the exponential function, the current increases rapidly with temperature when kT is less than W. (For essentially every material, melting occurs well before kT=W.)

Schottky emission

In electron emission devices, especially electron guns, the thermionic electron emitter will be biased negative relative to its surroundings. This creates an electric field of magnitude F at the emitter surface. Without the field, the surface barrier seen by an escaping Fermi-level electron has height W equal to the local work-function. The electric field lowers the surface barrier by an amount ΔW, and increases the emission current. This is known as the "Schottky effect" or field enhanced thermionic emission. It can be modeled by a simple modification of the Richardson equation, by replacing W by (W − ΔW). This gives the equation[5][6]

J (F,T,W) = A_{\mathrm{G}} T^2 e^{ - (W - \Delta W) \over k T}
\Delta W = \sqrt{e^3 F \over 4\pi \epsilon_0},

where ε0 is the electric constant (also, formerly, called the vacuum permittivity).

Electron emission that takes place in the field-and-temperature-regime where this modified equation applies is often called Schottky emission. This equation is relatively accurate for electric field strengths lower than about 108 V  m−1. For electric field strengths higher than 108 V m−1, so-called Fowler-Nordheim (FN) tunneling begins to contribute significant emission current. In this regime, the combined effects of field-enhanced thermionic and field emission can be modeled by the Murphy-Good equation for thermo-field (T-F) emission.[7] At even higher fields, FN tunneling becomes the dominant electron emission mechanism, and the emitter operates in the so-called "cold field electron emission (CFE)" regime.

Thermionic emission can also be enhanced by interaction with other forms of excitation such as light.[8] For example, excited Cs-vapours in thermionic converters form clusters of Cs-Rydberg matter which yield a decrease of collector emitting work function from 1.5 eV to 1.0–0.7 eV. Due to long-lived nature of Rydberg matter this low work function remains low which essentially increases the low-temperature converter’s efficiency.[9]

Photon-enhanced thermionic emission

Photon-enhanced thermionic emission (PETE), a process developed by engineers at Stanford University, that harnesses both the light and heat of the sun to generate electricity and increases the efficiency of solar power production by more than twice the current levels. The device developed for the process reaches peak efficiency after it reaches 200°C; most silicon solar cells become inert after reaching 100°C. Such device will work best in parabolic trough collectors, which reach temperatures around 800°C. Although the team used a gallium nitride semiconductor in its "proof of concept" device, it claims that the use of gallium arsenide can increase the device's efficiency to 55–60 percent, nearly triple that of existing systems[10][11], which is only 12 - 17 percent more than existing 43 percent multi-junction solar cells.[12]

See also

References

  1. ^ Owen Richardson (1921). The emission of positive ions by hot metals. ISBN 9781929148103. http://books.google.it/books?id=PrbOIoMnxnwC&pg=PA196. Retrieved 2009-07-11. 
  2. ^ U.S. Patent 307,031
  3. ^ "Edison" by Matthew Josephson. McGraw Hill, New York, 1959, ISBN 07-033046-8
  4. ^ a b C.R. Crowell, The Richardson constant for thermionic emission in Schottky barrier diodes, Solid-State Electronics, Volume 8, Issue 4, April 1965, Pages 395-399, ISSN 0038-1101, DOI: 10.1016/0038-1101(65)90116-4. (http://www.sciencedirect.com/science/article/B6TY5-46V0D3J-1J/2/b1524bc945ea4550de749e0328bb51ce)
  5. ^ M.E. Kiziroglou, X. Li, A.A. Zhukov, P.A.J. de Groot, C.H. de Groot, Thermionic field emission at electrodeposited Ni-Si Schottky barriers, Solid-State Electronics, Volume 52, Issue 7, July 2008, Pages 1032-1038, ISSN 0038-1101, DOI: 10.1016/j.sse.2008.03.002. Sciencedirect.com
  6. ^ Orloff, Jon (2008) [1997]. "Schottky emission". Handbook of Charged Particle Optics (2 ed.). CRC Press. pp. 5–6. ISBN 978-1420045543. http://books.google.it/books?id=y0FF19lud5YC&pg=PA6&lpg=PA6&dq=#v=onepage&q=&f=false. Retrieved 2009-09-07. 
  7. ^ E.L. Murphy and R.H. Good, "Thermionic Emission, Field Emission, and the Transition Region", Phys. Rev. 102(6), pp. 1464-1473 (1956).
  8. ^ A.G. Mal'shukov1 and K.A. Chao, "Opto-Thermionic Refrigeration in Semiconductor Heterostructures," Phys. Rev. Lett. 86, pp. 5570-5573 (2001).
  9. ^ R. Svensson, L. Holmlid. Very low work function surfaces from condensed excited states: Rydber matter of cesium. Surface Science, V. 269/270, pp. 695-699 (1992). doi:10.1016/0039-6028(92)91335-9
  10. ^ Bergeron, Louis (August 2, 2010). "New solar energy conversion process discovered by Stanford engineers could revamp solar power production". Stanford Report. http://news.stanford.edu/news/2010/august/new-solar-method-080210.html. Retrieved August 4, 2010. 
  11. ^ Schwede, Jared W.; Bargatin, Igor; Riley, Daniel C.; Hardin, Brian E.; Rosenthal, Samuel J.; Sun, Yun; Schmitt, Felix; Pianetta, Piero et al. (1 August 2010). "Photon-enhanced thermionic emission for solar concentrator systems". Nature Materials 9: 762. Bibcode 2010NatMa...9..762S. doi:10.1038/nmat2814. http://www.nature.com/nmat/journal/vaop/ncurrent/full/nmat2814.html. 
  12. ^ url = http://onlinelibrary.wiley.com/doi/10.1002/pip.1088/abstract

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • thermionic emission — n. the phenomenon of electron or ion emission from the heated surface of a conductor * * * ▪ physics       discharge of electrons from heated materials, widely used as a source of electrons in conventional electron tubes (e.g., television picture …   Universalium

  • thermionic emission — n. the phenomenon of electron or ion emission from the heated surface of a conductor …   English World dictionary

  • thermionic emission — therm·ion·ic emission .thər (.)mī än ik n emission of particles (as electrons) from materials at high temperature due to the heat energy imparted to them * * * the emission of electrons and ions by incandescent bodies …   Medical dictionary

  • thermionic emission — noun the emission of electrons from very hot substances • Syn: ↑thermal emission • Hypernyms: ↑emission …   Useful english dictionary

  • thermionic-emission current — termoelektroninė srovė statusas T sritis automatika atitikmenys: angl. thermionic current; thermionic emission current; thermoelectronic current vok. Glühelektronenstrom, m; Glühemissionsstrom, m rus. термоэлектронный ток, m; ток термоэлектронной …   Automatikos terminų žodynas

  • Emission — may refer to: * Flue gas, also: ** Exhaust gas, flue gas occurring as a result of the combustion of a fuel * Emission of air pollutants * Emission (electromagnetic radiation), the process by which the energy of a photon is released by another… …   Wikipedia

  • thermionic current — n. a current resulting from directed thermionic emission, as the flow of emitted electrons from a heated cathode to the plate …   English World dictionary

  • thermionic power converter — ▪ electronics Introduction also called  thermionic generator,  thermionic power generator,  or  thermoelectric engine        any of a class of devices that convert heat directly into electricity using thermionic emission rather than first… …   Universalium

  • Thermionic converter — A thermionic converter consists of a hot electrode which thermionically emits electrons over a potential energy barrier to a cooler electrode, producing a useful electric power output. Caesium vapor is used to optimize the electrode work… …   Wikipedia

  • thermionic — adj. of or relating to electrons emitted from a substance at very high temperature. Phrases and idioms: thermionic emission the emission of electrons from a heated source. thermionic valve (US tube) a device giving a flow of thermionic electrons… …   Useful english dictionary


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.